L21-30 Power Distro / Amp rack tour

Рет қаралды 33,144

Bruce Bryant

4 жыл бұрын

Following up on our Aluminum cutting video with a finished product.

Пікірлер: 47

@brucebryant6483 2 жыл бұрын

The 90 degree connector caps came from Mouser Electronics MFG P/N 1546349-2

@brucebryant6483 Жыл бұрын

@@TheMyersBrosBand QOU they are. I have a video on this.

@christophermullis6390 3 жыл бұрын

Nice work and very clean layout, unlike some "professional" distro sellers.. love to see this.

@isettech 2 жыл бұрын

The only thing missing is the front panel Volt, Amp, Watt meter for each phase. Good to know if you risk blowing the upstream breaker before you do. I use a 50A spider box for distro and removed one of the GFCI units and fit the space with a pair of watt-meters. Very useful when you have to adapt and feed from 20A or a 30A branch. Killing extra subs is much better than having the show go dark.

@cjramseyer 2 жыл бұрын

Very nice. Incredible attention to detail

@roshanelewis952 4 жыл бұрын

Thank you very much. I have been trying to put a power distribution system and i'm very grateful.

@djjohnnyk4584 3 жыл бұрын

I gotta say well done!! 👏🏾👏🏾👏🏾

@Thisisdjhurricane Жыл бұрын

Great video!

@ThideUpSound Жыл бұрын

Very helpful video. Thank you sir

@juanhodge450 Жыл бұрын

Woooooo Que bien video para nosotros los amantes del sonido

@sheldonbrammer1209 4 жыл бұрын

Hey do you mind sharing the schematics for this setup and where could I order all the parts from please.

@RangerTyrone 11 күн бұрын

I would love to have a custom made just like this one. I am not so inclined to do that build myself. how could i source the parts by the way Sir?

@fitness5 2 жыл бұрын

Found It. Thanks Again.

@brucebryant6483 2 жыл бұрын

Great!

@poserwanabe 3 жыл бұрын

Nice work !!! Obviously you suffer from the same level of OCD as myself...

@renecardenas3237 2 жыл бұрын

Very nice rack. Looking for a small block to wire the white and green. What is that block you used for this build? I need one half that size.

@brucebryant6483 2 жыл бұрын

Looks like this is a 5 position available at McMaster-Carr www.mcmaster.com/9290T12/

@djtlsmooth8640 3 жыл бұрын

This video was great!!!! I’m taking notes. Why not make a custom power adapter and receptacle to convert the 3phase to 3 separate 110v so you won’t have to disconnect power in unforeseen circumstances?

@brucebryant6483 3 жыл бұрын

So in short the 3 phase cable supplying the distro shares a common neutral. If say three 20 amp 1 phase loads ran on this cable that was connected to three phase as intended the load on the neutral would be 0 amps. If it were then split to three 1 phase 120v circuits the power could no longer return on other phases and will need to return on the neutral. This would increase the load on the neutral wire to 60 amps, twice it's capacity and will certainly fail by over temp.

@charleslane2735 2 жыл бұрын

Are these things surge protected?

@JenniferKrisystin 2 жыл бұрын

sweet

@omenharun Жыл бұрын

Good

@ryanlaingmvp3191 3 жыл бұрын

Neat

@raidensama1511 11 ай бұрын

Are you actually using all 3 phases? Maybe I’m missing something… looks like only two of the three phases (black and red wires) are used off back of your input.

@brucebryant6483 11 ай бұрын

Yes the loads are balanced on all 3 phases. The blue is on the bottom of the flanged inlet. It is hard to see under the ground wire.

@user-dv9zm6iu9x 9 ай бұрын

Good morning. good work and clean where you buy the QO breakers

@brucebryant6483 9 ай бұрын

QOU breakers you can google them. Many suppliers out there. The part numbers are like QOU120 for a single pole 20A QOU350 for a 3 pole 50A

@Shockedbywater 2 жыл бұрын

QO breakers are just like other brteakers of the same size. They are thermal magnetic

@elchache21 Жыл бұрын

Where can I order all those parts

@quaad_heavy_sounds 4 жыл бұрын

Hey! Extremely helpful video. Thanks for putting this out! I've been looking for power distribution solutions and this helped clear up some confusion about the L21-30. Was wondering if you are capable of building a distro for me? If so could I have your contact info? Thanks

@brucebryant6483 4 жыл бұрын

Hey thanks for the comment I'm glad to have helped someone. Email me the details of your project and I'll see if I can help.

@mariosanchez5053 2 жыл бұрын

@@brucebryant6483 can I get your email I need one build for dj use

@luiscastellanos3217 3 жыл бұрын

Hi, will you do some cutout on a 3U panel for me? I’ll pay the price

@sheldonbrammer1209 3 жыл бұрын

Hey where can I find these breaker to buy??

@simodonultimex54 2 жыл бұрын

hey did you find the breakers, a need some too

@robertberry4806 8 ай бұрын

What the prices for that one

@raykaiyum6174 3 жыл бұрын

Where can I find the parts for this

@brucebryant6483 3 жыл бұрын

Amazon, Mc Master Carr, Pro speaker parts for the box. You can get thhn wire at a big box store. Or we can send them to you.

@fitness5 2 жыл бұрын

Hi, Where Can I Purchase The AMP Connectors? Thank You.

@brucebryant6483 2 жыл бұрын

The 90 degree connector caps came from Mouser Electronics MFG P/N 1546349-2

@fitness5 2 жыл бұрын

Thank You.

@raykaiyum6174 3 жыл бұрын

I got 1drive rack 1 exciter 1 band mixer Do controller 2berringer europower 4000 amp 3cvr 1504 amp 2cvr 3002 amp 1 powersoft k10 How much would it cost for u to make a distro to accomadate all that in 1 rack ...?