I love my CL800. Excellent quality and features. Klein knocked the ball out of the park!

80 bucks is very in accurate...more like 140

Good video friend thanks for show us this video I think Klein clamp meter is a good choice not too expensive compared with fluke or other brands and make the work

Thanks a lot I really enjoy the video I'm interested in getting a Klein clamp meter the same model that you have how can I purchase one .

Good review, does the NCVT also have an audible alert tone along with the light ?

DC current in miliamp range is hard to measure 20 30 mA

Buenas noches este multimetro esta excelente, cual es la diferencia entre el cl800 y el cl900??

The co duct or needs to be in the middle of the clamp. It’s got a 1% +- in the middle and a 2%+- on the outside as per the manual.

ur sposed to line ur wire perpendicular to the two arrows on each clamp arm

I want to know if this will measure up to 1000v DC?

Thanks for this review but you are comparing the Klein clamp meter accuracy against an Innova multimeter which, frankly, is not known to be all that accurate. Not sure which is the most accurate.

Thanks

My CL800 reads 2 to 3 amps on DC setting when there is nothing in it or a disconnected wire. Seems to read all right when current flows. Any explanation for the "phantom" reading?

Can this be used as a non contact voltage tester.? Similar to voltage pen... where it beeps near live voltage?

You have to align the clamp so the wire passes through it in alignment with the (+) on the entry and (-) on the exit.

I just got a CL700 today and am very disappointed because the reading is so huge for the AC amp draw at 35.5-37 when the knob was turned to amp setting when checking the draw for a space heater with 1,500 watts. I knew the amp draw should be around 12 amp but this reading is either way off or something isn't right. I'll return my Klein Tools CL700 back to Home Depot. I've learned that you don't need a multimeter with 600 amp capability because you'll never use a device drawing that much amp and such capability that high will compromise other functions, such as in my case.

Made it to 1:59...You wouldnt use the clamp to measure miliamps, you would use the leads and interrupt the circuit.

Those caps are ur safety CAT IV keep em for when you dick around on big stuff. I have the CL450 and I haven't figured a way to measure DC amps on A~ yet or using the clamp but that's ok i bought it for dickering around with AC single/3 phase motors. The K-type input connecter purchase fucking sucks so bad! I don't know if it's the leads or the machine but it's unacceptable. Line splitter is a must

This guy doesn’t know what he’s talking about

cat IV lead covers

A bit late for this comment but, the Klein is a True RMS meter and the Innova isn't. The meters shouldn't share the same readings.

😁

Dude, thank you. But you should reshoot the video cause you keep putting it in Continuity mode.

Sorry but really poor video. 1) You said the clamp meter is "off"...how do you know the $20 Innova meter isn't "off". 2) You stated you can't use the wire leads to measure amperage as if that's a drawback. That's whole point of a clamp meter. NO small multimeter can measure amperage beyond about 10 amps because it will melt the wires. These tools are designed to measure current running through 00 or 4-0 wire not USB level currents.

Yeah, what they said. Learned nothing

Terrible review.

Gat a Fluke its shit looks like garbage from Sears

this is why dislikes should have never been removed thanks JOE BIDEN

2 min shorter video than the ugghhh ugghhh ugghhh guy.... must be fewer ugghhhhss in this video

Waste of time!

You don’t know which meter is off because you have to Test, each one individually not at the same time. Also, take your clamp meter and test it and non-clamp mode.