Makita GA4530R Angle Grinder | Unboxing and Setting Up

No video

Makita GA4530R Angle Grinder | Unboxing and Setting Up

Рет қаралды 77,955

3 жыл бұрын

Amazon: amzn.to/3sQJS5M
In this video I show the unboxing and the setting up the Makita angle grinder GA4530R including installing of the grinding wheel.
115mm or 4 inch wheel diameter with maximum wheel thickness of 7.2mm. Rated speed of 11,000 rpm with no load. Weight 1.8kg. The tools is intended for grinding, sanding and cutting of metal and stone materials without the use of water.
#makita #tools #anglegrinder
Note: Always wear appropriate eye and hearing protection. Always read the instruction manual before setting up and using the equipment. Have fire extinguishing equipment ready to hand.

Пікірлер: 86

@JohnCarverUK Жыл бұрын

Makita GA4530R Angle Grinder --> amzn.to/3Mdb2ko

@VintageRVAdventures Жыл бұрын

Great angle grinder.

@DiggingwithDallas 3 жыл бұрын

Did an abrasive wheel course at my very first job the course was 1/2 day. On the way back the works van decided to break down on this. 1/2 course ended up go on forever brake down to a garage hat to wait for the boss to bring 2 cars to get us all back. Managed to get over time as well!! Win win

@JohnCarverUK 3 жыл бұрын

Lol ... can't refuse the overtime :-)

@richardharrold8777 2 жыл бұрын

Thank you, John. This was very helpful. I also read your replies to some of the other comments here which were also very helpful. Great use of KZfaq for a functional, well put together tutorial in what I anticipate will be one of the more well used tools in my shop.

@JohnCarverUK 2 жыл бұрын

Thank you very much for the feedback. Glad it was helpful!

@davewr82 4 ай бұрын

totally agree with Richard - brilliant

@mirtaxiomelyssandin2001 Жыл бұрын

Thank you very much! Very helpful and easy to follow up. God bless you🙏🏾👏🏾👏🏾👏🏾👏🏾👏🏾👏🏾👏🏾👏🏾☺️👌🏾👍🏽

@JohnCarverUK 11 ай бұрын

Glad it was helpful, and you enjoyed the video!

@zimbaliretreats 2 жыл бұрын

Thank you- video was perfect👍 ❤️ from Jamaica🇯🇲

@JohnCarverUK 2 жыл бұрын

Glad it was helpful!

@HappyCamperTales 3 жыл бұрын

Makita is a great brand to buy.

@JohnCarverUK 3 жыл бұрын

😀🚙

@abdurahman1259 10 ай бұрын

Very good information given,

@JohnCarverUK 8 ай бұрын

Thanks for watching and welcome the feedback.

@MrRobertojg 2 жыл бұрын

Hi, Good short video and introduction to the product. Just one, but I think important point to make. In the video you say that the supplied disc is a 'Cutting' disc for metal. As far as I am aware the actual disc shown is a 'Grinding' disc for metal. This is an import distinction as using a Grinding disc for cutting and using a cutting disc for grinding is potentially very dangerous. In the interests of safety I just thought I would raise the issue.

@JohnCarverUK 2 жыл бұрын

I will have to take a look back at the video and see what I said, against the product supplied.

@simonhendy199 2 жыл бұрын

It's definitely a grinding disc with that thickness!

@robinbomai9319 Жыл бұрын

Nice set up John 👍

@JohnCarverUK Жыл бұрын

Thanks Robin 👍

@asfuss 4 ай бұрын

Very helpful!!!

@JohnCarverUK 4 ай бұрын

Thank you Alex

@danielbarrett8560 10 ай бұрын

Very useful thanks!

@JohnCarverUK 8 ай бұрын

Glad it was helpful!

@robertr2731 Жыл бұрын

Thank you for you're help

@JohnCarverUK Жыл бұрын

Happy to help

@patscanlan2678 6 ай бұрын

When using with a wire wheel cup brush do you remove the flange?? TY!

@JohnCarverUK 4 ай бұрын

I am not sure to be honest.

@Samboy666 14 күн бұрын

Thanks this helped me a lot as I couldn’t get the guard on lol But isn’t that disc a polishing disk not a metal cutting disc. It’s way too thick

@JohnCarverUK 8 күн бұрын

Thanks for the feedback, glad that it was of use to you with the handle issue.

@danielbonner8309 2 жыл бұрын

The makita 4 inch is my favorite of all time and I have had about 10 different grinders. The smaller body feels great in your hand and they are tough and reliable. Replace the brushes and switch and theyll keep going.

@JohnCarverUK 2 жыл бұрын

Totally agree!

@Retrobots Жыл бұрын

Great video!

@JohnCarverUK Жыл бұрын

Thank you very much

@poohpot4462 3 жыл бұрын

Thanks so much for this. Very useful 👍

@JohnCarverUK 3 жыл бұрын

Thank you very much for the feedback.

@kathykeane9022 2 жыл бұрын

Hello John. I want to use a steel cutting disc (which was sold with the unit) but it won't secure - not as thick or shaped as the grinding disc. The instruction manual is useless. Thanks in advance. Catherine

@JohnCarverUK 2 жыл бұрын

Thank you for the feedback Catherine.

@mariacolon2954 2 жыл бұрын

Excelent video!

@JohnCarverUK 2 жыл бұрын

Thank you very much 😀

@bikemancambs 2 жыл бұрын

first time useing this today , the switch isnt good and the handle is very cheap , sound is ok and cutting is fine

@JohnCarverUK 2 жыл бұрын

Thanks for your feedback regarding the equipment.

@AT_PokemonTCG89 2 жыл бұрын

Just bought one need to cut subway tile for by backsplash. Does anyone know if this tool can cut tiles if I buy the right blade or can I use the diamond blade if it comes with??

@JohnCarverUK 2 жыл бұрын

We have never cut tiles with ours, so we cannot give you the answer. Others might be able to.

@eddyhmmk1 Жыл бұрын

Kinda sucks how the guard doesn’t have a quick adjust. But this thing is a beast, compared to my cordless.

@MrCleitus Жыл бұрын

The guard set up lame for sure when compared to Bosch, it's only 720 watts also.

@JohnCarverUK Жыл бұрын

Thanks for the feedback both.

@cliffcarlo180 Жыл бұрын

Only design fault is the on-off switch. Dust can accumulate behind it after a while making the unit difficult sometimes to switch and stay on.

@JohnCarverUK Жыл бұрын

Yes, I would agree with that experience.

@5295665 Жыл бұрын

Thanks bro

@JohnCarverUK 11 ай бұрын

Welcome glad you enjoyed.

@harrytimko2206 2 жыл бұрын

Good video.. can I use a Ridgid multi grinding diamond wheel with a Makita grinder? I ask because there is no room on the driveshaft for the inner flange nor the locking nut with the Ridgid grinding wheel.

@JohnCarverUK 2 жыл бұрын

Thank you for the feedback. Sadly, I dont know the answer to your question.

@bmzaron713 2 жыл бұрын

thank you

@JohnCarverUK 2 жыл бұрын

You're welcome

@TheSr73 2 жыл бұрын

Thanks for the video. I'm looking for a 9565crv or this one. The former has sjs I and this sjs II. Does it make any difference?

@JohnCarverUK 2 жыл бұрын

We are not sure, sorry.

@josivasam8932 Жыл бұрын

Do you know where to purchase the 4 inch cup wheel?

@JohnCarverUK Жыл бұрын

Is this the sort of thing you mean? amzn.to/3sHIlko

@Wooshandpush1 4 ай бұрын

Does it come with a disk

@JohnCarverUK 4 ай бұрын

Yes it does. Check the product link.

@naspiasaronay3532 2 жыл бұрын

Can I use this machine for wood? I hope you can make a video for this.

@JohnCarverUK 2 жыл бұрын

Yes, if you use the right type of disc. You can also use other attachments such as a rotary wire brush, as we do.

@melvinsanchez245 3 жыл бұрын

Cuantas revoluciones por minuto

@JohnCarverUK 3 жыл бұрын

It has a no load speed of 11,000 rpm.

@billyatkin 3 ай бұрын

Place the inner flange over the shaft 😂😂😂

@JohnCarverUK 3 ай бұрын

Lol... it would be rude not to

@andrewrichards3520 3 жыл бұрын

nice video, not to long, does not rabbit on.

@JohnCarverUK 3 жыл бұрын

Thanks Andrew 👍

@Clairezee5 3 жыл бұрын

No way can we remove the locking nut it’s rock solid

@JohnCarverUK 3 жыл бұрын

Just checking, are you attempting to turn the nut anti-clockwise? You may need to tap the spanner sharply with a hammer or similar. You can clamp the used disc in a vice, but don't reuse it afterwards.

@barrypickles6546 11 ай бұрын

That's a bit crap for makita, handle that you have to use a bolt in, no cutting guard.

@JohnCarverUK 11 ай бұрын

You think so? It works a treat I feel, glad I bought it, have used it loads.

@barrypickles6546 11 ай бұрын

@@JohnCarverUK yep, if you need to take it off it's a pain and if you cut anything you risk sparks

@timwilcox960 3 жыл бұрын

Not a bad effort John but your vid' does have one major flaw. When inserting the cutting disc you say: "make sure you get it on the right way" - or words to that effect. However, you don't explain what the 'right way' is! If I was installing the disc supplied by Makita, I'd just follow what you do, but that won't work as I'm fitting a diamond blade instead (bought seperately). So, explaning which way is 'the right way' to instal discs/blades is, IMO, a major component of a setting up vid' of this kind.

@JohnCarverUK 3 жыл бұрын

Hi Tim, thank you for the feedback which is welcomed useful constructive criticism, and which will be taken on board.

@timwilcox960 3 жыл бұрын

@@JohnCarverUK Hi John, glad you've taken my comment in the spirit in which it was intended! In all other respects, it was a well put together and well executed short vid'. (Short is good btw, very good.) You could do a follow up vid' in which you address the different types of discs/blades availaible (along with their respective uses), with particular focus on which way round each one needs to be fitted. If you do, be sure to address which way around the locking nut goes on as well, as I copied you in this vid' which, needless to say, is the wrong way around for a diamond blade! ;-)

@alistairseaton800 Жыл бұрын

@@timwilcox960 This is precisely the info I'm looking for. I've bought a different blade and im not sure which way the nuts should go....

@funkidstv5308 3 жыл бұрын

Your not saying which side to put handle on if right or left handed. I'm a complete novis. I'm only having to guess here 🤦‍♀️

@JohnCarverUK 3 жыл бұрын

Thank you for your feedback.

@funkidstv5308 3 жыл бұрын

Can you please let me know? ;)

@oranobrien872 3 жыл бұрын

@@funkidstv5308 if you’re right handed, you use your right hand to hold the body of the tool and the handle goes on the left. Vice versa for left handed