You're welcome!

Because the LCD screen and digitiser glass panel of the iPad 6th generation is not laminated, it’s not recommended to do DIY to replace the battery, there are big chances of getting tiny bits of dusts or fluffs inside the screen and made it look like dead pixels. … iPad Air 2 has laminated screens, that means the digitiser and the LCD screen are in one piece after taking the iPad apart, so unlike the iPad 6th generation as seen in this video. Over a year ago I kept it in mind not to buy repaired iPad 6th generation, but this year ended up buying one used, and the seller had replaced the screen, it has 4 tiny bits inside the screen!

@@yatlonou-kb8zr well it worked perfect for me and now my battery last all day and not just 10 min :)

@@budz9461where did you get the battery from ?

Great 👍

Thanks for your Feedback..

You're welcome

Thanks 🙏

Always 🙏

Hair dryer will do

Thanks

For the process, I would say about 1 hour

👍

There are two types. You can find pre-cut adhesive for 2018 model and if not b7000 / T8000 Glue

I didn’t understand what you mean?

Glad it was helpful!

Thanks

The battery is dead. The iPad approximates the battery’s charge from the voltage it’s outputting but when a battery gets old the voltage output will get lower and if it progresses beyond a certain threshold the iPad will shut down even though it still is partially charged the voltage output is just too low. That’s how I understand it.

Please send me the video timestamp, i will let you know which part you need

Well there are local repair shops that can help you. Your location?

Start with about 2 minutes all around edges.. and then keep continue until you can create a gap.. after 2-3 initial step, then you can go with 1 minute at a time..

Thanks for your feedback

Thanks. You need to heat the device to take off the screen. Do you have any heating unit?

@@DIYGeardo Thanks, for replying I only have a hair dryer, but after hours I got it open. But now comes the struggle of trying to remove the battery. I think I am going to use the hair dryer to heat the back and 100% isopropyl alcohol.

Where do you get the battery from , can you take it somewhere to replace the battery? Mine just stop coming on and I love this iPad don’t want to get a new one

Too strong

The model number is a1954,a1893.. it is same as the iPad Air battery

iPad 6 (2018) battery is same as 5 (2017) and air..it is kind of common battery for iPads. Also it is the same battery for ipad 7,8 too (10.2 models)

@@DIYGeardo ipad air all models battery can fit in ipad 6th gen??

@@goddavid5162 no, only iPad Air 1, iPad Air 2,3 &4 are different. iPad Air , 2017,2018, iPad 7,8 are same

@@goddavid5162What happened sir? Find a battery with the recommendations?

You need to Apply little heat and create a Gap, The initial process may take sometime, Need patience

@@DIYGeardo thanks I got it

Depend on how you rate your self and patience.It is not easy

Your location?

@@DIYGeardo europe poland

it is hard for us to ship due to new aviation rules. You need to check locally.Sorry, you can try Germany, there are many online shops, but again check how they send.There are limitations

i mean do not put too much force into it..The board is strong, but doesn't mean it is strong enough..without removing the board, this the easiest way to take off the battery..

@@DIYGeardo i try to follow your vedio to get my battary done, however found very strong glue under knee the board, cannot bent that much like in vedio, really worry about to damage the ipad

@@huangda2161you use card pry tool to cut the adhesive, if not little more heating will do the job

Resell? Means the battery ?

Sorry. I meant reseal

@@fargogemini694 Adhesive or b7000/t7000 glue..DO not ever use super glue

Well it depends on the place

Thanks for your feedback

Amazon

Not the manufactures battery..... it's a third-party battery..Only way to get a manufactures batteries get it fixed buy apple themselves...$99 is fairly cheap to get it repaired

not sure exactly what you mean, but needs to lift the board to remove the battery ? isn't it, any suggestions are welcome ?

@@DIYGeardo You do have to lift the board but it's easier to loosen from around the battery connector, this will allow access to the connector without unscrewing any other component. Most of the motherboard is glued down and is pretty flexible if you go carefully.

@@joeylee3756 i Definitely agree! i just think its so Unnecessary to unplug all that extra stuff above the ipad. You can easily bend the board up and slip the ipad battery contacts to the teeth.

Thanks for your feedback.. will try to improve 🙏

Well yes, to repair ipads , they need to remove the screen..Sometimes there is a chance of breaking the LCD..It depend on the Tech and sometimes even Pros will have issues.

this is not a screen replacement video, so it didn't talk about that. sorry you learned about the home button the hard way

yeah kind of

Any suggestions ?