Kubota BX Inner tie rod boot upgrade DIY HOW TO

  Рет қаралды 16,163

NSB Construction

NSB Construction

7 жыл бұрын

This is a common problem on all Kubota BXs as far as I know. I have seen a few videos showing this, but not an in depth how to. If you like it please subscribe, comment, and like.
Thanks
I created this video with the KZfaq Video Editor ( / editor )

Пікірлер: 13
@91rss
@91rss 7 жыл бұрын
just to add, keep the nut on whenever you tap on a tie rod etc, or you will hurt the threads, just back it off a bit, or better, turn it around so you are tapping on the bottom so you dont hurt the castles of the nut ,
@badbobcat5830
@badbobcat5830 Жыл бұрын
If you flip your castle nut over and rethread it on the tie rod until the rod is just starting to show, you can tap out the tie rod without damaging the nut or your threads.
@nsbconstruction9698
@nsbconstruction9698 7 жыл бұрын
I was made aware that you dont need to actually remove the outer tie rod from the knuckle. You can get a wrench on the inner shaft and loosen it that way, you would just count the threads on the inside of the jam nut.
@rosemarygramm5263
@rosemarygramm5263 6 жыл бұрын
Would like to see how you were able to get the boot and washer pushed over far enough to get the e-clip on.
@nsbconstruction9698
@nsbconstruction9698 6 жыл бұрын
rosemary gramm sorry it's been so long I don't remember exactly what I did.
@rosemarygramm5263
@rosemarygramm5263 6 жыл бұрын
I finally had to leave the washer off and just use the e-clip.
@timyoder2003
@timyoder2003 6 жыл бұрын
He doesnt remember lol
@AUoldphart
@AUoldphart 5 жыл бұрын
do your remember the vendor or part number for the boot? Looks like an easier install that with the Kubota boot
@nsbconstruction9698
@nsbconstruction9698 5 жыл бұрын
I dont. Ebay i think. Paul Short on KZfaq might sell one also.
@petejones9788
@petejones9788 7 жыл бұрын
If they had put the tie rod behind the axel they wouldn't have such a problem.
@MrPancake0825
@MrPancake0825 4 жыл бұрын
How are these boots holding up?
@nsbconstruction9698
@nsbconstruction9698 4 жыл бұрын
Mine are doing great
@MrPancake0825
@MrPancake0825 4 жыл бұрын
@@nsbconstruction9698 Thank you for getting back to me. I need the same boots for my L60 and all I am finding is OEM. 🤮
Kubota BX- Replacing worn out front end parts (How-To/DIY)
16:58
Biff's Equipment
Рет қаралды 18 М.
Little girl's dream of a giant teddy bear is about to come true #shorts
00:32
НРАВИТСЯ ЭТОТ ФОРМАТ??
00:37
МЯТНАЯ ФАНТА
Рет қаралды 7 МЛН
Amazing weight loss transformation !! 😱😱
00:24
Tibo InShape
Рет қаралды 60 МЛН
Kubota BX Series Inner Tie Rod Boot Replacement - BX25 / BX22
13:18
If You Own BX watch this Video: Fuel Filter Upgrade
4:56
Tractor Tech
Рет қаралды 69 М.
how to align the tractor front end.
5:13
daveknowshow
Рет қаралды 40 М.
2 Inch Wheel Spacers On A Kubota BX: Full Install, Specs and Test
12:52
Sam's Doin Stuff
Рет қаралды 4,3 М.
Recovering my tipped Kubota BX23s tractor
13:10
Nolan Klein
Рет қаралды 257 М.
Make This Upgrade to Your Tractor Before You Tow Again!  Quick-Easy-Affordable-Safe
8:01
Peek's Peak Hobby Homestead
Рет қаралды 23 М.
Kubota BX Hydro Service (Step by Step)
7:28
Tractor Tech
Рет қаралды 98 М.
FMTV Tie rod boot replacement
5:33
Endless Adventures
Рет қаралды 26 М.
It's Amazing what you can Accomplish with a Box Blade
9:59
Rockhill farm
Рет қаралды 250 М.
Little girl's dream of a giant teddy bear is about to come true #shorts
00:32