Karcher SC5 Steam Cleaner - Lets take a look inside a steam cleaner. Does your money worth it. Please watch till end. #KARCHER #STEAMCLEANER #SC5 #TEARDOWN
Пікірлер: 45
@magnormicavlogs38214 жыл бұрын
Wow lods, ngayon ko pa to nakita. It's educational po. Keep it up!💪💪
@antonbacs134 жыл бұрын
Thanks
@waldemarkwiatek39634 жыл бұрын
22/5000 A great video Thank you
@sunrisesunrise53483 жыл бұрын
I have sc4 red light is flashing despite there is full water in the container i have tested solenoid valve ok, the pump imk is ok but it doesn't run when connected coul you please help. With thanks.
@danielar-l24172 жыл бұрын
Hi, I had the same problem. Red light flashing on the SC5. Tested the solenoid and the pump and all were in good working order. I disconnected the water tubes attaching to the pump, shook out excess water within those which looked like it might be creating an air block, filled up the water container and added water directly to the pressure chamber. Reassembled everything and it started working again. I'm not very technical and can't be sure that clearing those tubes of water actually solved the issue but I couldn't find any other videos or posts resolving this particular issue so thought I'd post a response to the excellent video shown here.
@rynie63342 жыл бұрын
Thanks for the video! Mine has a problem: it heats up and releases a good blast of steam, but then the steam soon slows to a trickle. If i depress the trigger, the pressure builds up again, then the same: blast to trickle. I already bought and replaced the solenoid but it made no differnce. Any idea what the problem/fix could be?
@davidcouper46363 жыл бұрын
Great video 👍🏻 I have the SC5 and when I dock the removal reserve tank the pump starts to try and pump but then cuts out - do you know what this could possibly be? Could it be limescale blockage in pipes?
@champagne_charlie10 Жыл бұрын
Hi. Please can you offer some advice. When I plug my sc5 in and switch it on the house electricity trips. I've had a look inside and can't see any wires a miss or faulty looking. I'm afraid that I don't have a multimeter (actually I did until someone stole all of my tools!). One thing I do notice is on the base of the boiler there is a little bit of corrosion likely coming through from the inside. Any ideas much appreciated.
@antonbacs13 Жыл бұрын
Hello, please check the heating element at the bottom of the boiler.. I believe these heaters are grounded already.. Also check the solenoid coil, it also causes the breakers to tripped off..
@champagne_charlie10 Жыл бұрын
@@antonbacs13 wow thanks so much for replying so fast. I'm more of a carpenter mechanic guy but electrics are still alien to me. Pls tell me we you say check these things, what do you mean? I can buy a multimeter sure no problem but what am I looking to check. My dad was a spark so he can chip in to. Thanks a million 👍
@ljp19427 ай бұрын
Would you recommend this product after pulling it apart ?
@antonbacs137 ай бұрын
Will not last long if you use it everyday.. 30mins to an hour of usage would be fine..
@antonbacs137 ай бұрын
Will not last long if you over use it.. 30mins to an hour of usage would be fine..
@assa3956 Жыл бұрын
My sc5 can’t fill the boiler, if i fill boiler directly everything great, but when the boiler is out of water cant fill from tank! Do you have any suggestions?
@antonbacs13 Жыл бұрын
Try to descale the boiler first.. there is a problem with the water level sensor inside the boiler..
@assa3956 Жыл бұрын
@@antonbacs13 thakns for reply, i did it but nothing changed, when boiler out of water the red light stays on (not flashing), and steamer not working at all
@asem4232 жыл бұрын
I have DE4002, It is said that the pressure pump is faulty due to limescale. Is it possible to fix this?
@antonbacs132 жыл бұрын
Yes, you can buy a descaling powder to remove limescale inside the boiler..
@asem4232 жыл бұрын
@@antonbacs13 thanks a lot
@jack_s2k_8903 жыл бұрын
Thanks for your video. I have the model sc 6.800 c. When I plug the plug into the socket, the power in the house goes out. I tested with the tester the continuity of the heating resistances. And they seem to be working. What do you think it could be?
@antonbacs133 жыл бұрын
I think your heating element is already grounded..
@antonbacs133 жыл бұрын
Try to check the heating element with your tester, one probe to the heating element terminal and the other probe to the boiler body.. If there is resistance then your heating element is grounded..
@jack_s2k_8903 жыл бұрын
@@antonbacs13 I disassembled the tank and found many limescale deposits. And in the lower part a corrosion of the aluminum that went beyond the whole base, up to touch the resistance.
@champagne_charlie10 Жыл бұрын
@@jack_s2k_890 Só do think the corrosion was causing the issue? I gave a similar problem with my sc5 model. I don't have anything to check resistance but I can not see any problems when I take the machine apart. I can just see a small bit of corrosion coming through the bottom of the tank.
@alikhan-ri5ye4 жыл бұрын
Thanks My SC5,is making steam,but it is not coming out.Descaling with karcher didnt work. Due to lockdown,i am unable to take it to shop. Any idea why the steam is not coming out?Thanks
@antonbacs134 жыл бұрын
If the steam is not coming, common problem is the solenoid valve failure.. the solenoid valve responsible for opening and closing the valve when you press the switch at the steam gun..
@alikhan-ri5ye4 жыл бұрын
@@antonbacs13 Thanks,is it something i can fix myself?how?
@antonbacs134 жыл бұрын
Its difficult to change this solenoid coil if you are first timer.. better to a technician.
@Margeriteful3 жыл бұрын
Is the Tank Made of Aluminium or stainless Steel?
@antonbacs133 жыл бұрын
Its made of Alloy..
@raymondmok6803 жыл бұрын
May I ask what if the maintenance valve is stuck. Any ideas how to open it? I've tried the pipe but just won't open it.
@antonbacs133 жыл бұрын
If the cover of the maintenance valve is already loose, remove it and use a monkey plier to remove the maintenance valve.. that valve needs to be replace..
@raymondmok6803 жыл бұрын
@@antonbacs13 Thanks! It is actually too tight and not able to open at all. The plastic cover is well attached with whatever under it... should I break the plastic and reveal the metallic parts under?
@antonbacs133 жыл бұрын
Yes, remove the plastic cover. You will be able to see the actual maintenance valve and use the monkey plier to turn the valve.. its the lime scale that made the valve too tight..
@antonbacs133 жыл бұрын
If the plastic cover is still well attached to the valve, then try to turn it harder..
@raymondmok6803 жыл бұрын
@@antonbacs13 Sure will try again with the plastic tube, hopefully it wont break the tube. Thanks again for your input.
@konny4353 Жыл бұрын
What size ist the key ?
@antonbacs13 Жыл бұрын
Its either 5 or 6mm..
@konny4353 Жыл бұрын
@@antonbacs13 thank you so much👍
@konny4353 Жыл бұрын
Hallo , what key do i need to unscrew the bottom ?
@antonbacs13 Жыл бұрын
Hello, you need a star allen wrench key to unscrew the botton..