No video
XL4015 5A DC-DC Stepdown Buck Converter | Adjustable Module
Рет қаралды 18,676
3 жыл бұрынThe XL4015 power module is a DC to DC step-down (BUCK) power module that operates at a switching frequency of 180kHz. In such high frequency, it provides smaller sized filter components compared with low frequency switching regulators.
This DC-DC switching buck converter is capable of driving a 5A load with excellent line and load regulation. The main switching component is XL4015, an adjustable output version switching regulator. It is an efficient switching regulator and the output efficiency is significantly higher in comparison with the popular boost regulators. At higher input voltages, the regulator operates at a switching frequency of 180kHz, thus allowing the overall board size to be smaller and space-saving. It is a high-power switching module with a toroidal ring inductor.
Features and Specifications
Input voltage: 4 - 38V
Output voltage: 1.25 - 36V (adjustable)
Output current: Maximum output current 5A
Note: The higher the voltage, the load current increases. Try to use it within 4.5A.
Output power: It is recommended to use within 75W
Note: Heat sink required if output power exceeds 50W
Efficiency of this regulator up to 96%
Note: Efficiency is related to input, output voltage, current, and the voltage difference
Load regulation: 0.8%
Voltage regulation: 0.8%
Adjustable potentiometer onboard for output voltage adjustment.
Power LED indicator
Thermal Protection enabled.
Short circuit proportion: limited to 8A.
Dimension: 54*23*18 mm (L*W*H)
Component's Needed:
•Xl4015 Module
•50K ohm Potentiometer
•12v 35W light bulb
•wires
•Soldering
Subscribe to my channel and click the bell button to be updated on my next video. Thank you for watching♥️Enjoy and have a great day.
Subscribe to this channel: / javiersdiy
Related DIY videos:
DIY RC Car from Cardboard:
• How to Make RC Car Fro...
DIY 12v Power Supply:
• How to Make 12v Power ...
DIY 13000 mAh Powerbank:
• How to Make a 13000 mA...
DIY Sander Disk from Old DVD/CD player:
• How to Make a Mini San...
3 in 1 Power Supply:
• How to Make a 3 in 1 P...
DIY VU Meter:
• How to Make a VU Meter...
DIY Face shield:
• How to Make DIY Face S...
DIY Tester:
• How to Make Test Light...
DIY Flashlight:
• How to Make Emergency ...
DIY RC Car:
• How to Make RC Car Fro...
DIY Generator:
• How to Make Generator ...
DIY Air Cooler:
• How to Make a Powerful...
DIY Water Pump:
• How to Make Powerful W...
DIY Air Pump:
• How to Make an Air Pum...
#XL4015Module
#5ABuckConverter
#StepdownBuckModuleConverter
@henrydelacruz1284 2 ай бұрын
Muchas gracias por toda la explicacion y sobretodo por responder las preguntas...GRACIAS MIL
@JaviersDIY 2 ай бұрын
for better understanding please use the universal language
@jsmythib 2 жыл бұрын
A very handy board level gadget. I can see why they sell in multiples. Mine will be here tomorrow! Thanks for the look.
@NAVEENnaveen-cu3tp 2 жыл бұрын
Ok bro i am used but step up level not working only step down
@nickadelan 3 жыл бұрын
Keep us inspired. 😘😘
@fixnreview 3 жыл бұрын
OK kaau! Atonghutdonningdaghangpahinumdomgkansinugdanhangtodmahuman
@JaviersDIY 3 жыл бұрын
Salamat kaau sir. Sa supporta.
@fixnreview 3 жыл бұрын
@@JaviersDIY way sapayan
@user-bg5vo1wk9q 10 ай бұрын
брат видео 👍👍👍 добавь lm358 и пару резисторов и можна регулировать ток 👍👍
@JaviersDIY 10 ай бұрын
for better understanding please use the universal language
@rakshithballal6988 2 жыл бұрын
If we connect 12v generator to input side will it give constant 6v output for variable voltage
@swapniljoshi9997 Жыл бұрын
How do you set current in thi
@JaviersDIY Жыл бұрын
The current is already constant
@oneundecided Жыл бұрын
I purchased a red XL4015 5A dual pot module and the potentiometers are located a bit differently there. My Li-Ion battery is 3.7V/800mAh. When I set up the output voltage to 4.2 volts with the potentiometer (physically located closest to the voltage input terminals which is in my case 7.5 volts) then measure the output short-circuit current with 10A current range multimeter it is always 2350 mA regardless of the position of the constant current potentiometer (physically located closest to the voltage output terminals which is in my case 4.2 volts). If I connect my Li-Ion battery is 3.7V/800mAh and measure the charging current it is always 50 mA regardless of the position of the constant current potentiometer (physically located closest to the voltage output terminals which is in my case 4.2 volts). Question - how to adjust the constant current potentiometer to make the output current reach the predetermined overcurrent protection value of 800 mA? I have already tried 3 out of 5 modules you sent me -all are the same. You have the blue XL4015 5A single-pot module in this video.
@JaviersDIY Жыл бұрын
Before you put the battey make sure you already set the current output and to do that is you need to short the positive and negative then measure the current to the desired need of the battery then after that one you can now put the battery and charge.
@sadeeshadil7930 2 жыл бұрын
Is it okay 12v 1A input for this item by router charger
@JaviersDIY 2 жыл бұрын
Yes sir you can.
@rezaramadhani1513 2 жыл бұрын
why this modul need to change like that ? why we not use it directly ?
@JaviersDIY 2 жыл бұрын
It depends on you sir.
@rezaramadhani1513 2 жыл бұрын
@@JaviersDIY but, when i tried without change like you do, it doesn't work, and try to like you do, it works, maybe the potensiometer was broke
@alvaromartin1529 2 ай бұрын
Why 1n4007 diode?
@JaviersDIY 2 ай бұрын
because i want 1A current will just pass
@arvinthm8610 2 жыл бұрын
Will it provides continuous 5 amps output or provides amps depending upon current required. I am planning to use it with raspberrypi-4 with external hdd, will it provides required amps for both?
@JaviersDIY 2 жыл бұрын
It depend on the current input sir. Meaning to say if you put an 6 amp input supply the output would always 5 amp constant .
@arvinthm8610 2 жыл бұрын
@@JaviersDIY will we get only constant 5 amps or lower amps also? Will it make an issue for raspberrypi?
@JaviersDIY 2 жыл бұрын
No sir
@AyadEKorial 3 жыл бұрын
What about the heating?
@JaviersDIY 3 жыл бұрын
Just select the voltage in low heating
@dynamicsundar 3 жыл бұрын
Hi.. I’m not technical person.. I have purchased XL4015 module to increase the input 5v to 12v.. Is it mandatory to change the potentiometer and add diode in the input side..?? Please advise..
@JaviersDIY 3 жыл бұрын
For me. Yes sir. It just depend on you on what is good
@dynamicsundar 3 жыл бұрын
@@JaviersDIY Thank you so much for immediate response... For potentiometer you mentioned it as 50k ohm and for diode can you please give specification..!??
@JaviersDIY 3 жыл бұрын
dynamic Vignesh yes because the diode will protect your module from wrong polarity. You can use IN4007 diode and Up.
@dynamicsundar 3 жыл бұрын
@@JaviersDIY Thank you for the details... and one last question is there any specific reason for replacing the built in potentiometer to external 50k ohm potentiometer... Because in my case, when I tried with default setup (without the diode and external potentiometer) by adjusting the pot it should varies the voltage, but unfortunately it didn’t... my question is if I add the additional changes similar to you, will it be able to achieve my need or is there any damage in the module..!?!?
@JaviersDIY 3 жыл бұрын
dynamic Vignesh I change the potentiometer it is because the knob is very small its difficult to turn it thats why I change it.
@math3390 3 жыл бұрын
Hello, very nice video, can I use diode on OUT+ wire?
@JaviersDIY 3 жыл бұрын
Yes. You can.
@smefix744 2 жыл бұрын
Can this be connected to a 550 dc motor?
@JaviersDIY 2 жыл бұрын
No sir.
@difficommunication8315 2 жыл бұрын
can we connect 12v 6ah battery as input to this board
@JaviersDIY 2 жыл бұрын
Yes sir. You can
@difficommunication8315 2 жыл бұрын
@@JaviersDIY thank u sir🙂
@JaviersDIY 2 жыл бұрын
Your welcome sir
@alexchabanenko6347 Жыл бұрын
I can not see stable voltage under load because of your hand((
@JaviersDIY Жыл бұрын
Sorry sir. Just repeat of viewing in it
@frworld05 Жыл бұрын
Can I give 24v 10amp input power supply ,is it ok for this module for good performance?? And which diod u use?
@JaviersDIY Жыл бұрын
Both yes sir.
@frworld05 Жыл бұрын
@@JaviersDIYthanks for your quick reply. and what the value of the diod u use in this video??
@RandalloO26 2 жыл бұрын
Cant see what diode do you use?
@JaviersDIY 2 жыл бұрын
Its up to you sir what available diode you have. But make sure the diode has big number.
@sumit77194 2 жыл бұрын
Input died jrury ha lgana
@JaviersDIY 2 жыл бұрын
For better understanding please use the universal language
@sumit77194 2 жыл бұрын
@@JaviersDIY input died from me module input back voltage reason why
@shivraj9484 Жыл бұрын
Module corner hole screw size please
@JaviersDIY Жыл бұрын
3mm sir
@sumit77194 2 жыл бұрын
Sir kya wo regulater kharab ho gya ha is lay ap change kr rha ha ppz reply me input 12 volt out put 5 volt charger
@JaviersDIY 2 жыл бұрын
For better understanding please use the universal language
@sumit77194 2 жыл бұрын
@@JaviersDIY ok ji 12 volt ⚡ input together but output voltage ⚡ 5 volt connect Android mobile charger 😳 sure 100% work kra ga heat Kitna hota haaa
@swapniljoshi9997 Жыл бұрын
Potentiometer is 100k?
@JaviersDIY Жыл бұрын
50k-100k is enough sir
@NAVEENnaveen-cu3tp 2 жыл бұрын
Hii bro i am purchase this module not step up only step down
@JaviersDIY 2 жыл бұрын
Yes sir, it is only a step down module.
@NAVEENnaveen-cu3tp 2 жыл бұрын
@@JaviersDIY step up Can you do it?
@NAVEENnaveen-cu3tp 2 жыл бұрын
@@JaviersDIY Is it possible to step up if Nob is placed?
@JaviersDIY 2 жыл бұрын
@@NAVEENnaveen-cu3tp no sir
@XPRIMEMOVIES Жыл бұрын
It can convert 4.5v to 12v
@JaviersDIY Жыл бұрын
No sir. This module is actually a stepdown converter not a step up
@XPRIMEMOVIES Жыл бұрын
@@JaviersDIY ok thanks
@asageichnicht3460 2 жыл бұрын
stop the music
@jec_ecart 10 ай бұрын
Speak up. Explain. 😡
Robojax
Рет қаралды 110 М.
Jason Derulo
Рет қаралды 34 МЛН
ElectronFun.com
Рет қаралды 1,5 МЛН