Video covers the removal of a Jeep Wrangler TJ gas tank. This is recommended for the installation of the Taboo Customs Jeep TJ rust repair kits. Visit us at www.taboocustoms.com to get your rust repair kits.
Пікірлер: 58
@mikehartmann51872 жыл бұрын
Good video. Two additional points - look for an attached ground strap on the filler nozzle, and if it’s still there, disconnect it before you drop the tank (if it’s missing, replace it to avoid static discharge when you’re at the pump). Once the tank is off the Jeep, inspect the filler nozzle for rust. If it’s rusty even a little, remove the filler nozzle, de-rust the part and repaint. The reason for this is you can’t get a new filler nozzle, and since it’s a part that often rusts out, you’ll probably have a Devil of a time finding a replacement at a wrecking yard. Better to keep the nozzle you’ve got in top shape so you don’t have to deal with that issue.
@JeepGarageCA Жыл бұрын
Excellent video and was bang on perfect to help me get my TJ tank a skid plate off and replaced. I never would've figured out the electrical connection since my red tab was more brown and VERY stuck.
@davidshettlesworth144210 ай бұрын
Thank you for this excellent educational video. I appreciated the additional cautionary notes on the bolting of the tank back in place. Carry On Sir!
@christophermerrill3859 Жыл бұрын
Thanks for the tip on removing the wheel for better access to the tank connections. Seems obvious when you say it, but I probably would have struggled to reach them from under the tank for 15 min before figuring it out myself :)
@TabooCustoms11 ай бұрын
Glad it helped
@fishinjunkee17012 ай бұрын
I dont know how you got that electrical connection off so fast ? I have been out in the garage for three hours trying to get that freeeeeekin thing off. Holy crap I cant get any of them off 😂🤣😂 You make it look waaaay to easy
@TabooCustoms2 ай бұрын
I'm going to do another one sometime here in the near future I'll have to show that up close. They can be a major pain. Often I'll use a small screwdriver to hold the tab down then wiggle the connectors back and for the try to break the seal.
@scottstewart2376 Жыл бұрын
Awesome video! Exactly what I needed for my project tomorrow. Thanks!!!!
@jasoncolette85983 жыл бұрын
Thank you for this. I enjoyed it. Very informative. With very good descriptions. I am about to tackle this job. I recommend this video for anyone looking to diy a fuel pump/tank replacement.
@TabooCustoms3 жыл бұрын
Glad it was helpful!
@pete6996692 жыл бұрын
Thanks buddy. And that jeep in the background is freaking killer!!!!
@jodymcleod46363 ай бұрын
Excellent instructional video. I did the same thing with the rear diff vent hose removing my fuel tank. Had a good little laugh about that. Great job!
@dragonsbreath19843 жыл бұрын
Informative. I’ve found that the tank is in the way of removing the T55 bolt that mounts the rear track bar to the axle. But I’m also replacing the fuel pump and skid plate, so there ya go.
@meinbherpieg47232 күн бұрын
You rock sir. Thanks
@williamvega-rondon63843 жыл бұрын
Great video , guy knows what his is doing simple and straight to the point!!!!!
@TabooCustoms3 жыл бұрын
Thanks, happy you enjoyed it.
@paultrendell1815 Жыл бұрын
Exactly what I needed, thank you!
@mattwilliams87333 жыл бұрын
Great video! Great info and descriptive! Gonna drop the tank in my 05 to fix the valve in the tank that sticks either open or shut.(mine is open) (Future video suggestion. Y’all did great, it would be awesome to know the socket sizes we need going into the job, obviously that’s being picky and spoiled 😆. But still, it’s nice going into a job knowing the sockets we will need lol)
@climberdad Жыл бұрын
Second time watching this video. Very helpful! Thank you
@basherpierce29472 жыл бұрын
Good video, thanks for showing where to unplug hoses and wire, didn't know that you could get to them by taking tires off, other videos I looked at , showed dropping and then unplugging I am using a motorcycle jack to replace mine, seems to be sturdy
@TabooCustoms2 жыл бұрын
Glad to help
@hhyperdd3 жыл бұрын
Thanks! Great video with minimal window dressing.
@TabooCustoms3 жыл бұрын
Glad it was helpful!
@Soothsayer-rs5nb3 жыл бұрын
Great video ...thanks
@TabooCustoms3 жыл бұрын
Glad you enjoyed it
@generaldrz3 жыл бұрын
Thanks for the video I'm about to drop my tank to repair rear frame
@TabooCustoms3 жыл бұрын
Glad I could help
@mjs97102 жыл бұрын
Thank you great instructions
@TabooCustoms2 жыл бұрын
Glad it was helpful!
@johnfink9021 Жыл бұрын
Great video Ty
@TabooCustoms Жыл бұрын
Glad you enjoyed it
@Lovemyamericamyhome Жыл бұрын
Thank you
@reallycoolname61242 жыл бұрын
Takes me back,just filled my tank my strap broke and I'm driving down the road with a stream of gas luckily I pulled in a station luckily there was a junkyard near me with the same make and model I picked it up and changed it and went on my way
@johnmurraycompton5692 жыл бұрын
Really appreciate this tutorial. I'm about to drop my tank to repair some rust holes in the rear cross member (not where the bumper mounts, where the rear of the tank skid mounts). The holes are on each side of the member, close to each frame rail. Because I appreciate this vid so much I immediately checked out your website to see if you have a repair kit. Might be something you want to offer in the future. Could use it for my LJ. Thanks again for the vid!
@TabooCustoms2 жыл бұрын
Thanks, we have designing a rear TJ crossmember on our list but not sure when we will get it done.
@johnmurraycompton5692 жыл бұрын
@@TabooCustoms Nice! Since my last post I've learned the LJ's have an EXTRA cross member that the regular TJ's don't have. I was WONDERING why it was so hard to find a replacement. Could be an opportunity to be the one shop that supplies them for LJ's. Thanks again!
@OntarioFreshwaterFishing3 жыл бұрын
Good video. I'm going to be putting a fuel cell in the back of my Jeep soon and was wondering how to remove the stock tank.
@TabooCustoms3 жыл бұрын
Glad it helped
@traavdasav3 жыл бұрын
Thank you Going to drop the tank on my yj because some old nasty gas
@TabooCustoms3 жыл бұрын
YJs can be a little tricker, partially due to age and rust. The leaf springs add some extra hassle as they some times keep the exhaust from bring able to go over enough.
@chevas911872 жыл бұрын
What size do you use to remove. 12mm
@ujayet3 жыл бұрын
Was hoping I can do this at my home.. but looks like I'm going to need to take it to shop ugh...don't have jack with special plates support..dont know why a 98 wrangler have the fuel filter inside the tank... a dumb design.
@nordland22353 күн бұрын
My tj feed line from the fuel pump to the hard line broke....what part do I need to buy....part# ?? my tj has a 6 lift.
@TabooCustoms3 күн бұрын
I'm not aware of a new off the shelf version. You can find used ones on ebay. Or you can go to Napa or another parts store, get the fuel line ends, some fuel injected fuel line and some good clamps.
@VJ-xn9gh3 жыл бұрын
Do you have a video showing how to replace the front bolts for the fuel tank (on is sheared, one just spins) 😞😢
@TabooCustoms3 жыл бұрын
Sorry I do not, I believe those are weld nuts up on top of the crossmember. I would probably see if you can cut the one that spins. Then hopefully you can drill out the sheared one and have enough room to get a nut on top with an end wrench. If you dont have enough room you can loosen body and raise it up. But chances are the body mount bolts will give you issues. Another option is to drill holes in the tub to try to get a socket down to the nut on the crossmember. To do that I would start with a small hole so you can see if you might have to adjust the location. Then drill a larger hole, just make sure you can get a plug for it.
@bonniekeating95653 жыл бұрын
@@TabooCustoms Yes that is exactly what you do for this. Hole saw and rubber plugs.
@edwardnigma65682 жыл бұрын
The best rust repair kit is demanding that your local government stop spraying the roads with a metric ton of salt every year. I live in a place where it snows and freezes like crazy for almost 9 months, we dont use salt and its still only dummies who slide off the road and crash.
@coconutoperator92417 ай бұрын
How long did it take to replace the tank? From start to finish?
@TabooCustoms7 ай бұрын
If nothing goes wrong and you know what your doing, an hour.
@bonniekeating95653 жыл бұрын
What year is the Wrangler TJ ? I have a 1998 w/4.0L and its impossible to find a replacement gas tank for that year. You forgot to mention "bleeding of the Fuel Injection Rail. There's a cap on what looks like a tire valve. Let fuel pressure off there. Some say just taking off the gas cap relieves some pressure but I don't buy that. By your plate Illinois rust belt my friend. I'm here in Dallas Texas. My 1998 TJ has been siting 10 yrs now. Two tires actually blew from dry rot. On concrete slight nice surface rust on hood /body. Underneath again light surface rust for 20+yrs old. Overall it needseverything Cat was rattling, Clutch need replacement (original 180K) AC shot. bypassed with different belt. Brakes original untouched in rear I was starting it and driving around the block then came the the day no start. The usual happens life , no funds etc etc. So I was starting to build a game plan to try to start him. Tank and lines are probably just varnish gummed. but can't find a new replacement tank anywhere. Seems to be a couple pumps available what's the different one for 4.0L the other for 2.5 L. I think 1998 was 15 Gal Tank for both. Any suggestions ?
@bonniekeating95653 жыл бұрын
Dumb just read below its a 1998 you are working on ! Yeah skid plate replacement no problem. So looks like nothing on a 98 Gas tank replacement. So have to clean with Evapo-rust and seal line with Kreem. Dumb question is the tank plastic on the 98 ?
@TabooCustoms3 жыл бұрын
This is a 1998 TJ. As far as I know there isn't any difference between the 2.5 to 4.0 fuel pump as far as volume and pressure.