KOI POND DIY 3 BARREL FILTER TEST RUN

Рет қаралды 18,573

2 жыл бұрын

KOI POND DIY 3 BARREL FILTER TEST RUN
#koipondfilter #koi #Japanesekoi #diyfilter
I hope you enjoyed the content & consider becoming a Subscriber
Pond Information
3,600 litres ( 792 gallons).
100 liters trickle filter with Alfagrog.
Filterbox Premium 10,000 Filter
Pump = Hozelock Aquaforce 3500 Solid Handling Pump.
UV Clarifier =11w
pondtec pondoAir set 900 = 9001/h 12 w.
2nd Pump was running through the Bakki shower @ 2000lph.
soon to be replaced
Music provided by spoti.fi/NCS artists. Valence, Infinite.

Пікірлер: 84

@GazsKoiPond 2 жыл бұрын

If anyone has any questions about this DIY filter build please feel free to leave a comment in the comments section, and thanks for watching 👌👍😀

@josegandulla6669 9 ай бұрын

Great job!

@aquariumdelirium 8 ай бұрын

I’m loving those dump valves

@PTranProductions Жыл бұрын

Cool!

@GazsKoiPond 10 ай бұрын

thank you

@StokeKoiAdventures Жыл бұрын

Great job, those water butts are great , just bought one for a moving bed. Your System will work great. Amazing flow.

@Crazyforkoiandgoldfish 8 ай бұрын

Awesome job 👏👏

@GazsKoiPond 8 ай бұрын

Thank you

@keepingitkoi 2 жыл бұрын

Looking good Gaz the water level was a bit high though with the hosepipe your pumps gunna be pushing alot more than that got my fingers crossed it works a treat 🤞 looks really smart tho 👍

@GazsKoiPond 2 жыл бұрын

We will see, time will tell Jamie 👍🏻👍🏻

@MichaelHarper-hs4df 2 күн бұрын

Great job, if you don't mind me asking what was the end cost

@GazsKoiPond 2 күн бұрын

Less than £450 all in barrels, pipe work & connections , pump, air pump and stones,

@pondlife6568 2 жыл бұрын

Loving the barrel filter, every time I see it I think that's my next project 👍👍

@GazsKoiPond 2 жыл бұрын

Thanks mate hit me up if you want or need any info but am pretty sure, the videos show all you need to be fair, either way if you need anything 👍👍

@pondlife6568 2 жыл бұрын

@@GazsKoiPond thanks will do 👍👍

@edanderson859 2 жыл бұрын

Looks good 👍

@GazsKoiPond 2 жыл бұрын

Thank you Ed hope your good and family are well 👍👍

@edlesboroughkoipondstevech3546 2 жыл бұрын

Hi Gary, i suspect you need to put a larger volume of water through faster, i.e. from your pump set above the setting you intend to use for a true test. Also there is currently no allowance for the variables such as media, blanket weed and faeces which will slow the flow once into the system, increasing the size of the interconnecting pipework will also make a large difference 🤓🤓

@hertskoi 2 жыл бұрын

Looking good pal coming along nicely

@GazsKoiPond 2 жыл бұрын

Thankyou very much HertsKOI hope your good mate 👍👍

@ashleybooth1062 Жыл бұрын

Have you got a link to the video of how this was made. Including the information on fitting and fixing thanks

@tonybeards2978 2 жыл бұрын

Mate looks a good a good one, I'm interested in doing the same. What size pipe fittings you running..👍

@GazsKoiPond 2 жыл бұрын

At the moment they are 1&1/2 “ in and 2” out that’s 40 mm pipe and 43mm 90degrees 45degrees & 50mm pipe and fittings with 1&1/2 bulkhead in and 2” bulkhead on the flow and returns

@stubbsaquatics6080 2 жыл бұрын

Looks like it will be a good system ... thinking about adding a few barrel prior to my filter falls..

@GazsKoiPond 2 жыл бұрын

Thanks Chris, go for it mate you can not beat a good project 👍👍

@abkoi 2 жыл бұрын

Will work a treat that mate! And cost effective too! 👍🏼

@GazsKoiPond 2 жыл бұрын

I hope so Alex and it will be a heck of a lot cheaper than going out and buying one 👍👍

@davidcart28 8 ай бұрын

Any chance of an update I’m in the process of building a small pond and this looks like a great idea thanks for all the tip and tricks What matting and how have you layered it in the drum

@GazsKoiPond 8 ай бұрын

keep watcing the Videos mate, there are about 8 of all about the build of the system and the filter house

@davidcart28 8 ай бұрын

@@GazsKoiPond I’ve watched them all

@GazsKoiPond 8 ай бұрын

Made them into a play list for you mate

@GazsKoiPond 8 ай бұрын

@@davidcart28 in the 1st barrel is japmatting, 2nd barrel is k1 moving bed, 3rd is static ceramic media, and the returns back to the pond jap mat is stacked on upright bottom row is stacked right to left x5, then 5 again on top front to back

@MrWiskin 2 жыл бұрын

Looks great Gary, but concerned the out flows will become overwhelmed! It was nearly to the top on just a hose pipe flow. Unless your going to run your Vari very low. As previously discussed, let us know yeah?

@GazsKoiPond 2 жыл бұрын

It only just went over half way on all 3 over flows and yes I am running a veriflow pump as well

@TelfordKoiPond 2 жыл бұрын

Evening Gaz👍😊. That looks like a professionally made system👍, very neat, spaced and well thought out👏👍. I’m sure others will be copying your design😊👍. One thing is for sure…..your grass ain’t going to need watering an6 time soon😂🤣😂. Joking apart, nice job mate, looking forward to seeing the next step👍🐟🈲😊

@GazsKoiPond 2 жыл бұрын

Thank you Very Much Phill, its been good fun making it to be fair mate Ive really enjoyed, and yeah your right the grass needed to be cut a couple of days later it had a right growth patch 🤣

@JjustBoy 2 жыл бұрын

It's coming on well that now! It'll be mega once it's all up and running, looks very professional.

@GazsKoiPond 2 жыл бұрын

Thanks Dale I am try to keep it as clean looking as possible I just hope it works as intended 👍👍

@copeyskoichattingbubbles4775 Жыл бұрын

Nice 1 gaz works a treat m8

@GazsKoiPond Жыл бұрын

thank you 👍

@birminghamgary609 2 жыл бұрын

nice work mate

@GazsKoiPond 2 жыл бұрын

Thanks Gaz

@Mikemkp 2 жыл бұрын

Looking good so far gaz 😀👍🏻some release pressure so will definitely push the muck out .

@GazsKoiPond 2 жыл бұрын

Yeah Mike thats what surprised me to be fair, if anyone is walking past the back of my garden when I flush that out, they are going to get a shock 👍👍😂😂😂😂

@bruceodonnell789 10 ай бұрын

Hi, thinking to try this. Just wondered how you got the connectors in at the bottom. Could you reach it?

@GazsKoiPond 10 ай бұрын

Yes I could thats why and how they fitted in there, its a little difficult but dousable...

@peterspuddleskoiandgoldfish 2 жыл бұрын

Looking good mate ,should work well

@GazsKoiPond 2 жыл бұрын

Thanks Peter, time will tell 👍👍

@jonijamessantos6791 Жыл бұрын

If the drums have the same elevation, is there a possibility of backflow?

@GazsKoiPond Жыл бұрын

yeah I had to step them in the end as the flow would not pass fast enough to keep up with the pump

@jonijamessantos6791 Жыл бұрын

@@GazsKoiPond thank youu, how much cm gap did you do?

@GazsKoiPond Жыл бұрын

@@jonijamessantos6791 50mm or 2” mate and it will now flow at 8,000 litres per hour

@djcuro126 2 ай бұрын

What size piping did you use going in and out of the filter.?

@GazsKoiPond 2 ай бұрын

1& 1/2 inch

@djcuro126 2 ай бұрын

@@GazsKoiPond so the same size in and out.? If so I'm happy to hear as I was thinking I would need to do bigger on the return pipes

@GazsKoiPond 2 ай бұрын

sorry 1&1/2 in 2 out, but if you watch all of the videos about the filter you see that I have a plan to change it to 3 inch return watch the full 5 or so videos in the playlist 👍🏻

@timtran4326 2 ай бұрын

WHERE YOU BUY THAT BARREL ? I LIKE

@GazsKoiPond 2 ай бұрын

you can buy them at most hardware stores or on line from Amazon

@topklassphotography 2 жыл бұрын

you need to put the tank connector seals on the outside or water will find its way around the threads and cause a leak unless you have added silicone to the outside

@GazsKoiPond 2 жыл бұрын

No it won't its has ptfe tape around the threads, that product is designed to seal thread's, on plumbing and gas fitting, thats its soul purpose 👍👍👍

@topklassphotography 2 жыл бұрын

@@GazsKoiPond put them on the poutside next time and you want need thread tape just a tip

@GazsKoiPond 2 жыл бұрын

@@topklassphotography thanks, they did not come with any seals for some reason that’s why I got the tape 👍🏻👍🏻 they have held water for 48 hours straight so they will be fine thanks for watching

@topklassphotography 2 жыл бұрын

@@GazsKoiPond i just use silicone now as you say some don't come with seals

@Ryan-mv4jn Жыл бұрын

Don’t suppose u have a way of getting a filter grids to fit in for k1 moving bed 😂I’ve been struggling all day trying cut it out right

@GazsKoiPond Жыл бұрын

try cutting it to the size you want then heating it with a heat gun just enough to bend it to get it in the straighten it out again 👍

@Ryan-mv4jn Жыл бұрын

Done all that still no luck hah they are the same ones you have so u can imagine

@clarencerivers2229 5 ай бұрын

Where did you get the Barrels from?

@GazsKoiPond 5 ай бұрын

B&Q it’s a DIY shop here in the UK just incase your over seas

@KoiCarpKyle2393 2 жыл бұрын

Good barrel system you've made there gaz 👍 I'm going brushes/japmat then moving bed buddy I think not 100% sure myself yet 👍 😁😎🐟

@GazsKoiPond 2 жыл бұрын

That has to be the worst thing mate, making your mind up what to use and go with 😂😂😂👍👍

@KoiCarpKyle2393 2 жыл бұрын

@@GazsKoiPond yes mate deffently gaz is a tricky one it needs to be right init buddy 👍

@GazsKoiPond 2 жыл бұрын

@@KoiCarpKyle2393 it does, you could try one idea and I could try another and we see how it goes

@KoiCarpKyle2393 2 жыл бұрын

@@GazsKoiPond yes mate we'll do just that buddy and see the results they both will work 💯 we just need to know which is going to be more effective insnt it mate 😎👍

@gavinstyles5264 2 жыл бұрын

That looks the dog’s bees my man 👌🏽

@GazsKoiPond 2 жыл бұрын

Thanks Gavin, lets just hope it works right

@lateboomer88 Жыл бұрын

The filter design is very neat and compact. However, the first stage as flow settler is not sufficient to block a lot of fish mock. Therefore, I think you should incorporate Eazypod idea to have k1 media buffer in a separator container and attach to the outlet to block more fish waste and use aerator for backwash.

@GazsKoiPond Жыл бұрын

The filter works fine and has been all season this was just a test stage but thanks for your input, but no easypod will ever be going in or on my filter system!

@skeggy 2 жыл бұрын

Id go static k1 static k1 micro then moving you want as much out of the system before the moving bed split remains self cleaning

@GazsKoiPond 2 жыл бұрын

So static ki first barrel, then k1 micro moving second, hit me up with some prices for the media if you want mate ??, also if you do them things that go in the pipes to stop the media getting out let me know, I need 5 that will fit 2" and 1 to fit 1&1/2" 👍👍👍👍👍👍

@skeggy 2 жыл бұрын

@@GazsKoiPond k1 static .. k1 micro static in 2nd . Then moving bed in 3rd you want the media in the statics about 8 inches to a foot deep and yes I can get the cages