John Deere Deck Leveling; Fastest and Easiest Method GUARANTEED

No video

John Deere Deck Leveling; Fastest and Easiest Method GUARANTEED

Рет қаралды 64,856

Жыл бұрын

Deck leveling for the John Deere X500 series and X300 series tractors has never been easier. I use the owner's manual to walk you through the fastest and easiest way to level your deck in record time.
🔴🔴🔴Tools and Products used in this video🔴🔴🔴
Digital tire pressure gauge geni.us/hFJAm (Amazon)
Deck leveling gauge geni.us/BZpli (Amazon)
Deck leveling gauge I don’t like geni.us/Hb5Zovr (Amazon)
Ratcheting wrenches geni.us/i3EY6 (Amazon)
🔴🔴🔴👀👀Watch Next👀👀🔴🔴🔴
Check out this Fall leaf clean up video using only the John Deere bagging system:
• Fall leaf cleanup usin...
Lawn tractors and great because of all the different attachments you can get for them. Here's a playlist of my favorites:
• Riding Lawn Mower Atta...
⭐️⭐️⭐️My Top 10 ESSENTIAL Lawn Care Products for Every Home Owner⭐️⭐️⭐️
🔴The Anderson’s Barricade Pre Emergent geni.us/Jg5MNq4 (Amazon)
🔴Ortho Weed B Gone geni.us/hDrcNSS (Amazon)
🔴Jonathan Green Black Beauty Ultra Grass Seed geni.us/Fj38BI (Amazon)
🔴My Soil Test Kit (2 Pack bundle w/ probe) geni.us/BxqhpG (Amazon)
🔴Scott’s Starter Fertilizer w/ Mesotrione geni.us/ty1xOT (Amazon)
🔴Orbit Sprinkler Timer (3 port) geni.us/grfcf0A (Amazon)
🔴Jonathan Green Soil Amendment geni.us/1BZZz7 (Amazon)
🔴Talak Insecticide (Bifenthrin) geni.us/Mm5Efp7 (Amazon)
🔴Simple Lawn Solutions Soil Loosener (Liquid aeration) geni.us/6WODn5s (Amazon)
🔴The Anderson’s Weed and Feed geni.us/IW1MLx (Amazon)
As an Amazon Associate, I earn from qualifying purchases.

Пікірлер: 48

@suburbanacreage Жыл бұрын

I love lawn tractor attachments and accessories, check out some of my favorites: kzfaq.info/sun/PL0E1kMrOt5Df_mnyY5RtZofWNRMcJEpHu

@robbieharris9339 2 күн бұрын

Perfect, I was wondering how to use the factory gauge and you covered each point perfectly !!!

@joshdevine8006 Ай бұрын

Thanks for this video! Super helpful and way better than John Deere’s attempt at showing this

@heatherwasniak9697 2 ай бұрын

This is the most clear video I have seen on this! Thank you!

@suburbanacreage 2 ай бұрын

Glad you found it helpful!

@normmiller-l4o 11 күн бұрын

I have an. X 738 and my neighbor has a X350. I've had john deere for over 30 years the only accurate way to level the deck is a deck leveling gauge. I used the plastic gauge included with the mower and neither one of these mowers were level after using it! Had to bring back into garage and use the lever type gauge. You cannot get a level cut unless you check each blade Happy mowing

@paulfox3532 3 ай бұрын

This doesn't really apply much to my just purchased S100, but I couldn't leave without noting my appreciation for your snark and sarcasm!

@suburbanacreage 3 ай бұрын

Thanks Paul! Trying to bring up the entertainment value to simple DIY videos.

@scottwegner Күн бұрын

This is awesome. Really well done! Thanks!

@larryanderson599 Ай бұрын

Now, I thought that was one real good video. Easy to understand. Thanks for sharing it.

@suburbanacreage Ай бұрын

Thanks for watching Larry!

@rsmith8646 Ай бұрын

Thanks for the help. Installed a new set of blades on my X300 and the left side was cutting much lower than the right, thought it had a bent spindle but it just needed leveled

@dominicmurphy7929 Жыл бұрын

Brilliant and simple - thank you. So much easier than following the manual!

@stevekurtenbach1951 9 ай бұрын

Your video was the best and clearest that I have found. My X500 did not come with a manual. Thanks for all the info

@suburbanacreage 9 ай бұрын

Hey Steve, thanks for watching. Here’s the rest of my deck leveling content if you’re interested in seeing more. Good luck getting that bad boy dialed in! John Deere Deck Leveling TESTED: What Works BEST! kzfaq.info/get/bejne/obqEd8V3sdPWn58.html John Deere deck leveling DIY: how to make the adjustments needed for a perfect cut kzfaq.info/get/bejne/nbJ8gqSgy7DMhoU.html

@tonydrywall4245 2 ай бұрын

Thank you for showing the easy and fast way they help me a lot

@jamesgaul1022 2 ай бұрын

Great explanation. I have a X300 and my leveling gauge is not under the seat. I believe it is as shown in your video. Currently, my mower is not cutting level. I'm looking forward to this adjustment to see if it helps.

@georgemcbride268 Күн бұрын

When you measure the right side, where the bagger is, from ground to the underside of the deck, there is a metal bracket for the bagger along the bottom of the deck so you are actually measuring from the ground to the bracket...not to the deck. There is no bracket on the other side. Therefore, the bagger side (with the bracket under the deck) is going to be higher than the other side. Don't you think that will make your deck just a little unlevel, versus a deck without a bagger system? I don't have a bagger, and don't have that bracket on the right side. Also, I use the small wooden blocks, but I actually made my blocks longer so I can level my deck at the actual height that I mow it at. Like you, I mow with it set at 3", so rather than level it 2.5", and then set it to 3" to mow, I cut my blocks to fit under the deck when it is set at 3". Then I know it is level at the height I'm cutting. Otherwise, great video.

@ibeturface Ай бұрын

My favorite line ever "now most of you wont recognize what this book is" lmaoooo

@suburbanacreage Ай бұрын

The often overlooked but always information packed Owner’s Manual!

@cgnicolis 5 ай бұрын

I like the 2x4 spacers you made.

@jefflampman492 Ай бұрын

Very helpful. Thanks

@cervelott 2 ай бұрын

I like to cut my lawn at 4.5. It's a bit of a pain on my model adjusting my scalloping wheels. Could I not 3 blocks of wood at say 4.25"s (you cut yours at 2.25") and if the front and sides are all touching equally I know she is level. I know JD says to use 2.5" cut level on the deck for leveling as that is most accurate but I figure regardless, if each block is cut to the same height, and the deck is touching equally on the blocks and the scalloping wheels are not touching I should be good to go. (I have the X350 and have seen the video you speak of). Loved your video, thanks.

@boomer2095 11 ай бұрын

The one issue I have is with the front adjustment. Whenever I get it set perfect, I tighten up the back nuts and it raises the deck. I now leave the deck in from a little low to accommodate for tightening the nuts and then it seems to be fine

@kenthompson3730 Жыл бұрын

Thank you. Great instruction. I’m picking up my “new” X500 soon. I believe the adjust is done slightly differently.

@suburbanacreage Жыл бұрын

Mine is an X540, so it has the hydraulic deck and power steering but it should be a very similar process. Check for the level tool in the height adjustment knob and look for the raised ears alongside the back of the deck. Those will be giveaways that it’s the same.

@timkorth 4 ай бұрын

Thank You sir, worked great.

@gkalligher1958 3 ай бұрын

Great information!

@2014cwajts71 6 ай бұрын

You did the best with what you had. I think the deck leveling adjustment design leaves a hell of a lot to be desired. This video helped me out quite a bit though.

@user-fk9oc7fp5f 11 ай бұрын

How do I put my jd xtrax in forward and backward

@donburton5323 7 ай бұрын

Good advice I bought one of those leveling devices also and was not impresse.

@jimdandy7772 Жыл бұрын

Great video, thank you

@suburbanacreage Жыл бұрын

Glad you found value!

@Tigerfan50 3 ай бұрын

Question. You set the deck height at 2.5", but you cut the 2x4 blocks at 2.25". Why?

@suburbanacreage 3 ай бұрын

The blades, technically speaking, sit up inside the deck a little bit. So if you’re measuring off the bottom of the deck for leveling purposes, the blades will be sitting a little bit higher. I cut the blocks shorter to accommodate the difference that is the bottom of the deck compared to where the blades actually cut. It’s a “quick and dirty” way of deck leveling and the purists will trash the method saying height should always be measured at the blade, not the deck housing. This method gets me close enough for the DIY stuff I do though. Hope that helps 👍

@TheGreatConstantini Жыл бұрын

My X350 does not have the same leveling points. There is a small nub on the left side which I used but nothing on the other side. A well all the instructions say to make the adjustment on the front, measuring on the one side left side rod but you really have to do both sides and I could never get the whole thing even. So on my two front rods I am using a small level. Lastly it is not perfect after adjusting everything repeatedly I cut the lawn and looked at it visually. One side was still lower than the other so I manually adjusted it until it cut right.

@suburbanacreage Жыл бұрын

The X350 is a little different but it’s very similar. The level gauge is located under the seat and you’ll also need the adjustment tool that goes through the holes to turn the bolt from the top, an improved design compared to my tractor. Here’s a video for more specifics on your exact tractor: kzfaq.info/get/bejne/m9mPrZmbrLGWo2g.html

@JoeBaldwin-jx8iy Ай бұрын

I bought my x350 5 years ago, went with the 48" deck option. This mower has never cut good from the start. New blades, sharpened blades, different style of blades. Leveled the deck per manual and 10 or 15 you tube videos. Talked to the john deere dealer I bought it from and he suggested maybe a bent deck, bad spindle, belt slipping issue. I thought I had the right solution, My garage floor has a drain in it, so it is not level. Built myself a level platform, checked to make sure it was level with a 6' level. Releveled the deck. Now the outside blades cut good, but the middle blade is cutting like there is no blade there at all. Oh and the bottom of the deck is powerwashed every couple of months in case anybody is wondering. Is there something I am missing here? Other than I could have saved myself a lot of grief and frustration and about $3,000.00 if I would have went to my local hardware store and bought a cheap murray. Which is what my Dad has and it cuts flawlessey. Anybody out there having the same issue with john a deere 48"deck?

@nathanbrunner6026 8 ай бұрын

do you still have your john deere x540 tractor?

@suburbanacreage 8 ай бұрын

Heck yeah bro! It’s in my will to be buried with it.

@DH-mf2lv Жыл бұрын

Your way may be faster and easier but if you want accuracy, use the John Deere measuring tool that you threw away.

@suburbanacreage Жыл бұрын

It’s not really “my way”, I just followed along with the owner’s manual. I might do a video comparing the two methods that John Deere outlines and first level the deck based on the three leveling points and then go around with the gauge and check the blade height to see if it’s different like you suggest it might be. When you say “accuracy” are you referring to level or height of cut?

@DH-mf2lv Жыл бұрын

@@suburbanacreage That is a great idea to compare! I look forward to it. What I am referring to is verify the blades are 1/8 inch lower in the front and the same on each side.

@ralphhowell5885 2 ай бұрын

I enjoy sarcastic humor. Say, why were ya wearin' ear muffs while airin' up yor tires?

@suburbanacreage 2 ай бұрын

Because prior to that, or maybe during, my compressor is running and it’s loud as hell. I mute most of my clips because the noise of the tools gets in the way of the narration and it’s hard to hear. Plus nobody wants to hear the audio of my air compressor screaming away. I also listen to music/podcasts so rather than constantly take them on and off, I just keep em on.

@TheBusdriver72 2 ай бұрын

@@suburbanacreage Yeah, that's kinda what I thought. I was pretty sure you weren't the type to wear SWAT ballistic body armor when ya go out to trim the hedges.😁

@suburbanacreage 2 ай бұрын

I always try to wear the basics because people always comment if I don’t.