One of best step by step descriptions I've watched. Thumbs up to you
@sludgetrudger Жыл бұрын
Thank you for the video. Just ordered 10 Factory rears for my 08 JKU. Just installed 10 Factory front assemblies last summer and love them.
@rodtoler6 жыл бұрын
Good video, Brother. Very thorough. As you know, I replaced Becky's rear axle shafts with Chromoly last year. I was lucky to have zero hiccups. The wheel sensor gave me a struggle on one side. Otherwise, easy-peazy-lemon-squeezy. It only took about hour to do both. That included the learning curve on the first axle. Looking forward to more informative videos.
@HWoodCreations3 жыл бұрын
Im about to replace my seal and bearing as well. I didn't realize replacing the entire axle shaft assembly is less than 300 so I may just using it as an excuse to upgrade the axle. Good vid!
@surfdogdude3 жыл бұрын
Awesome! Loved the idea of using the rotor to get the axle out. :)
@reytech1786 Жыл бұрын
Amazing video, straight to the point, thank you ❤
@sethlonmier56576 жыл бұрын
Awesome thanks! Very helpful step by step
@EVH5150iii3 жыл бұрын
I don’t even need new rear axs but I still watched the whole video, very informative
@igorgromov23572 ай бұрын
I'm doing this now. If any of the pressed in bolts spin through, no need to weld. Use a nut splitter where fits to break the nut but I ended up using a metal cutting wheel to cut through part of the nuts all around, spray some PB blaster, comes right off. Just did 3 of them.
@sambrimly44746 жыл бұрын
Thanks! I have a bent flange on my 2013 JKU
@louisdiaz195 жыл бұрын
Hah. "Trying to get to about 1,000 followers by the end of the year" and now you're at 12.4K. Great video. My rear wheel bearings are bad and I'm considering replacing the shafts as well while I'm there.
@JKGearandGadgets5 жыл бұрын
Haha I know it’s crazy! And yes I highly recommend just going with a set of chromoly shafts while your in there, a little more pricey but it’s a great upgrade
@markbellger89456 жыл бұрын
I’m assuming chromoly shafts are stronger? I’d like to upgrade my Rubicon but don’t want to go with an entire new axle
@rayss33234 ай бұрын
Great vid. I need to replace my e-brake shoes and thought removing the axle would make it easier. Nice!
@mercurial94pro4 жыл бұрын
Was your bearing squeaking driving down the road at all before replacing? My rear passenger side squeaks, its not the brakes I’ve replaced them and squeaking noise still there. I plan on doing this soon.
@stevenstrack55944 жыл бұрын
Where did you get your axle shafts with the bearings already pressed on?
@donlittle00033 жыл бұрын
Great video didn’t take long!
@jameslainhart1907 Жыл бұрын
Great video! My wife has a 2015 unlimited Sahara. After months of trying to figure out why the breaks were noisy and it sounded like the AFLAC duck every time she turned right, I’ve come to the conclusion that is definitely coming from the rear end. I’m considering replacing the axle shaft assembly’s. I’m hoping it’s not the diff. Have you ever gotten any weird noises due to this issue?
@Jake-ci1ld Жыл бұрын
What does he mean when he says make sure the jeep is in gear and take the ebrake off wouldnt that cause his jeep to roll off the jack stand?
@Missbirdd2 жыл бұрын
You sound like Chris Pratt. So this was fun. I imagined Emmet from the Lego movie making this video. 🤣 Very informative. Thank you.
@bryankrall83025 ай бұрын
Thanks for the brake rotor tip
@jermainemccall2054 Жыл бұрын
Hey bud what rear Axle I need for my 09 jeep Wrangler ?
@rickwhoo12 жыл бұрын
Was your parking brake cable attached??? Those shoes looked pretty rusted too...
@aidanparker95436 жыл бұрын
Hi im actually watching this because I need to replace my parking brake. I have a 2008 jku as well. Somehow it blew up and destroyed my abs sensor and itself. Have you replaced a parking brake before or do you know how to? im thinking I have to take the axle soft out and assemble the brake on the ground. its freaking impossible to get the return springs on the brake, theres no room. If you had any pointers that would be great. thanks man.
@JKGearandGadgets6 жыл бұрын
I have never messed with the parking brake before, sorry. I wish I could help though!
@tomsteel88644 жыл бұрын
Great video man, thanks! I’m good to go after following this. No more bent flange squeak.
@liamstoddard67093 жыл бұрын
I have an odd question. I have a 2015 Sahara x with the factory rear locker. Do I have rubicon shafts or sport?
@JKGearandGadgets3 жыл бұрын
Are you sure it’s a factory locker? Or a limited slip? Do you have the factory electric button for it?
@AceGoodheart3 жыл бұрын
Does the ring and pinion gear need to match the splines on the axel? Let's say you had 32 spline axels and then switched to 35 spline. Will this be okay without changing your ring and pinion gear, or do they need to match? I'm a newbie at this so it's probably a dumb question.
@MarkRenouf2 жыл бұрын
Yes, if you upgraded just the carrier to accept 35 spline axles and keep the same gears, should be fine. Usually the gears are upgraded at the same time to lower ratio... but that's not required.
@jasonkus50786 жыл бұрын
Are the axles different because of the e-locker? I bought a 2017 jku sport and plan on putting in pro rock front axle. I didn’t know the rear was different from a rubicon.
@JKGearandGadgets6 жыл бұрын
Yes, the Rubicon rear axle is 32 spline with different length shafts because of the locker. The sport and Sahara have 30 spline shafts and are equal lengths on both sides.
@JKGearandGadgets6 жыл бұрын
And I would recommend looking into the fusion4x4 44/60 hybrid front axle. Close to the same price as a Prorock 44 but is a better choice hands down
@robertpc1004 жыл бұрын
Does your Jeep have a lockers.wondering if I can still pull axle straight out since I have a locker set up
@JKGearandGadgets4 жыл бұрын
Yes, and you can pull it out with or without lockers.
@joecory41103 жыл бұрын
Good through but concise video
@franciscotavarez41385 жыл бұрын
Hi amigo l,have jk rubicon 10aniversary, l changed axle shafts ,,38 "tires,,,titro o ten factory,,recomendé, one ,thank you
@timratliff61386 жыл бұрын
Are the driveshafts on a 07 2 door x and a 17 comparable
@JKGearandGadgets6 жыл бұрын
Yes they are exactly the same
@geefim2144 Жыл бұрын
So it makes no difference if it’s the rubicon with locker ? Going to attempt this soon. I read where since I never pulled them out before you will need a slide or the rotor method
@JKGearandGadgets Жыл бұрын
Rubicon has shafts with unequal lengths. Standard base axles are the same length.
@JKGearandGadgets Жыл бұрын
This jeep is a rubicon
@tedhargiss10566 жыл бұрын
What happened to swapping out the axle assemblies with the Ford 1 tons?
@JKGearandGadgets6 жыл бұрын
I started to work on them but I’ve had other expenses come up, so those got put on the backburner. I’ll be sure to post up some videos once I start working on them again
@tedhargiss10566 жыл бұрын
Gotcha. I'm swapping out the rear end of my TJ with a Ford 8.8. Was curious to see how you performed it.
@thekrakensquestforb.o.h36503 жыл бұрын
How do you confirm the axle shaft is bent or the flange is warped
@williamstachewicz9649 Жыл бұрын
I seen mine by simply breaking it down on a jack to the axle it's self and throwing it in gear ⚙️ lmao 🤣 make sure both tires are off the ground ofc and step back see it your axles are wavy
@rodolfow.campos6605 Жыл бұрын
Hey question! So the rubicon axel is one smaller than the other and the the unlimited sport are both the same size?
@JKGearandGadgets Жыл бұрын
Yes
@rodolfow.campos6605 Жыл бұрын
@@JKGearandGadgets I have a 2007 unlimited X, I purchased the “corresponding Axel” by the book and with the vin number. but when I got the replacements, they were the same size but my jeep has one axel longer than the other.. the rear passenger is smaller, so apparently the rubicon is the one that fits my jeep right? Or witch one do you recommend? Please help me with that! My jeep has been standing for almost 6 months! I can’t find the right one. 😩
@joshua7999 Жыл бұрын
How did you know the flange was bent? Wheel wobble? I put on all new brake pads and rotors and I think this is happening to me because of the noise it is making.
@JKGearandGadgets Жыл бұрын
You can Jack the jeep up and put it in drive and watch to see if the flange is bent
@derekhartman66006 жыл бұрын
Go Team Rugged!
@kylewesner246 жыл бұрын
Go Team Rugged!!!
@timratliff61386 жыл бұрын
If I put 8t back together and the sencor does not completely cover the spline would that throw me abs lights....
@JKGearandGadgets6 жыл бұрын
Are you getting an abs light? What all did you do?
@timratliff61386 жыл бұрын
Both wheel bearings and seal...now I get the abs lights on I noticed the sencor on the other side covers the whole tone ring but the passenger side only covers half or so....do I need to take it and get pressed more
@JKGearandGadgets6 жыл бұрын
It could be, is the sensor mounted flush?
@timratliff61386 жыл бұрын
And both axles are same size correct?
@timratliff61386 жыл бұрын
I'm sure there flush...if cleaned both rings plus bought 2 new sensors
@jesus_58486 жыл бұрын
Go team rugged!!
@WATCHTHISSHITCARCLUB6 жыл бұрын
Go team rugged!
@keithlargy82306 жыл бұрын
Are those 37s?
@JKGearandGadgets6 жыл бұрын
Yep!
@africolouis7769Ай бұрын
You did a great job man congrats ❤this heart doesn't mean I want to marry you it's for the video sorry Im a straight guy
@bryanbarbiea51632 жыл бұрын
the outer axel bearing race should not move by hand. it should press into place and also need a puller to remove. if you can remove it by hand the axel housing is worn.
@devinscott59886 жыл бұрын
Go TEAM RUGGED!!!!!!!!!!!!!
@AZWESTSIDEWHEELERS6 жыл бұрын
Go team Rugged
@acoustix66 жыл бұрын
Go Team Rugged
@VBS7026 жыл бұрын
Go team rugged
@gregoryhowell6 жыл бұрын
Go team rugged.
@joebishop79096 жыл бұрын
GO TEAM RUGGED
@edc4lyfe4456 жыл бұрын
Go team rugged OIIIIIIIO
@punknjl87226 жыл бұрын
cant hear sound
@JKGearandGadgets6 жыл бұрын
Lou Smith don’t know what to tell ya, my devices are viewing it fine as well as other peoples
@punknjl87226 жыл бұрын
Yep, weird. works on my phone fine. Just not my computer. Thanks fro the reply
@punknjl87226 жыл бұрын
Got it sorted out. great video man. Love your stuff.
@MeowMeow989457 ай бұрын
Dear Sir,We are Amazon sellers and have recently launched a new product. We would like to place the product link under your video. Can you cooperate wth us? We can send you products for free.
@ia.m.62135 жыл бұрын
Quit your yappin' and get to the point, man!
@JKGearandGadgets5 жыл бұрын
What are you talking about? Sorry for going into detail on certain topics. It’s all useful info.