If you have a 2021 JLU or the exact same interior, read this before install. There is another step I wish I knew beforehand. You will have to do some plastic carving to make this fit. The dome light panel will not go back up otherwise. Completely remove the dome light panel and I suggest popping the dome light out first because it will fight you if you try to take it all down in one piece. Once down you will see an inner molding that allows space for the two inner tab ears of each freedom panel brackets but they don't allow for the extra thickness of mount. You have to take a razer blade and cut out about a 1/4 inch back and down to the depth of the existing cutout. Do this in a straight line until you run off the outter edge where it tapers off. You will end up cutting out a piece about 3 inches long by a 1/4 X 1/2 inch. You are basically notching out a corner of the inner molding and there are two reinforced areas under it you will have to cut as well. This will make a lot more sense when you see it. Now you will have the room to fully snap up the dome light panel back up. I love this product and would buy it again but you aren't installing this in 20 minutes ;) Cutting the plastic isn't that difficult with a new blade and a steady hand. It will never be seen and won't affect the integrity of your panel. I have pictures of what I did to make it fit if needed.

This is an excellent design.

Nice looking product, wish it could work with the Sky One Touch.

I NEED these ASAP! 😂

Dang! I just got my shipping notification from JCR for the panels. I like the no drill option. Wish I had seen this one earlier.

NICE !

The Leo Messi of Overlanding! all jokes aside great products. Will for sure be adding to my build.

Well so much for that. I got the molle panel installed now I can't get the plastic dome light panel back on. It says 30 minute install. More 30 hours.

Make a video on your m.a.s.s spare tire platform rack for the mini and the standard one ( assembly instructions)

Doesn’t look like it would be compatible with a Bestop Sunrider??

Would love to have this for my JK...hint...hint

I am having difficulties snapping in the rear plastic panel,, any hints ?

How is this for taller people? this is pretty much what im looking for just wondering how it sits

Looks like if we have (and use) the factory grab handles, they would be in the way to install your product....can u confirm?

Where is the JK option? I want it.

Do you make this for the JK?

I have 2004 LJ will these’s be compatible with my Jeep ??

Can I wear it on mytop products?

I guess this wouldn't work well if using a soft top?

During the summer I install my factory Soft top. Will this molle panel work when the soft top is on?

Does this work with the sun shades like jtopsusa or alien sunshades etc. ?

Will this work with a Bestop sunrider?

Had my oder in since June 26 and they say it is still at powder coating. :( They say it is out of their control when it leaves their hands.

Is there enough headroom clearance to mount a radio?

So after watching I have installed correctly, but it makes alot of noise when flexing through off road trails...is this normal?

I'm a little confused. Why did you remove the two tabs, just to put them back in place? Was in needed to fit assembly in place? Great looking unit, I will get one for sure, THANKS, SKIP

Does this fit a Jeep Gladiator Willy's 2022. ? What is part number and website? Other models show need to do drilling.

Well I tried to order this direct from your website. Did not give me an option to ship. I then tried to message you through your website and never heard back. I'm guessing you don't ship to Canada nor respond to questions from Canada.

it's to bad it doesn't work with any handle options.

Does this work on 2024 JLUs?

Is it not available anymore?

Will this work with a soft top

On back order like everything else is I suppose too. The JCR one looks better too. And why can't you guys include black hardware so it blends in.

Don’t use these, I got mine and the QC is awful. Edges are all burred and spacers are falling apart out of the box

People are really convinced to spend $50k on a CONVERTIBLE truck and then do everything they can to diminish the effectiveness of that capability. 😏