John Deere load shaft seals

Рет қаралды 26,503

Күн бұрын

couple pointers that I do or look for when doing seals
funny how 25 years ago load shaft seals was a big job, pulling pins could tie up a long time. now it's an hour and your done!

Пікірлер: 29

@kiwifruit2022 Жыл бұрын

New shaft and seals and not replace the bushes that’s a bit doggy John. Greetings from Australia love your vids

@scottn2113 Жыл бұрын

My tractor is famous! I didn't know I owned a movie star! I'll watch the mailbox for the royalty checks.*********Thanks for working on "Charlie"!

@AnglesideFarm Жыл бұрын

I remember doing this on our 4020, it sure didn't go as easily as your install did, this will help others in the future who will be looking for a "how to" video. Nice job Jon.

@jonstevensmaplegrovefarms3754 Жыл бұрын

Yeah you're 25 years ago when I was young and learning it was a half a day project. Fight them arms off seem like the bushings wouldn't come out.

@TAHDAHFarm Жыл бұрын

Thanks for the tip on the seals. I have always struggled getting them inside like that. 🤦‍♂️ hot water. I have used the freezer to get things cold to help.

@ButlerFam Жыл бұрын

I did this job over a year ago on a 4040. Was amazed JD only asked just over $100 for the new shaft. Thought it would be more.

@shaneholst6940 Жыл бұрын

Thanks for the tips!👍

@95Thagen Жыл бұрын

Great video

@stuartsplace100 Жыл бұрын

Hi,i am Ed from Vermont,i found your link on Trinity Dairy,awesome family farm

@jonstevensmaplegrovefarms3754 Жыл бұрын

Thanks for stopping by. Trinity is a wonderful family!

@carterblann2290 Жыл бұрын

Might have to put some shims in that 50 series now

@dannychall 11 ай бұрын

You didn’t show putting the seals in . That was the whole reason I clicked on .

@jonstevensmaplegrovefarms3754 11 ай бұрын

Putting the oring and Teflon in? There's not much to show, but I can do it again next load shaft we do. Put Teflon in hot water, and it gets back to shape easier. Push one side of the circle in to make it smaller diameter, put it in and take your fing and get it back to shape.

@karlsborgwi.jewell9919 Жыл бұрын

I tried to save some money by cleaning a little bit of rust off the shaft with emery cloth.. it cleaned up nicely, I put new seals in with the Old Shaft. …a week later i hadta do it all over to put a New shaft in because it wouldnt seal on the old shaft….i didnt save Any Money and wasted alot of time that i didnt have to spare….😂😂😂

@jonstevensmaplegrovefarms3754 Жыл бұрын

Ha yeah, atleast you tried!

@chrisbertrand3989 Жыл бұрын

That allis chalmers hiding in the corner

@jonstevensmaplegrovefarms3754 Жыл бұрын

Yep, 45 for some restoration work.

@pinesedgefarm1155 Жыл бұрын

So if a person has to replace the bushings, how do get them out? I've found the seals are the easy part to replace.

@jonstevensmaplegrovefarms3754 Жыл бұрын

I use the old load shaft to hit the bushings and a 10 lb mall. Usually come right out. Like a bearing race if they are stubborn a weld bead inside the bushing and allow to cool will shrink them and they should pop out. New ones I use a 10lb mall to drive them in, on 30 inch spacing tractors I would use a porta power, make darn sure you go in square, an hour in the freezer ahead of time wouldn't hurt

@pinesedgefarm1155 Жыл бұрын

@@jonstevensmaplegrovefarms3754 thanks!

@marksonnek1305 Жыл бұрын

You can buy a tool that folds up the seals for installation. Pretty inexpensive on Amazon.

@jonstevensmaplegrovefarms3754 Жыл бұрын

Really?!

@smalltimefarmer2701 5 ай бұрын

My parts list has the option for oversized bushings it says use with case marked 0520 where to find this

@jonstevensmaplegrovefarms3754 5 ай бұрын

Somewhere on the trans case. I know not much help, haven't looked for a case number in a long time. What tractor are you working on? Try to measure bushings before taking out. You might be able to just put new orings/seals in.

@smalltimefarmer2701 5 ай бұрын

10-4

@smalltimefarmer2701 5 ай бұрын

4230 power shift wanna go with everything new while I’m doing it

@jonstevensmaplegrovefarms3754 5 ай бұрын

@@smalltimefarmer2701 I still wouldn't put in new bushings unless old ones are out of spec.