Hi Everyone here is a small clip of how you should the clutch fork retaining spring and release bearing should look like when they are installed. If you have any questions please feel free to contact us sales@actionclutch.com
Пікірлер: 22
@riverios5334 Жыл бұрын
How does it sound like when it makes contact? I got my clutch system replaced and there's a constant ticking noise coming from the clutch. When I push the clutch pedal in it goes away but comes back after I release. It sounds like the ticking from the wheel of fortune. I took it back and they say it's rust on the fork that's rubbing.
@slip.r7026 Жыл бұрын
Mine has the same problem
@ghost-carnage89645 ай бұрын
I can't tell you what kind but some clutches just rattle/tick. But it could also be your throwout bearing or pilot bushing I believe.
@actionclutch3 ай бұрын
If you are hearing any ticking or metallic grinding noise but goes away once you press the clutch pedal in the bearing is making contact with the pressure plate at all times most of the times the issue is that the clutch pedal was not adjusted or properly adjusted after the clutch kit was installed so I would double check that asap as this can prematurely wear a clutch kit unit out. -Cub
@jadey4231 Жыл бұрын
I need help On mine !! I did a clutch change and I’m still not creating pressure , it has so much play
@actionclutch Жыл бұрын
Hey Jade can you email me at General@actionclutch.com and I will help you out. Thanks!
@dustinchad11 ай бұрын
get a mighty vac or one like it. and bleed it. otherwise get on board with taking her out again to verify this step here.
@dustinchad11 ай бұрын
it did not !look like that when stabbed her back in, i stabbed it back and now it's not contacting so thanks for the video ! something to know for the new comer. 😱😂 but hey we havet a new transmission jack this round so lets go!
@actionclutch2 ай бұрын
With proper transmission jack you should be able to get it mounted no problem.
@ramonclemons8196 Жыл бұрын
I have issues in this area.. low clutch pressure. Not engaging/ disengaged
@jadey4231 Жыл бұрын
Did you figure it out ?
@actionclutch Жыл бұрын
Hey Ramon email me at general@actionclutch.com if you haven't already solved your issue. Thanks!
@robsenb16 Жыл бұрын
When you install the spring the wrong way around, would you still be able to shift and drive? I replaced my clutch and have low engagement, low pressure and half of the time problems getting the gears in. I bleeded it 50 times, no air comes out anymore. No leaks.
@codiecoons541011 ай бұрын
Did you replace the throw out bearing too?
@robsenb1611 ай бұрын
@@codiecoons5410 Yes I did. But I found the problem. Somehow I messed up the spring that sits on the clutch release fork. It was not sitting in the right postion. So I had to take off the transmisson again. Was a pain in the ass but I also learned something lol
@actionclutch2 ай бұрын
It would give you engagement issues I would inspect everything all over to make sure everything is good.
@robsenb162 ай бұрын
@@actionclutch Thanks for the reply but I found the issue. I put the release fork bracket in the wrong way. Another pain in the ass lesson learned lol
@TheShangralaaaa17 Жыл бұрын
you didn't lubricate the clutch fork or the pivot ball
@wiggitywhitefox Жыл бұрын
Weird what’s that red greasy shit on the pivot ball?
@actionclutch2 ай бұрын
They were properly lubricated...
@matthewkrengel61433 ай бұрын
grease???????
@actionclutch3 ай бұрын
Yes light grease on the pivot ball and where the fork makes contact with the release bearing tangs 😎