It is not difficult for me to assemble a broken axle housing like a pen #difficult #assemble #broken #axle #housing #like #pen
Пікірлер: 47
@tonteria245 ай бұрын
It's strange that the break is so square, it had probably already broken there before.
@The_Black_Sheep956 ай бұрын
That differential been "repaired" many many times before
@cmsracing6 ай бұрын
No way they're getting %100 penetration without beveling the edges before welding.
@oldschool19936 ай бұрын
I want some of that Pakistani welding rod- gets penetration through mud, oil, grease, dirt and you never have to bevel your parts.
@hasanurrahman59646 ай бұрын
Not even 25%!
@DEREK-mq3ik6 ай бұрын
And not cleaning the weld surface? All that grease and dirt in the weld?? SMH
@ThanhNguyen-kw2mz6 ай бұрын
🙌🙌🙌🙌🤣🤣🤣🤣
@bobhudson66595 ай бұрын
Yes. They had the root clearance but what happened to the 60 degree V? Also how do you weld into iron oxide from the flame cut - plus no V? As others have mentioned maybe 25% penetration. Wonder how long the always overloaded truck lasted afterwards?
@antoniovalverdemoreno1256 ай бұрын
Otro gra trabajo,que por cierto,un trabajo imposible de hacer en España,salud y buena suerte...🐧
@gordonwelcher95985 ай бұрын
They have to overload the trucks to get the job, then drive a dangerous vehicle to make money. After that they have to spend the money they made for repairs. Not an ideal system.
@pkfan51126 ай бұрын
Only one man wear shoes, others sandals, no gloves, no safety glass sorry for those people, they don’t have any protection at all
@MushtaqAhmed-xs8jx5 ай бұрын
Mashallah Good work amazing zabardast
@joelchabot51676 ай бұрын
Strange regular failure, scam?
@plumbcrazy3755 ай бұрын
I'm impressed with how much they get done with basic tools if they didn't overload the trucks wouldn't have catastrophic failures
@lockeM1406 ай бұрын
No prep before welding shocking work
@user-uz7yf5xc9uАй бұрын
No good welding because they did not make edge preparation at all. therefore cannot get good strength.
@raphaquan6 ай бұрын
It must be a very common factory problem, due to the type of cut and they even have a lathe designed for that type of axle.
@ipaddlemyowncanoe.74416 ай бұрын
It's amazing what you guys do with what you have. No big shop with all fancy tools. Use the basics to get the job done. Good stuff. 👍👍🇨🇦🙂
@starybezpiek78806 ай бұрын
Ten most już kiedyś pękł i pęknie ponownie.
@tomaszkulik87615 ай бұрын
Przy takim przeładowaniu pęknie... Dziwię się, że nie fazują krawędzi przed spawaniem.
@samsudeenjainulabdeen9126 ай бұрын
This kind of work never succeed. Not advisable. Foolish work.
@user-vs3fu8pb3y5 ай бұрын
Молодцы ребята , у вас золотые руки и наплюйте на все санкции --вы все равно правы.
@user-cn9cd6fj4n5 ай бұрын
Что за диск на болгарка не убиваемый индусы молодцы , Вася Я ишим
@jonfoster15665 ай бұрын
Meets or exceeds all 3rd world country safety and repair standards.
@chrisbanning4136 ай бұрын
Wonder how they check the axle is aligned with the diff centre
@agussoediro54156 ай бұрын
Bagus,Paman 👍👍👍👍
@mikespain86556 ай бұрын
Install a rubber mat in back of vehicle to protect the bed.
@gothicblood20614 ай бұрын
so that's a broken axle no that looks like its been cut up to look like a broken axle and the back end of the axle been fix up be for , can see the cuts in the axle . on the bearing shaft where the bearing sits had it , there been no oil or Greece on or in axle for some time where the axle shaft gos in got lot of rust in the ends didn't clean the part where you groove for welding
@tamduong28755 ай бұрын
Những người thợ khá tốt nếu vào hảng sẻ thay một cái mới rất tốn tiền
@samsudeenjainulabdeen9126 ай бұрын
No groove for welding root run penetration
@AmusedBarnOwl-hc1zg5 ай бұрын
Yeah safety first I always say
@user-dj5gf9jp8g6 ай бұрын
Cool work thanks 👍
@jamestone2655 ай бұрын
New pickup hauler…
@junjun43885 ай бұрын
I wonder how much stuff they get in there eyes
@charles679056 ай бұрын
4:39. 🤦🏻♂️🤦🏻♂️🤦🏻♂️
@The_Black_Sheep956 ай бұрын
LMAO
@MrFadicuz4 ай бұрын
@user-sb4er9wc6u5 ай бұрын
도로가 무법천지네 신호등도 없고
@thepubliceye5 ай бұрын
Just another show and tell made for KZfaq.
@anjumaneity25516 ай бұрын
BY g
@lockeM1406 ай бұрын
Cowboys
@KeithWebb-cl1ld5 ай бұрын
No they are indians
@progvinyl90215 ай бұрын
Great job done.Good welding strong as new.
@zachariebrummaire46956 ай бұрын
Fake failure and stupid repair !
@Sl205 ай бұрын
Love it !!!!!!very smart move !!!!!!,🔴🫢🤫 16:45
@Sl205 ай бұрын
Well if it broke underneath!!!!!!maybe this is the problem and a modification is need it!!!!! 21:02 🔴🫢🤫