Keep Your Mustang Hood Where It Belongs With A Set of Quik-Latch Hood Pins!!

Рет қаралды 10,802

Жыл бұрын

🛠️ Download our free guide: The tools you need to work on your Mustang!
bit.ly/465MGQT
Purchase these Quik-Latch hood pins:
www.cjponyparts.com/quik-latc...
If you are running a lightweight hood, you should use a set of hood pins to keep it in place. A loose hood is a danger to your vehicle and other vehicles on the road. These Quik-Latch hood pins look clean when installed and keep your hood where it belongs, even at high speeds. Follow along as Bill shows you how to install these pins, and even shows you what NOT to do as he makes a mistake on the installation!
#s197 #mustang #hoodpins #hood #carbonfiber
Subscribe for more info and installs!
kzfaq.info_c...
Learn more about your Ford!
www.cjponyparts.com/resource-...
Music provided by:
elements.envato.com/curated

Пікірлер: 21

@sn95_mustang_garage Жыл бұрын

I just got rid of my brand new 4” Cervini hood and went back to stock. I also had these pins but never did install them of course. Thought I was but I am just not a cowl hood pin guy I guess. This is pretty hardcore.

@steveb8883 Жыл бұрын

I have these on my 2022 Mustang GT. They are great. No hood flap at high speeds and the hood is secure. Buy them.

@lesterli3043 22 күн бұрын

4:27 I have to point out, there are many people doing this in the wrong way, that is why you had a wrong pin location in your video later and had to relocate it. DON'T drill all the way up through the top of the hood if your hood has two layers, you should ONLY drill through the bottom layer and then hole saw a big enough hole to allow the washer to slide in, then repeat the tape and center punch method to PRECISELY determine the center location of the hole on the top of the hood, that is when you can drill through the top, via the big hole you opened up on the bottom layer.

@driver28bear Жыл бұрын

Sweet Car!! That hood looks really good on it too. Great installation video...Thanks!

@thecamarogarage 6 ай бұрын

I seen another video with a different way if drill They marked where to drill and bolt on rods. Then put felt mark on end. Lowered hood onto rods to mark the underside of the hood. Drilled i pilot hole on the lower part (structure) of the 1st layer of the hood. Used a hole saw to cut out diameter from bottom layer. Debur edges. Then marked felt on rods again, carefully lowered hood which now put the mark under the actual hood itself. Drilled a pilot hole on that hood itself, hole saw the underside of the hood itself now, debur, and screw in the hood latch... and was perfect.

@jerryjimenez7108 3 ай бұрын

Yeah I could’ve sworn saw this??? Could you link it or title it

@nickkostakis9600 Жыл бұрын

Great job mate you make it look so easy thank you very much

@stewart-D Жыл бұрын

These quick latches are an excellent product

@RepoDraghon Жыл бұрын

I used a set of these of the smallest version I could get on my rear bumper and trust me when I say follow the recommendations of installing the pin first then finding out where it hits on the hood or panel as I have misaligned a couple...

@cjponyparts Жыл бұрын

As have I lol

@79chevy901 Жыл бұрын

I like those hood pins.

@BroncosandPartsGarage Жыл бұрын

That passenger pin. Ouch

@honk3x 2 ай бұрын

Anyone know how to remove the hood open warning ?

@ecbrixs403 6 ай бұрын

How exactly did you go wrong with the drilling?

@Ricky_Rocha 4 ай бұрын

I want to know also. Like what went wrong because he said to drill at an angle and he did but still made mistake? I’m just curious

@driftitlikeyouownit 3 ай бұрын

He drilled at too much of an angel changing the trajection of the hood pin and latch. The reason you mark the hole and drill a pilot hole is because you actually are drilling straight on the hood just at an angle because the hood is sitting at an angle. He should have made his template and marks for the catch on the top and bottom of the hood.

@Ricky_Rocha 3 ай бұрын

@@driftitlikeyouownit thank for the explanation I was confused

@wildpony1957 Жыл бұрын

I just kinda cringed watching the drilling!

@LoverJ Жыл бұрын

I don’t understand why he would use a 7/16 drill bit, if he was going to use a pilot bit that would be a lot smaller 😂😂

@cjponyparts Жыл бұрын

Not my finest moment lol. I followed their instruction and sadly couldn’t undrill the hole. I make mistakes too and wanted oriole to see that.

@CraigPatersonII 4 ай бұрын

Yeah when he went through both layers without doing another pilot with the pin angle I just started nodding my head. If the instructions are like that that's terrible.