I had a problem like that with my e Revo when I linked all my traxxas rc cars to one remote I had to put the Bluetooth link in and set the steering up on the app and now it’s working as normal.... Top video Kev keep up the hard bashing

Tighten up your servo saver or put in a stiffer spring

Depending on your new esc your Bec output could be set super low that would make your servos very weak

Hello from New York, This channel kicks all kinds of ass. Keep up the good work.

It's a old soul, from the wired cars that only turned one way while backing up lol

The jump out the car trunk was cool. I like jumpin my rcs out my truck bed, kinda the same😎🤙cool vid as always dude

Love my e revo, put 400 into aluminum upgrades and went with stiffer springs and shock oil. Amazing truck, love watching you bash it.

I've had the same problem with my Rustler 4x4. As soon as I put a faster and stronger 3rd party servo in there, the steering was pretty much gone. BUT only when TSM was enabled. As soon as I turned it off on the transmitter, the steering was perfectly fine again.

Hi Friends, i know lot of you buy in banggood so i have a question ,im from Spain and i bought a car on frebuary the 13 and banggodd said send the car on februay 22, now is march 23, and car dont arrive.this is posible to be so slow or i have to be worried?i insert my track number in the UPS page but it tell me tracknumber not found (i choose CN storage not USA storage).Please help,thanks

Thats a bummer that steering on the e-revo is always jacked up!

Same thing happened with my e-revo and I think it was to do with battery voltage or overcharging but I played with it for a few hours unplugging and plugging stuff back in and it suddenly started working so I checked the batteries and the voltages were lower than when it stopped working

Hi kev Have you checked the screws that hold the front ball screws in place? The ball screws that hold the hub carrier to the front upper and lower arms are held in place by black screws that use the grey tool that came with it. If there too tight then it stops the ball joints rotating and restricts the steering. Failing that etronix 20kilo servos

I would go with John Smith check you esc settings and if that checks out look at your steering servo if its plastic look for cracks or wear marks... The only other thing l can think of is to check is the mechanical side... The steering mechanism, see if anything is bent, loose, or to tight I enjoyed the video and hope to see many more!!!

So the steering just dies for a couple of seconds? I have that issue, x-maxx with 2085x servo

We’res the lambo bash😂

I feel your pain all the way over in the US Kev! My E-Revo 2.0 is a blast to drive, when it works. Mine acts like that when a servo dies and that's every single run, at least one new 2075 will die. I've since replaced them with some Amazon high torque all metal gears and so far they seem to hold up, just a little slow from side to side.

I love all your rc vids,and that lambo is dope 🤘

Love your videos keep it up hope you get to a million subscribers.

I had this problem for a bit too, there's a dead zone in the "traction control" knob on the remote, try putting it all the way up and see if that helps, also if the steering servos aren't aligned properly it may cause this

Hey Kev great vid so far love ur craziness you got me into tv cars I bought a traxxes rustler last week.thanks for getting me into tv cars.

Kev, I had the same problem with the steering and forward throttle. I'm a novice, but it was the tqi assistance on the remote caused no steer. You made need to use another remote. Edit: It's caused by the knob closest to the trigger.

Try the heavy duty servo saver spring. Not sure if the V2 comes with that stock or not. I've put that on all my revos, nitro and electric. Helps get the power to the wheels. Part 5344X. I just looked at the parts explosion for the ERBEv2 and it does come with the softer spring.

So this has happened to me before. Both my nitro 3.3 and erevo 2.0. Try taking the steering assembly apart and you may find that the post that holds the steering assembly together has come out of its hole. This binds the steering and makes it so the servo saver is doing its job, but that also means that the saver gives rather than turn the wheels. I hope this helps!!

I put the 400oz Traxxas servo in our erevo. Also I love the wheelie bar on the erevo makes it more controllable .

My e revo does the same thing sometimes when my tsm is shut off completely. Try turning it up and see if that helps.

Greetings from Texas have a great day Tips for getting a servo right and even on a 2wd Traxxas slash?

I had this issue with my steering!! The plastic nuts that hold in the pivot balls was way to tight. Just barely snug it up and make sure you put dust cover back is it doesn’t back out. Hope this does the trick

same thing happens to my OG nitro revo found out its when i use the remote for other trucks since it has two steering servos. i just press the set button and redo the controller. plus it reverses my throttle a lot as well

“Oh it’s MY sand pit!”

Kevin Mad respect man 🙏🏻 I wanna do the same

Rc cars always have some sort of problem. But they are so much fun anyway. Great video as always Kev!

Guys I updated the firmware on my esc today and now have nothing, no steering or throttle control. Any advice would be helpfull

I just got a 8s x maxx and I would love to set it up just like yours. Do you have/ can you make a list of all the things you've done to your x maxx? Thanks in advance!

I absolutely love your videos Kevin! Keep up the great work! Ps do more videos on the traxxas udr

Your servos are working against one another maybe? Awesome video kev!

M8 I have a Losi Ei8ht that is currently set up for nitro, and a fully loaded HPI Blitz and a brushless setup. These vids make me wanna take the piss and go full bonkers!!!! Cheers m8

I had this issue on my 1s gen erevo brushless it was the pillow ball cup nuts the piece that screws into the hub to cover the pillow ball is too tight along with the pillow balls themselves hope this helps

hi, which servos do you have in it, maybe try the organs, I also had the problem and it was because the servos are not original, if they are not original, maybe they pull too much current so you do not properly function, you would then have to solder 1 pack to the Esc of 5 to 10 volts. for pulling to the LEFT / RIGHT there may be dirt in the tires, good luck!

Kev, the TRX receiver only puts out 4.2 volts, which is not enough for a high voltage servo. Especially 2 high voltage servos. You can try a glitch buster with one high voltage servo. That made my Revo 2.0 a little bit better. I am pretty certain that the 2 servo channels split that voltage as well, meaning each servo is only getting 2.1 volts. I have not actually hooked a meter up to the receiver to verify that however. You could always put in a BEC or get a different receiver as well. A new ESC and receiver are in the near future for my 2.0 and will probably be a BLX or Hobby Wing ESC and a Tactic receiver. - Cheerio Mate!

Just buy a new one lmao Nice Vid as always Love ya vids Imma order a 1/10 or 1/8 hsp buggy today brushless that can run 4s

Another best RC video with my favourite KZfaqr ever good lad 👍

Oh!!!! I just bought a x Maxx s8 2 hours ago and yes bought all upgrades you run. SWEET!!!

My slash has a problem where the green light goes on and it drives like normal but after 5 seconds it stops and the red light goes on like it is out of charge this keeps happening even when I try different batteries and un plug it and plug it back in again

What mic do you use? I thought somebody was driving an rc car around me

Awesome video again Kev. Discovered your channel recently, inspired me to buy my first decent RC car! Cant wait for it to arrive! Keep it up!

I WANT A "TUMBLE WUMBLE" SHIRT..LOL

Kevin has the best sick videos ever crazy c maxx jumps insane

You just need to use one servo a man. Maybe a savox sa 1256 tg servo man. It has 20kg torque at 6 volt. And I have seen them for 70 euro's at conrad electronics. I got it in my erevo for almost a year now and still doing great. Love your content man

Hey kevin, i just stumbled over your channel this morning, and I have been glued too the screen ever since. I would love to get into R/C Cars on the hobby level. But I was wandering what car i should get? (im 22 years old) I was thinking of buying the "Traxxas Slash 2wd" (the basic model not the VXL) But with my very limited experience in the field, I would love to get a more professional opinion on the matter. Hope you can help me. 🙂 I would also appreciate any ideas and suggestions from other people with R/C experience. Any and all help would be appreciated. 🙂

Kev the best mod for the revo steering is to get rid of the dual servos and go to 1 single super strong at least that's what we do for the customers in my shop.

Hey kev, biggest thing that i have found with e-revo servo (or any ball type suspension for that matter) is if you over tighten the caps that hold the steering knuckle to the a-arms. At least thats helped on mine.

Summer nights getting stoned up the golfy, I need an rc as an excuse to reminisce!

I'm sad, I'm back to school and now I can't be up at 2:00am watching you epic live streams

For the e revo have you tried looking at the servo saver that s what happened to mine

big fan I have an e revo too keep up the good vids!

Kev I had the same problem with my erevo all you have to do is recalibrate the esc sometimes it’s take one or two times and then it will work or you can send it to traxxas and they can fix it but most of the time you have to do it when you turn it on and then after like a week of me doing it it was fine and run just fine now

Hey, have you checked your steering servo saver? It could be loose.

Which is better, erevo 2.0 with slash 4x4 or just an xmaxx. I have many upgrades on my erevo and slash but I want an xmaxx. Should I sell my two cars for an xmaxx?

From my own personal experience, if you tighten the pivot ball caps too much it can bind the pivot ball. If this is the issue loosen the caps a 1/4 of a turn. I upgraded to aluminum Hot Racing axle carriers so that the caps would be made out of metal instead of plastic.

Im thinking of getting into rc planes, does anyone know a good step in plane? I saw a few flite test planes like the tiny trainer and explorer and they seem good starters bc of 3/4channel and cathedral

You should make shore the servos sent fighting bye endpoints

I had same problems open up the receiver box and I cleaned my bored with a clean dry toothbrush and no more problems

The servo arm might not be long enough or something to do with the font axle

Check the rod links in the middle snap bi-valve in the servo. Could be gummed up and not allowing the pivot coils to engage which would make the servo useless.

Dicen buen video y el video dura 11 min ,pero de kev todos los vid son buenos ;)

Great crew! Best team out in this show!

UK has very nice place for RCing! Love it.

Install an external bec for your servos. It looks like brown out is what you are experiencing. You can then send a specified higher voltage to the servo than what your esc is outputting. I do it with all my rigs.

Kev check the plastic pieces that go on the pivot balls. If you make those to tight it will not steer. I had that problem with mine. That weird looking gray tool is what you need. Just back those out.

might be a dumb question but did you try adjusting the steering trim?

My xmaxx did the same thing, the esc wasn’t delivering proper voltage or something. I swapped for the max6, no problems since. Never looked back.

Is the BEC setting in the speedo set to 6v?

the servo saver could be slipping, just a thought. my tmaxx is doing the same thing, I thought it was the servo so I threw a new servo in it but the receiver is too old XD

I’ve been having a lot of trouble recently sort of like you but with my kraton and a savox servo.

Have you tried adjusting your trim on the remote

Hey Kev I have an e revo and I really don’t want you to give up on yours just keep solving problems and you will soon have an absolute fun machine trust me it’s an awesome truck

Maybe its a Traxxas stability manegment (TSM)....

Your videos are awesome man. Is it possible to you, to test and modify the HBX Survivor or Reely Core Brushed Series? The HBX Survivor and Reely Core series are the same. Reely were sold in Germany by Conrad Elektronik.

Alright Kev, theres a few things that could be going on with the steering. Prime culprit is the TSM being turned to just off the Full off position. I learned about that the hard way by running into my ankle on 6s at a fairly high speed. Next up, if youve set your suspension links to the hole with the most ride height, youll have to adjust your toe in angle and it wouldnt hurt to check the camber angle as well. Next up, remove the the steering linkage and tires to make sure the axle carriers can move freely but without slop. I run Power HD 20kg servos in my 2.0 and have the bec on my Max8 esc set to 7.4v. Works good with that setup. If youve got the bluetooth module for your remote or one of your friends does, link up and check to see if your steering sensitivity is set to 0 and didnt accidentally get changed by trying to adjust something else. If all else fails, SEND IT TO THE MOON!!!

First 200 I love your videos you inspire me so much keep up the good work you should do a video on a traxxas slash 2wd

Hey kev! Do the zop batteries fit in the e revo 2.0???

Lubricate the little pins for your steering

You probably need an external BEC. The built-in BEC of the ESC is probably struggling to power both Servos. A lot of ESCs will have their BECs overloaded by even a single Servo if its powerful and draws a lot of amperage or you set the BEC Voltage too high.

Haha the flat earth thing had me going lol..

I’ve had this same thing on my traxxas slash and it’s been pissing me off, if I somehow find a solution I’ll let you know

The bolts that are attached to the knuckles are sometimes too tight, I have an e revo 2.0 too and I just fasten them a little less

Incredible video... Many of your shots were off the chart. And who does the song? Would like to hear more.

The erevo needs the upgrade servo saver spring which is alot tighter so it transfers alot more torque to the wheels . I also fit a jx 46kg

Hey kev, man thats odd even my stock steering seems ok hope you figure it out these new revos are insane!! Haha

Your my favorite KZfaqr because you listen to your comments and most other KZfaqrs don’t to me that deserves a subscribe

Alignment can make a world of difference on the revo , mine has a little toe in on the front and a little negative camber, rears as square as possible. And it goes like the clappers! And didnt you have the same problem on anoter car? That turned out to be the transmitter

Try tightening the steering sensitivity by turning the little disk to the right by the steering part of the axle.

steering clutch is either broken or not been put together perfectly Kev. I had this prob with mine, a clip that holds the spring in place, only a mm or so but it was enough to effect the spring force. hope this helps bud

Have you checked the parts in your steering assembly?

I had the same exact thing going on with my erevo 2.0. I changed out my receiver and worked perfect after that

You need a glitch buster.. servo or something sucking too much juice probably.. mine was doing that and a 5$ glitch buster/capacitor plugged in the receiver was like magic lol

This video was better lay out it's better like this well done keV😄

Kev you are the man love all your videos looking forward to the next one are you going to take out your nitros soon been waiting to see them run got one on my nitros running and will put a video on my KZfaq soon

Another great video,keep it up.

Try loosening up your front pivot ball caps top and bottom, but not to much or your wheels wobble. I've had the same problem before. If they are fully tighten you lose steering.