Thanks for a very well done video. It makes sense that you would have the concave bends as that metal has to go somewhere but I've never really understood until today. Thanks!

Very impressive,anybody who has tried to bend box section will testify to just how tricky it is to do without making a mess of it! This is so much easier than slaving away with home made formers,clamps,lots of heat and swearing!

Thank you for a very clear explanation of how this is done. Would you have a similar operation for low volume manual bends?

Great information....I'm in the design process for fabricating a wrought iron security gate for my front porch; it has a brick archway and I want to make the gate curved to match the archway. Looks like I"ll probably end up taking my metal to a machine shop for the bends. I appreciate your video...especially the point you make about the thicker walled tubing. Can't believe people would dislike your information! Thanks again.

Thank you for the wonderful video. You are my teacher of the day!

Thank you for the explanations

Great informational video! thanks!

Thanks I kinda already knew that the bends stretched metal has to go somewhere I've done a lot of torch heating and bending, never with a hydraulic press. I've been wanting to make a press with diffrent attachments electric or air, hand 2-4 ton jack I could make all kinds of neat stuff instead of cutting bending and welding that's a lot of steps especially if you have to make several the same thing and they all have to match. Thanks for sharing the video that explains why I see the dimples on curved square tubing.

Thanks for a wonderful didactic video. Definitely having you as my online mentor.

That was well done........ Thank You!

I use to build ski lifts and I bent bales which are the horse shoe shaped tubing hanging off the cable that holds the chair. usually 1"1/2 The bender we used was capable of bending 3" square tube and ours left the tube concave on each side.. very informative

This man in the video is a natural actor. I hope he gets involved in community theater. There are a lot of roles he could do well.

how and where can this machine by? and what is the cost for this squire tube and round tube bender, like this simple system bender machine?

Great video...i have a pet project that will require a trough ie a 180 degree bent sheet metal. How best can i achieve this on the cheap? Do i need to roll a sheet metal?

Enjoyed the video and the info. Thanks.

Nice work

Did you bend the piece you were holding at 4:38 with one of your machines? That's a good bend for that size rhs

Is that the JMR ultra bender, with optional hydraulics?

Which bending machine would you recommend?

Like this machine! How can I buy one

Thanks a lot. It was very helpful.

Good presentation.

Awsome, nice demonstration, informatively clear, and fairly simple, But you know????? I really think you could have put more emphasis on the several types of dies and what they will make ultimately, and even shown how the benders are set up and why. But, I like your video,👍

THANKS THE INSIDE PART YOU TOOK OFF FIRST IS CALLED THE SLIPPER, great vid

Mon I always wanted to learn to bend tubing I could make some killer stuff. Instead of cutting then bending and weld closed to make it look like it was bent but a lot of steps to get that bend. A bender would be much easier.

very very nice machine

Thanks for letting me know. I am trying to bend square rod like a H and hoped this could help, but, guess I will have to make my own failed or successful bend on that. ;) Thanks I have an idea on how to make it happen thanks to this vid though. ;)

very nice

I operate a mandrel bender..keeps the deformation out of bend area..and followblock smothes out all i.d. wrinkles

Nice video

where can i find already bent tubing

what's the name of this machine

Love your class , where can I buy the square pipe bending machine

Thanks for the insight. Would it be possible to bend a 1 1/2” x 3” square tubing that’s solid aluminum ?

Cool.

Woow good

Thanks for this video its helpful to explain to clients why I cant give them a perfectly square rolled tube despite having a good ring roller. I'm curious what type of roller or process would produce a rolled tube without the inner and outer deformation? Obviously more than a fabricator can afford- still curious. Something with a mandrel I guess?

goodWork

Do the dimples compromise strength or steels integrity?

Would the dimple give it a little extra strength

So thicker is better up to a point, good to know

Can this bend rectangle tubing?

👍👍👍

Skip to 5:30 to actually see the bending. Up to that point: "square tube needs a deformation indent on inside and outside radius."

I need Flange fabrication by using MS flat.32*5mm .Flange will be use for jointing sheet metal round duct10"dia to18"dia*1.5mm thk Gi plain sheet .

I'd love to see how Vehicle Chassis are formed with all the bending of the Axles

What's the cost of this equipment??

Stupid question....I'm still young and working from my back yard....Is there any any way to do it without these kind of benders ??

This guy could have covered this topic in 3min, dragging it out for sponsors. Ridiculous