BEST "How to" video I've ever seen! Didn't spend the first 15 mins talking about himself, and telling us to "be sure you're wearing safety glasses..... STRAIGHT to the point, with no B.S. VERY WELL DONE👍
@hacktheropy1758 Жыл бұрын
He never got to the point😂🤦🏼♂️
@colecarpenter712 Жыл бұрын
He never gave a solution or even verbalized his issue
@Kevin_aka_RockGuy9 жыл бұрын
For those of you who have this problem the solution is simple. If you flip the shaft and the gear over and look at the end of the shaft that goes into the case, look at the end of the the two...there is timing marks punched on the gear and shaft that have to line up on the shaft for the spring tension to be correct. It is that simple.
@cliveswabs9365 Жыл бұрын
So simple i dont understand
@chrisvillarreal2752 Жыл бұрын
No it is not I have the parts installed correctly and the spring still pops off every time the case goes the spring is worn where it insert into the hole and the hole itself is showing signs of wear. Replacing the spring solved the issue.
@charliewebb5895 Жыл бұрын
Yours still a hero 7 years later! Just rebuilding a car 125 2001 and run into the problem! Legend
@shaynet28568 жыл бұрын
the spring is located in the hole closest to the gear. not the hole on the shaft. this will allow the spring to sit closer to the gear and to be pretensioned. he has put the spring in the shaft hole not the hole closest to the gear.
@jeffersonblake89123 жыл бұрын
You just got me back up and running i didn’t see the hole further back and put it back together wrong and broke my case. It’s fixed now!!
@kemperloggins35572 ай бұрын
yo i love you. i just spent 2 days fighting the case and you just pointed out the exact priblem. your a absolute legend
@brysutube9 жыл бұрын
You need more preasure on the spring. Move the spring back more, or the post that it gos on. You should have to really pull on the spring to get it in place so it will hold
@jensenmiller64104 жыл бұрын
Sweet, just broke my spring this afternoon so now I know I don't have to take the clutch off.
@jensenmiller64104 жыл бұрын
RIP, the mounting point for the spring in mine is a piece of metal secured by a allen screw. The screw immediately stripped out and I do not feel like doing a full tear-down to get that fucker loose. I'll survive, it only takes a couple of kicks to start anyway.
@drakecrawford12885 жыл бұрын
What the hell am I watching
@zoologicalmilitia22412 жыл бұрын
I wanted to take the pull starter off a 79 cc predator and replace it with a kick-starter what problems do you foresee and what solutions? Obvious I'm not going to have that spring toe-hold.
@JizRagg11 жыл бұрын
what hole is it? im about to put a new spring in and i dont wanna mess it up.
@McrnightlifeАй бұрын
The honda cr85 kick shaft is really tricky to get on, the hole is located bottom left and when spring pops off there is no way to get the spring arm past the clutch basket whilst its still in place so you have to pull kick shaft off completely (making sure the locations marks are lined up ) put the pin in the hole then use the actual kick on the shaft and turn it putting tension on the spring until it goes past the little catch that sits behind the shaft then push it all into place while making sure the other spring at the back sits in its place and the main spring doesn’t spring out of the hole, takes a good couple of tries ill tell you that 😂
@TAPASBLITZ4 жыл бұрын
Hi can kick start spring come out of place during kicking it bc I don’t know if I have to replace it or just refit it in
@timothygifford27475 жыл бұрын
Why does my FA50 Suzuki kick starter housing have ( ?? ) oil in it ? Is it necessary.
@brantleysmith549410 жыл бұрын
Is this pretty much the same on all bikes.
@snapplecreampie8 жыл бұрын
i think u gotta use the kick start lever to actually turn the kick start spindal to get the spring into place~
@jasonfreet77414 жыл бұрын
This is exactly how you must do it.
@Goldenfightinglink3 жыл бұрын
Nice, I was looking for the answer before actually trying it. Thank you very much!
@danhillman45234 жыл бұрын
Line up the marks on the gear and shaft. I did the same thing. Once.
@cliveswabs9365 Жыл бұрын
How
@bigboi65787 жыл бұрын
when you say mum i got this but you dont no what you are doing ahha
@Kevin_aka_RockGuy9 жыл бұрын
To clarify further...the gear is a two piece ratchet and the inner ratchet piece is what has the stamp mark on it. Line this up with the stamp on the end of the shaft and your good to go. Hope this helps you out.
@G_G_G_G_6 жыл бұрын
Kevin Keller I wish I understood anything you said :(
@reecebrambrinnk7383 Жыл бұрын
super helpful, thankyou
@Vespalupita11 ай бұрын
Não entendi
@kevinalbers10845 ай бұрын
I do not see any timing marks on mine. What is the stamp mark look like? DT125 Yamaha
@muzashah60755 жыл бұрын
Achanak meary Honda 70 ka kick free ho gaya. Kia masla hai?
@billsviews456510 ай бұрын
Hey mate this is a long time ago video but do you know where I can buy the same spring you have
@waynewigger99043 ай бұрын
Putting the case on keeps it all together
@yoyodelatorre98345 жыл бұрын
De que moto es ese motor
@pallepuha34136 жыл бұрын
thx
@DxP176raju5 жыл бұрын
Mera discover 150 cc ka motorcycle hm kicksell fracture hogiya bina engine khule kesa change karna hm plz help
@nickkrug81576 жыл бұрын
The spring shaft that goes in the hole is TOO SHORT.. some how
@MrSniperdragon4510 жыл бұрын
does the other half of the casing hold it in?
@dedmemesarchive5554 жыл бұрын
nope, he put the spring in the wrong spot, its supposed to be in the back.
@shubhammirzapuricomedy11606 жыл бұрын
Honda 110 ka kick spring kaise dala jata hai please video bnao
@crf1008 жыл бұрын
I had the same problem on my cr80 take the shaft out check that the two punch marks are next to each other and if that dosent work use rtv to hold the spring in the case so you can get the side on
@drummerwithatrike7 жыл бұрын
You my friend are a legend. Your comment helped so much. Thanks for that. If your keen ver in Australia the beers are on me.
@micah-hooka72752 жыл бұрын
Dude, I’m completely rebuilding an 89 Cr 80 and trying to restore it to new condition. Parts are all but gone out there but I have 3 toasted crankshafts in 3 lower ends which still. Have plenty of good parts. I can’t get that spring to seat. Is it supposed to go in that inner hole on the center casing? I have new seals and gaskets and that’s the only thing that’s stopping me from completing this bike. I managed to get all the plastics back to nearly new condition with powder coated frame . Found a seat cover for that specific 1989 year. It’s the all red CR 80. I’m just hung up on this darn kick start spring assembly. This was a comment from six years ago. I hope you will hear me out there in the KZfaq world.
@eddiesibrian6356 жыл бұрын
how did you remove the kickstarter
@johnnygalvan1344 Жыл бұрын
Omfg you saved my life ! I couldn’t figure out what the hell was wrong with my bike until I seen this
@cliveswabs9365 Жыл бұрын
Did u manage to get the kickstart locked on to the shaft that turns the engine over
@johnnygalvan1344 Жыл бұрын
@@cliveswabs9365 yes
@johnnygalvan1344 Жыл бұрын
@@cliveswabs9365 wasn’t easy tho
@cliveswabs9365 Жыл бұрын
@@johnnygalvan1344 i made the mistake of using silicone gasket which is 0mm thick ...when 1mm thick is needed to release the spring
@cliveswabs9365 Жыл бұрын
Tolerances are so tight
@abhishekbk33025 жыл бұрын
Bro pls give solution I have pulsur bike twin disk but kikar is not there so pls me solution how to fix kikar
@xaupuia9675 жыл бұрын
I need rx 135 kick clip where can i buy?
@kjsbigboy45011 жыл бұрын
The gear does not look like it is in all the way and I think u got the wrong hole look for an other free hole on the back side that is where mine is but I don't know what bike u got or anything hope this helps
@dannilaser16 Жыл бұрын
Well, what kind of bike is it?
@kirkconway10 жыл бұрын
I hads the same thing on this 86 KX 500. have new lever have to get input shaft. then fix it. then normal again.
@t.r.d.machanik74735 жыл бұрын
Oh good
@marclalonde73957 жыл бұрын
My Foster son bought a 93Yamaha RT180. The kick start spring was broke. Got a new spring but cant seem to see where the free end of the spring connects. Cant find a video or Pic to show where it connects . Any help PLEASE would be appreciated!! I'm assuming under the clutch maybe?
@bestcomedyvideos84606 жыл бұрын
Marc Lalonde जाने आलम
@garrisonb3746 Жыл бұрын
When the kickstart shaft is in the correct positiong. The correct hole for the spring is towards the bottom left.
@adibayu87185 жыл бұрын
Bos gimanh masang gir koping lepas motor fu syh nii carah ya bos
@edwardgolonka-jd4sc Жыл бұрын
Vise grips?
@chevy55157 жыл бұрын
Kawasaki wrong hole
@Mukeshsaini-pw5ov5 жыл бұрын
Bajaj cT 100 new model kick sparking dalana
@maryjanechavenia76624 жыл бұрын
paano po ayusin ang sa sym 100 tumigas po yung padykan nya parang may ntanggal po sa loob
@joeyconrad20243 жыл бұрын
the crankcase has to be on
@Avidity100010 жыл бұрын
your inner washer notch must slide over the inside spring tang you dont have this properly installed. The outer spring tang DOES go in that hole if you have a honda crf 04-06 do not attempt to bend the spring until you have the base properly installed.
@brtmizar1443 жыл бұрын
Motor apa tu mas
@kamimao91043 жыл бұрын
Tysm
@jesusolvera15403 жыл бұрын
I have a 450r trx, it doesn't turn that way, you know why this happens to me
@gdavies1987 жыл бұрын
side case I made spacer
@silkcustoms5202 жыл бұрын
Did you fix it yet
@apolloxkwd9009 Жыл бұрын
Can i ask whats the name of that spacer that you have put inside the spring?
@gustavoavina3136 Жыл бұрын
Spring Collar
@elvinelvin24222 жыл бұрын
Could I get the name of the spring ???!!!
@pappuchandelpc7146 жыл бұрын
125 cc me pikup aur avrage ka sandar sangam ka nam bajaj xcd125
@ysharaajoc58944 жыл бұрын
sir ung fury namin minsan pag nag kick slideng minsan hindi tapos pag nag andar pag off parang may kumahol na aso
@HeltonLogging8 жыл бұрын
bet that case had to be split again , you have to wind the spring once
@stevejones81477 жыл бұрын
Thomas Helton in
@135christian16 жыл бұрын
Ha lol
@lloydlockwood94596 жыл бұрын
fancy finding you here
@ISPNetCenter10 жыл бұрын
This isn't the spring the sr250 needs, check the diagram for the 3Y6 models.
@elgiefaustodayday90264 жыл бұрын
Saan po ba banda kayo sir may pagawa ako
@DRONESnMORE13 жыл бұрын
the coil is a lil too small
@pappuchandelpc7146 жыл бұрын
mera xcd125 2007 model 77 kmpl 180000 km r.
@asghanchi18926 жыл бұрын
kik jam ho Gaye he uske liye video banavo
@xnpoop8116 жыл бұрын
Pakistani macanic is best for all type alteration and tips and tricks of bikes and car
@bike-pin36784 жыл бұрын
De que se trataba ese vídeo mudo...
@avdtv13013 жыл бұрын
mukhang di naibalik ah
@KAMLESHKUMAR-nr6bi4 жыл бұрын
किक का वीडियो पूरा बताएं
@ronnievengado1812 жыл бұрын
Tanung lng Ako idol Ano Kya problema.ng motor ko ok nmn kick nya problema pag kinambyo Muna bgla ppitik Yung Kickstarter nya
@vrsteffen43593 жыл бұрын
Da fehlt noch eine Scheibe. Das ganze wird durch den Deckel gehalten.
@Sams_garage2845 жыл бұрын
My kickstart is not comming back up after its down. Someone plz help
@jasop12915 жыл бұрын
Mechanic kid 17 bro same
@jasop12915 жыл бұрын
Do you have a yamaha
@Sams_garage2845 жыл бұрын
@@jasop1291 yes I do Yamaha blaster 200
@edwardgolonka-jd4sc Жыл бұрын
Sleeve extension
@greaselover32486 жыл бұрын
In order to take out that whole shaft do u have to remove the cluch basket
@jessewilson18446 жыл бұрын
GREASElover32 no
@olevik2311 жыл бұрын
kind of dirt bike ???? yz85 ????
@Sonu-fb8go5 жыл бұрын
Sonu
@AIRMANBEAR11 жыл бұрын
PUT A SHARPER BEND IN THE SPRING AND/OR GRIND THE END OF THE SPRING TO LEAVE A SHARP EDGE THAT WILL CATCH ON THE ALUMINIUM DO IT WONT FALL OUT
@gdavies1987 жыл бұрын
Merthyr Tydfil boy
@rubercuaichar55856 жыл бұрын
Nececito un crank de patada para xt 225 yamaha
@84BigRob11 жыл бұрын
yo u are silly
@Ace010103 жыл бұрын
Thats the wrong hole lol. That's definitely what she said.
@amirbinomar3 жыл бұрын
1billion view
@donwagster5 жыл бұрын
Use duct tape and a clothes hanger. Remember a girl has 2 holes .
@bricehale65935 жыл бұрын
Lol
@blikedon30665 жыл бұрын
All the girls I know have 3 holes
@kaiyan2993 жыл бұрын
Made 9 years ago 2K subscribers with nearly a million view 😂
@user-wg5rt9jl6y6 жыл бұрын
अनिकेत् वर्मा
@tirthanathdey89276 жыл бұрын
Lmm ardeno FX full engen fates
@remexremex16586 жыл бұрын
i
@Offensiveword3 жыл бұрын
Don’t speak whatever you do
@randhirbaba27977 жыл бұрын
my rx100 kik spring problem how to solve please tell me ya me your mobile no.