That was a good attempt! But there are some issues that stop it working. The tank must have no air in it , the air getting in stops the suction, also no air in the intake pipe put a one way valve at the bottom of this pipe to stop water running out once it is full. The diameter of the outlet pipe must be bigger than the intake pipe, the weight of the water falling out of the big pipe is what makes it suck water through the smaller pipe. The outlet pipe must be very very long ( much longer than inlet try several meters longer) and on a slight angle down, add a reducer pipe at the end of the outlet pipe. Lift the tank up very high above to increase downward flow of water, fast speed out greater suck . to stop air coming into tank from outlet pipe put in a stand pipe that is taller than the tank( put T joint into outlet pipe), if any air burps back up it will go out the stand pipe. I hope this helps

My friend, Only yesterday I somewhat was successful in my attempt with the free energy water pump system at my five year old daughter's science fair after spending 6 very difficult days in my experiments. One of the many things I learnt ( by God's grace), was that it is very important to include a large enough air trap just after the exit of the outlet. By doing so, the air trapped in the tank will have an immediate escape route which will help the water to flow a little more freely. The air trap will also build up a back pressure when it is full, which in my openion ( and the openion of a few others) help add more pressure to the flow. I'm am still to work out the science in this regard to improve the system, because like you, I'm also very anxious to see if this system can really be of a help to my community here in Guyana. I live in a small town call Lethem.

Thank u po sir sa informative video👏

This was a great try. It is important to see failures as well as successes. Thank you

Thank you for giving us good idea in farming

Kulang yung design mo paps. Lagyan mo ng isa pang valve yung lower part ng suction pipe. Tapos pag priming, kailangan punung-puno pati yung suction pipe mo puno ng tubig. So pag open mo ng valves, halos sabay dapat yung sa outlet and suction pero mauuna ng konti yung sa outlet. Also, yung height ng tanke mo will play a big role. Kailangan mas mataas para mas mabilis ang velocity ng tubig when going down. This will generate a stronger vacuum. Ok na yung demo mo sa transparent jug ng mineral water kasi nag-vacuum sya. Kung puno sana ng tubig yung suction pipe mo tuluy-tuloy na ang higop nyan.

painta76 is correct, there should be no air in the system and the suction pipe should be full of water too. This can be accomplished by putting a foot valve at the intake. This system can lift water at a maximum height (head) of 6 feet (measured from the level of water at the reservoir to the height of the intake outlet. The 6 feet is computed from the standard atmospheric pressure of 14.7 psi at sea level. Make it less than 6 feet for more flow. Thank you Julius for sharing your knowledge and experience with us.

This is a good channel.. Helping those of us not to do the same mistake..

salamat prof for sharing your experience..as the saying goes experience is the best teacher!

Thank you for sharing sir

Salamat sir idol kagulay! More power to you... God bless! 🙏🎉😊🤗

Thanks bro for testing and proving it

I was reading comments, and I can't help but make my comment too.. This setup falls under the so called siphon effect and this setup will never work. This setup will not be able to produce enough pressure to lift water, airlocked or not.. Water can only free flow from a high level to a lower level, unaided by a pump. I hope I can share the link to the explanation why this setup will never work, for the benefit of everybody.. Appreciate your effort though sir, in always sharing your ideas and expertise that might help our hydrophonic community improve our craft.. thank you always sir.

Wow! Amazing

Congratulations brother. The truth fighter.

You are very right, I do it my self twice with deferent size of PVC with negative results.Water always find it's on level. Instead I interconnected all my 5 200 ltrs blue drums with siphon system without making any holes below the drum for my rain water storage. Thanks for your honest expensive experiment.

Good idea sir., But I think it will work,. Pahabaan mo lang ang exit ng tubig,. Para malakas hatak or vacuum.. Sana makatulong

Oh, and nice music too! Thanks!

Thank you Sir,about your sharing

To lift 27 3/4 inches or 70.5 cm of water at sea level you would need 1 PSI (pound per square inch) of pressure. The higher the lift height, the more PSI you would need. It's better to use a smaller diameter INLET pipe. The discharge or OUTLET pipe or line should be LONG to maintain internal vacuum and capillary action, larger in diameter, and bushed down to 1" at discharge point. Add 2 expanding columns f same height & downstream of your 60 gallon drum to facilitate pressure surge. Discharge point should be lower in elevation. If you want to draw water from a deep well, I don't think if would work. Best If shallow well or SURFACE water like pond or lake. Also try ram pump method.

prime the pipe coming up to the bucket....then fill your bucket all the way up until the water is coming down into the top pipe....make sure all pipes are filled with water and bucket is all the way full. i havent tried it but its what i was going to try differently. same idea as fuel line on a car or break lines needing to be primed so theres no air in the lines. Im going to try this to draw water from our live springs. Good job on yours....dont give up.

Great job kuya👌❤️. I love your gravity pump

Sorry for waiting guys. hope you learn a lot from this episode. Thank you

Sir try nyo pong i-search itong TITLE sa sa youtbe "No Motor No Electricity Non Stop Water DIY......it works po....

Ha ha ha very much thank u for sharing I was almost buying some materials to do that pump with out electricity thank you for sharing. Now i have to buy da real pump to irrigate my farm thanks again

Ok heto na nakita ko na po hinahanap ko na video nio Sir Julius. Thanks po for sharing your knowledge about farming. 👍

your video is awesome

I think it will work bro medyo kulang lang yung pag seal ng pressure. Napansin ko walang check valve sa ilalim ng pipe papuntang input ng tank

Nasubukan ko na Rin to idol, sa napanood ko SA KZfaq dati pero malaking scam 😁 napagastos lang Ako salamat sa pag upload for awareness

Salamat brod, for trying. Its a learning experience... your new subsi here.

try to have all the pipe filled with water, use foot valve for intake, be sure that the volume of water inside the container has enough pressure to siphon the volume of water inside the intake pipe to a certain desired height

Saw you on Dexter’s World. That was a nice jester helping him out. I’m thinking of installing a unit at my farm in Mindanao.

Try putting a back flow valve and remove all the air inside and also make the tank as strong as it could be, to counter the atmospheric pressure from the outside, and also build up the vacuum pressure in the inside of the tank... Yhanks

good day , new subscriber here, i want to learn more about this

pag alaga ng atim ay related sa food. about food kami at informative to na video, thanks

Great try! Could the issue be that the pressure in the tank is not enough to pull up the weight of the replacement water? If you increase the down pipe size and constrict the up flow pipe, the rate of water leaving the tank would increase and the speed of the up flow pipe would increase to achieve the pull needed?

1 of the possible issue that I noticed that caused the operation failure is that you must eliminate the air on the system. The intake vertical pipe should also filled with water prior to operation

Karamihan na napanood ko ma's maliit yong humihigop na LBC tubo at yong outlet ay ma's malaki.. At meron silang kinakabit na tulong sa pressure katulad sa ram pump..

Hi, the universal law of water flow is that water moves from higher potential energy to lower potential energy of water in the tube. When i was examining your set-up I was pretty sure that it is not going to work because there is no potential energy difference at any point in the system once you close the valve on top of the container. I am a soil water physicist, Eduardo P Paningbatan Jr., PhD. an allumnus of Katipunan National Agricultural School (now JRMSU). Also, I have developed a backyard hydroponics/ aquaponics systems that does not require electricity, which i will be glad to share to you this coming Dec. In KNAS allumni Home Coming.

Good day sir julz Gumawa din ako ng ganyan system dahil nga sa mga napanood kong video para sana sa aquarium namin. Pero talagang ayaw nga umakyat tubig sa taas. Lahat na yata ginawa ko. Nilagya n ko pa ng footvalve sa inlet vacuum at check valve sa discharge para hindi bumalik hangin pero ⁰ayaw pa din. Nagtry din ako na lakihan ang discharge line at maliit ang vacuum inlet para mas malakas sana ang vacuum pero wala pa din.

You put some pvc vertical between outlet and tank for air pressure,and put foot valve to hold the water

It can be workable if the outlet pipe is bigger than intake with long enough then put reducer at the end with same dia. at intake and container must be airtight.

Dapat sir try nyo lagyan ng checkvalve sa intake galing drum para oneway lang ang flow ng tubig tapos punuin nyo ng tubig ang drum na nasa taas bago nyo pakawalan ang tubig. sigaduhin walang hangin para derecho o walang putol ang daloy ng tubig.

Sir Juls itry mo rin po ang gravityfeed water system sa nft malaking tipid sa kuryente wala pa kasi akong nakita kahit isang youtuber na ginamit ang tech na ito sa vlog nila puro kc timer ang gamit karamihan

You could try using a Heron's fountain

Salamat sir sa info, nakita ko rin yan s ibang yt channels and i think maganda syang gamitin for s nft sana. Nd ko pa sya natratry kc nsa krutky p lng ako, at ngtratrial n makapag patubo 🤣🤣🤣, pero anyway, maraming salamat s video nyo po.

I also made a trial but not succesful. I think the container's flexibility vs vokume also play some role in making the suction pump work. I use a 10L container but is to rigid and the water volume that comes out initially is not enough to induce a vacuum effect that enable it to suck water from the source.

Galing mo dol

dapat sir may check valve yong suction pump para punoin mo muna ng tubig yong pipe para pagbukas mo may tubig na kaagad..

Thank you for sharing your failures. It helps alot. To everybody and learned from the good comment. Shared 😅0:08

Symphonic principles just eliminate the air in the container once the correct ratios of water out (discharge)and water in (suction) it will create to much vacuum to the container causing to damage. Im planning to do experiment also to drive a ram pump so you can transfer water at certain elevation.

The diameter of the lower pipe shoud be at least double size of the top pipe depending on the height difference and vacuum, you can check the ram pump principles as well, it is possible but it still needs a bit energy or some external pressure in the return pipe to have a good efficiency

Dapat po sir un tangke nyo puno ng tubig,, at un inlet at outlet pariha po may luck,, pag napuno nyo po un tanke isara nyo make sure na wala pi hangin mkakapasok,, sa start una nyo po bubuksan ang outlet kasunod nmn po ang inlet,,, seconds lng po dapat ang pagitan ng pag bukas sa outlet at inlet

Another thing if you live near river or a decent stream of water you can use a air ram water goes in the front fuel check valve and up to a bubble an air bubble and when the pressure equalizes in the air bubble it shuts the first check valve off and then moves water through another check valve you can raise water up to 60 ft in the air you don't use the water directly in the hydroponics or aquaponics system you just use it as a power source to run your water pump and it runs 24/7 365 go on KZfaq and look up air ram you can make them yourself you might be able to even use used one to pump water up in the air and as the waterfalls down through the old-fashioned charging system that uses loops or 10 cans the generate static electricity high voltage you could even charge a battery

Brod Subukan nyo yung Isang Tubo sa Baba ng TINBA na naka LUBOG din sa TUBIG!!!... ng MALAKING DRUM!!!...

kindly observed the big pvc pipe, now he put air do you think the air pressure will not pass through the big pipe?

Bro suggestion ko lng bka sakali magwork, di nman need n bilog ang vaccuum tank mo try mo kya square acrilyc sheet parang aquarium para di cya nayuyupi sa vacuum them mas malaki dapat outlet pipe kesa inlet pipe, ex.1"outlet, 1/2"inlet at yung level ng putol ng pipe sa inlet at outlet di lalaki sa 1 foot ang distance, at dagdag check valve sa outlet para di mg back flow ung hangin, ang gastos neh😅 masasagot nman curiosity naten heheheh

Can i give a helpful idea? I suggest you must attatch a foot valve from that siphone tube or return and a valve to fill water to avoid air presence from the circulation that makes the vacuum pressure loosed and maintain it's vacuum strength.i hope this will be a helpful comment.thanks for your time.

We have to follow the nature rule water move from higher point to lower one , the pressure crate in the tank is not strong enough to suck the water up to fill the tank , it sucks the air in instead . Remember energy can not be seft created , it tranfer one form to another ,

nice shirt daga

Wilkins bottles gamitin mo kasi matigas yon..para di mayupi..tnx..

Done it with 1.5L softdrink bottle sir, I think little adjustment lang cgro kulang sa

You need the tank and all the pipes full of water with the air gone from the system before you open the drain pipe to start it, the drain pipe also needs to be under water.. the pipe at the top of the tank is too high up, it also needs to be under water before you open the drain... Its a good idea, keep trying..

Dapat lagyan mo ng valve sa suction pipe.

Thank you bro for being honest of your trial and error experiment..some vloggers do it the same but it also fail..

madami dami nang naloko sa idea na yan. isa lang sagot dyan, atmospheric pressure. kung gagana yan, himdi maiimbento ang water pumps :)Ramp pump na lang gawin mo boss, pwede pa hhhih

You must improve Suction portion of your pipeline . Elbow fittings loose the velocity of water. I suggest, you willl use 45 degrees or 30 degrees angle.

Pwede ako mag share ng idea. Baka ang problem yun pipe ng suction kailangan meron water para hindi hirap ang pressure requirement to suction.

I watched many videos of that system and I observed that there should be some factors to be satisfy aside from the size of the pipes which depends also the size of the water tank to be used it should be the water tank along with the inlet pipes which dont forget to connect a check valves on the end which was to be submerged on the water source, the water tank and the pipes will be completely full of water and no air inside and supposed to be hundred percents no leaks for the water thats why they used always solvents to properly sealed both the tanks and the pipes in your demonstration if I m correct you never removed the air in the suctions inlet pipes by putting the water inside and attached check valves which is the most important so that no air will penetrates inside the inlet pipes.If there is presence of air inside the Inlet Pipes and Water Tank the principle of Vacuum suctions will not work because a "GAP" or SPACE will be created inside whether in the tank or in the inlet pipes so the "CONTINUITY OF ACTIONS" will not be done.

I've tried and it is successful but only for a few hours before at some point micro sippage of air gotten it loss suction. And eventually you have to prime the tank again. There are many other technical factors to consider to on one way anti-back flow principal as well as proportional ratio between the suction and discharge.

Did you fill the return line with water before opening the valve ? If its full of air it wont suck.

Yesss... I made it too 😁

Mukang nakalimutan Mo lagyan Ng check valve Yong dulo Ng panghigop Ng tubig na pipe sir... Para Hindi bumalik ung tubig pababa... Baka maging effective un .. saka pinopuno Ng tubig ung pipe Pag may check valve Yan para ding paggawa Ng puso Yan ung dulo Ng nkabaon na tubo ay may check valve para ung nahigop na tubig ay di na babalik...

I think you should try it again. You are trying called drum pump. I saw a video with AgriBusiness Channel using Drum pump and Ram pump

simple lang hanap ng iba, to see is to believe. sana ipakita din ng iba ang gawa nila na tunay ngang gumagana ang gawa nila.

I still believe that system can work. I think there should be a minimum ratio between top (vacuum space) and bottom (water / pressure). Use a taller container. The shape of the container may also affect. A diamond shaped container maybe the optimal, with the height ratio of 2:10. Since the system rely on gravity, You need the right amount of water in the container to create a vacuum at the top to suck the water in. And at the same time water creates pressure at the bottom to push the water out. I really wanted to test this system, but cant do it in my place right now

i just found your channel. done subscribe.

I'm not sure if it will ever work, but maybe if you have some sort of non return at the bottem of the suction side that does not cause to much restriction for water flow and also try to prime the suction pipe before sealing the top so that it does not have to suck alot of air before the watter, it might reduce the amount of suction pressure needed for the water to travel al the way to the top. Don't know all the physics so don't be disappointed if it doesn't work. Good luck with the farming.

sir wala pa akong exprnce sa pagtatanim ng lettus ano pong variety ang pwding itanim ngayon ber month?

Then one more thing, dapat Puno talaga yung tangke ng tubig para walang hangin na papasok. As in puro tubig lang dapat. Hope it helps. God bless

Dapat duha imu stand pipe dyan sir para sa air para di ma yupi ang galon..

Make the size of pipe for discharge is bigger than the pipe on suction.

I think maybe a larger diameter pipe on bottom. And smaller pipe going up. Would be more weight pulling. I think 🤔

a lot of you guys thinking about "we need solid container for that" but before we try things about "free energy" we must consider 4 things... trust me, I'm an engineering student 1. energy cannot be created nor destroyed, it transforms from one form to another 2. we must learn simple hyraulics... when it comes to liquid system, we need hydraulics knowledge or ANY HYDRAULIC BOOK for beginners 3. try to sketch out first and from the sketch, analyse some things about water flow, pressure, weight, etc., also consider things about air which "air is more compressible and decompressible than water" 4. consider gravity and weight always fall downwards I hope, I can make a video of this and explain the basic hydraulics in this system

Hi use tee at the input point and not elbow and above it a ball valve to fill water to footvalve don't keep air in the tank fill water at its full it will help to suck

My opinion, and ill try it my self. Make the out let of the water longer than the intake, to avoid the air to be pulled in by the intake. And second make the intake as high as posible in the vacume chaimber to have as little air in as posible,

Ganito po gawin mo dpt ung inlet mo at outlet ay magkapantay para gumana ang pump mo iangat mo ung drum mo para magkasing level ung dalawa makikita mo gagana yan. Masyado kasing mababa ang outlet mo kaya hindi sya humihigop

Tingin ko may kulang sa set up mo bos, try mo lagyan ng foot valve yung tubong sumisipsip ng tubig. May nabibili nyan sa Lazada mura lang. Try mo lang suhesyon ko. PVC foot valve, available sa Lazada.

what is the name of the pump system ?

At least you're trying. It's ok to fail because you learn what does and doesn't work. You can always combine a cars generator/alternator with a water pump out of your water tank and it will run as long as you have water feeding it. It would solve your problem because you don't have to worry about water pressure. You lot have gave me great ideas so good luck guys from Australia

it is just a siphon effect it will not work when the outlet is higher than the intake, bubbles will just go in the outlet to fill the bucket with air.

Sir Juls apply ram pump method I guess mogana n xa.

❤

Sir we need demonstration for big deep 150 meter borewell Thanks

What about if you install a ram on the line of your discharge, please try it.

Sir J&Js san ako makabili ng wiggle wire at U channel po..magkano po kaya amg mga ito?

Kylangan mo ng flat steel drum, at ms mhaba outlet

It will only work if the tank and the pipes are completely airtight, thus causing vacuum action to pump water in and out of the system. However, air will form when water is heated by the sun thus releasing tiny air bubbles along the pipes. Air can also form when the nutrient solution reacts with heat absorbed by the pipes and the tank. Hence the sporadic release of water through the pipes as you've noticed in the video. This is what we call Airlock, and it caused this project to fail.

Pwede yan pero dapat matibay yung body tapos liitan mo yung intake mo ng one size ska lagyan mo ng tubig na pondo yung pipe... may mga gumawa na nyan nasisira nga lang kagad yung body dahil sa vaccuum pressure na tuloy tuloy

Hi Bro, the only way I know to do that one is wind power or water power on the incoming side to move a scoop paddle, dipping into Ur chemical water for irrigating Ur system!! Nice try!!