This is BY FAR THE BEST video on the subject out of the 12 that I viewed! Thank you! You were the ONLY one who actually showed: 1) the tabs, 2) physically removing and installing the bulb. Great presentation; easy voice to listen to; very good camera work. Way to go!

Finally someone that shows the HID housing clips up close & how to remove the low beam. Thanks!

Thank you so much for this video! As others have said below, this is the only one that explains how to do the HID version and shows what exactly you have to do to get the bulb out. The up close video of the twisting lock mechanism with the tabs was invaluable. The view after you had taken the bulb out was super helpful as you can actually see the part you need to twist. I don’t think I would have finished this job without it, but after seeing that portion of the video, I did this whole task in about 15 minutes. Getting the new bulb in is quite challenging, but as long as you are gentle and patient, it does go back in there. It was harder with my big ass hands but I got it eventually. Thank you again!

Good sir, this video saved me over $800!!! The dealership wanted $300 for the bulb and 2.5h of labor to change the bulb. I found the bulb online for $60 and did it myself in less than 15m. Even for a super novice tinkerer, this was soooo easy with your video. Thank you so much!!

I THOUGHT I had my new bulbs installed correctly until I noticed they were dimmer than should be. They weren’t in the full way, I didn’t realize there was a locking ring. Your video was the only one that showed it and truly helped me. Once I loosened up the ring, the module slid in place and almost clicked, and then once the ring was tightened it was like night and day. Thank you so much!!

I am very pleased with the quality of your video and your clear explanation of all the steps! Took me about 45 minutes to replace mine. I did run into a frustration when it came to installing the HID. I did not realize that the whole assembly actually moves! It had shifted on me possibly at the time when I went looking for the counter clockwise clip. So, I was attempting to seat the lamp at the wrong angle. I accidently discovered that I could manually re-center the assembly manually. Once I had it back in it's original position, the bulb sat right into place. Another clue is that you can no longer reach the clip closest to the fender well because the assembly has shifted far enough to where you can't get your fingers between the bulb and the assembly. FIVE STARS for you!

My son and I spent so much time and went through so many videos trying to get the answers your video provides! I just want to add my comment so hopefully it bumps up this video and will help someone find these answers sooner. Thank you so much for thoroughly explaining!

Excellent video and presentation. Straightforward and easy to follow. Thanks for giving me the detailed knowledge and the confidence to attempt to replace the failed HID bulb in my Jeep myself.

Simple and really graphic explanation!!! The best. Greetings from Costa Rica.

Thank you thank you thank you. As others have said, out of all the other videos I looked at, none of them even mentioned the tabs to rotate that hold the bulb in like you did here. Even the drivers side was easy, removed two bolts holding the coolant pressure tank and swung it around out of the way.

This was an incredible instructional/informative demonstration.... just very on point... most intuitive (just sidestepping all potential pitfall)... thank you. Love your content...

No mechanic experience at all (dad was too sick growing up to teach me stuff outside of checking the oil, filling washer fluid and changing a tire). Your video came in clutch! Had no problems changing this pain in the a$$ bulb! Definitely subscribing for future reference 🙌🏽

Thanks for getting the camera in there closeup. That was very helpful.

great video! Mine just went on driver's side (its 10 years old), so going to replace with D3S Sylvania soon. thanks for the video!

Your video was so helpful! The only video that shows that type of square bulb and clips. Thank you so much!!

Excellent video

My headlight failed in the same way, flickered, and was turning an off-white color. I went to the dealer expecting it to be a specialty light. They wanted to sell me a $450 bulb... looked a little harder and got one at the regular auto parts store for $140. It looks the same as my other light.

Thanks a lot, very helpful

Thank you so much for getting the camera in there and showing the tabs. Only thing, I tried twisting the tabs counter clockwise but it would not budge. Is there supposed to be a lot of force to get it to unlock?There's a little wiggle from the bulb itself, but I don't want to just pull on the bulb too much.

Hello, I have made it to plugging the new bulb in but I can’t get it to go back into place. It is in the hole but it is super lose. Do you have any suggestions?

Extremely helpful for my wifes grand with the HID. Thank you man.

What about the strip part/light , can that be replaced as well? Or does the whole casing need replaced?

This the best f*cking video I seen thank you sir

This was a great video

First guy to clarify the circular clamp. Release that and it's easy button from there!

Can the signal light be replaced too? The driver side on mine stopped working.

I can not get that clamp to turn 😢 2:20

Thanks!

nice thanks man i will try this

MY 2014 Jeep both HIDs are not working , shall I change the bulbs or should I check something first before changing ?

👏🏼👏🏼👏🏼👏🏼👍🏼👍🏼👍🏼 great video.

How about the passenger side?

I will NEVER buy another vehicle with HID lights. Too effing expensive and simply NOT worth it.

Good and straight forward. We have a 19 Cherokee that the pass headlight is intermittent while in the auto setting. Everything I’ve looked up says the sensor nothing blocking sensor. Ever experience this with yours?

Thanks!