Very informative, made a jig like yours to do our truck and worked like a champ, thank you.

Amazing how easy the new pin went in. Considering the bushing material; odd the old on was sized up like it was. Dusty dry though.

We welded a jig that bolts to the spindle and has a pipe that's centered over the kingpin and we drive it out with a sledgehammer. Works great for this job.

Best video I've seen on KZfaq in a long time. King Pins are never fun. You make it look easy!

Ты красавчик, береги себя. Хорошей и денежной работы тебе. Не стесняйся своего английского и смело комментируй что ты делаешь.

Excellent video.... Shame I only found it AFTER I had done one. Thank you

It's amazing how smart some people are on here . You'll spend a couple hundred dollars on pins and bushings and not twenty dollars for grease and a bottle jack .

This guy does take a lot of risks.and that kingpin did not know grease on its lifetime😋

You are a Master Mechanic. Great job.

Awesome, I couldn't imagine how you were going to break 2 20-ton bottle jacks. I was imagining jacking up the truck; but how do you break a 20-ton jack doing that? And I was impressed with that jig you made to remove the king pin. Also, whoever edited this has mad skills!

thank you for great detail video on show the job

great video, thank you very much, I will take my truck to the mechanic, there is not way I can do that!!

Great video, now I understand why the repair shops charge what they charge.

Many people ignore!!! That why grease nipples are given to lubricate such moving parts like: king pins, tie rod ends, leaf springs, propeller shaft center bush & shaft cross. It's better to greasing all given grease nipples after every 5000Km.

Very good job ! Very good video !!! Thanks!

GREAT VIDEO THANKS

Nice work! A+

Nice man I wish you be in the area so can give you the job you are doing a great job!

Great work buddy 👍👍👍very good 👍

Thank you 😍😍😍😍😍😍😍😍😍

Wow great job

баярлалаа хөгшөөн/thank you

Wow... Awesome task.

Very informative and much appreciated!! PITA though.. not looking forward to it.

Nice job

thank you

Good job. 👍

Thank you👍👍👍❤🧡🧡

!!!👍👍👍👏👏👏GOOD JOB

Don’t use a wrench on a square head. You will strip it. Use either an actual square socket or a 12-point socket. On a second thought, you can use a wrench, but the other way around where it has a 12-point. The problem, though, will be lack of leverage. I’d definitely go with a socket and a breaker bar. They do sell ratchet breaker bars for a quicker job. I’ve seen some people use an impact wrench on that tool, but I don’t know if the manual says it’s okay or not. Some also say you should lubricate the threads to make the tool last longer.

Use channel instead of angle iron, weld the horizontal top and bottom pieces inside the vertical pieces so they will be stronger. We had a kingpin pressed out of a 1978 Ford F250 pickup. We had to remove the I-beam out of the truck and take it to a shop where they pressed it out. How much pressure? 27 tons.

@ 14:40 Thou shalt not heat up the cast iron I-beam or steering knuckle! You also fail to measure your axle (I-beam) bore for out of round ! If it's out of round, then you need to bore it out and sleeve it back to size or your king pins will have short life.

Awesome!

I have a 50 ton jack ima have to make one now lol

Bravo.

King pins are a king size pain in the ass.

Did you preload the thrust bearing to check if you needed a top shim ?

Nice work! You just outlasted it.

naic jop thanks

Good work. Thanks

great video ! i have a question though. is the work the same for different wheel, w/o brake disc, but a drum?

а регулировочные шайбы между серьгой балки и цапфы,и уплотнительные манжеты с внутренних серёг цапфы,чтобы во втулки грязь не попадала,что не надо ставить?

Do the king pin always have to be pushed upwards to remove ? Or can they be taken out either way ?

No torch on kingpins ever!

I want to ask a question because the piece has play if it is very difficult to remove it

I am hoping someone can tell me the torque specs on the 12 T55 torx bolts that fasten the rotor to the hub. Thanks in advance.

I think better if he spray DW40 first before jack

Bien pero la “percha” es muy frágil tendría q ser dos ejes gruesos con rosca en ambas puntas las planchas de por lo menos 25 mm de espesor lo demás está bien 👍

Is it a necessity to remove the disk and hub out or its possible to work around it?

Well done , can you do mine now ?

Haz pasado más trabajo bregando con la soldadura y el pasador que sacar el king pin

👍

Thank you 🇮🇳⭐⭐⭐⭐⭐👍

How cute r u😂

Well that saved you $2500

If someone follows this guys instructions he could get them hurt this is the kind of you tuber you don't need been there done that buy the right tools this guys a mechanic come on

something is wrong with the playback on this specific vid. buffering out like craxy. other stuff play ok

I forget grease the lower part. Now the wheel shake which king pin loose.

Tiger tool says we can help get that out for about 1700.00..... He be like where's my scrap pile and welder.😆

Can anyone give an opinion of how many hours labour to replace 2 kingpins like on the video?

What size nut on the hub?

How long does it take?

Men playing with tools ,Never say easy

Hello, Can anyone help me with the king pin overall intervention mechanical design. I am currently doing my mechanical engineering course as a final year. Any concrete kind of information would really be appreciated !!💯 New design, new ideas(hydraulic, pneumatic or any transmission system), king pin inclination angle.

Must be Russians that’s how we do it as long as gets job done ☑️

I am heavy vehicle mechanic let job

wow, what a pain in the ass

Muy lento

Hello how much Pounds to move the rotor?

Hello sir good evening how are you fine sir I need you job mechanical

Poor guy please some body tell him how do that before him kill him self

New York mechanics would never do what you did. They simply replace the whole thing not fix it

Scheiss Werbung.

There was so much hack in this I think I caught the covid

Muy lento