James Duff T-Rex Radius Arm Install

No video

James Duff T-Rex Radius Arm Install

Рет қаралды 17,498

Bronco Garage

Күн бұрын

Пікірлер: 32

@BroncoGarage 4 жыл бұрын

🦖🦖 Learn more about the t-rex stock replacement radius arms here: bit.ly/2FIpMra 🦖🦖

@brianherzog6367 Жыл бұрын

Hey guys, wanted to thank you for the advice on the “Bronco Lean” portion of the video. I’m doing a frame off resto-mod and just put the body on and dropped it on its wheels and noticed the “lean” ugh! Well, took it all apart, re-greased the C bushings and found one C bushing upside down. Took extra care and time cross torquing the bolts and Shazam the frame and body are within 1/8”….. thanks guys!

@MrTzeiss 2 жыл бұрын

Please do a video of you installing your extended radius arms.

@fedupfaces 11 ай бұрын

I installed a 2.5” lift from Toms and unfortunately I didn’t grease the radius bushings no mention of it in the literature either … this pisses me off

@Johntasticful 5 жыл бұрын

Great Vid. I’m jonesing. Going to get my bronco on T-Rex! Thx!

@nickefgen9219 2 жыл бұрын

I’ll be getting the duck lift with those for my bronco

@bizzarromage 4 жыл бұрын

I miss bronco days in Mike’s shop. I am alone here in Georgia. Do you still have that monster Bronco?

@BroncoGarage 4 жыл бұрын

We have heard it exists but no one around the shop has seen it for several years.

@freddenton5857 5 жыл бұрын

Great video Jon and Mike. Looking forward to installing a set on my 76. Hey Jon, refresh my memory. How much lift did you install on your Bronco? You might want to mention that in the video. Fred

@1geniusl 5 жыл бұрын

2.5”

@GDunc 5 жыл бұрын

Any body lift?

@BroncoGarage 5 жыл бұрын

Jon’s Bronco is running a 2.5” SL and 1” BL on 35’s

@scottmassey4330 3 жыл бұрын

How much lift on Nashville Bronco?

@BroncoGarage 3 жыл бұрын

2.5” suspension and 1” body

@csprick11 5 жыл бұрын

Like those a lot, I’m thinking the duck tuff package but do they only come in blue or is there a black option for all these components as well?

@BroncoGarage 5 жыл бұрын

Ducktuff is the best of the best! The system comes in black & blue.

@billh3074 4 жыл бұрын

Where are those jack stands from?

@BroncoGarage 4 жыл бұрын

Custom built out of square tubing

@billh3074 4 жыл бұрын

Bronco Garage nice!

@fastwest433 5 жыл бұрын

Great video guys. Can you post a link to the Bronco lean video mentioned for us lazy guys?

@BroncoGarage 5 жыл бұрын

You bet! Once it comes out we will have a link in this video and in the description.

@michaeltorres2127 5 жыл бұрын

So what benefits do you get with the Trex arms? Better handling? And articulation?

@BroncoGarage 5 жыл бұрын

Better handling, better articulation, allows you to run up to a 37" tire. Eliminates 50 year old rusty radius arms. More info on dufftuff.com - bit.ly/2Z5YGlE

@michelinabjorkland 4 жыл бұрын

Will 7* bushings with a 3.5” lift be too much pinion angle ?

@BroncoGarage 4 жыл бұрын

Typically no but all Bronco's are just a little different. Best to reach out to James Duff to get all your questions answered in detail. 865-938-6696

@homeplusinspectionservices2502 3 жыл бұрын

I am not installing the T-Rex arms yet. I am replacing the C-Bushing with 7deg bushings and I am having problems getting both the radius arms to sit flush on the floor. Any tricks to get them to adjust? If its a half inch how much might that show?

@BroncoGarage 3 жыл бұрын

You want to be less than 1/8" different from side to side. Before going any further, verify the axle is 100% parallel with the ground and that the ground is even. I like to use a digital level to verify the axle is parallel with the ground.

@homeplusinspectionservices2502 3 жыл бұрын

@@BroncoGarage ok. Thanks for the response. I have a 6ft level and have layed it across the floor and across the top of both disc brake shields. Both are level and I have to assume they're parallel. If I continue to loosen things up and retighten how would I go about adjusting? I have been loosening it and wiggling it around and retightening.

@BroncoGarage 3 жыл бұрын

@@homeplusinspectionservices2502 In your case since your arms are 1/2" different from side to side which is A LOT, you will want to use dawn dish soap on the C bushings. Make darn sure they are in correctly then tighten them like shown in the video. Once you have got them as close as possible you will need to manipulate them like we did in the video. be sure to have a spray bottle of water and keep the C bushings moist until you have the arms level. Get them within an 1/8" of each other and then you will be good.