Hello, i am scene props from Serbia and i am forever thanful youtube recommended your videos.

Bravo! This process is roughly as complicated as a wooden slab set in a mold and epoxied, but this is vastly superior in the end.

Greetings Anak Rantau Interior Multitriplek Plywud from Indonesia 🇮🇩 In my opinion, the curved method is good in this video. However, for me the contractor follows this method. but this video is good and interesting to add insight to me🙏☺️

Really clear instructional video. Thanks for sharing!

Ah!, entiendo, maestro👍, muchas gracias!! Saludo desde en Argentina👊!

Hi, could you please tell me what kind of pump youre using? mine (a cheap model) is, acoording to the instruction manual, not for permanent use (several hours) under pressure. thanks

Buen trabajo saludos de Monterrey nuevo león

too good, very admired

I’m looking for the glue that is used to handle the elements of the outdoors. Do you have any idea the type of glue it is and where to get it?

Perfect technology

Incréible👌!

Thank you very much for the video my friend. It was very helpful.I have a lot of 6 mm plywood in my stock. Can I laminate them on top of each other and thicken them with this method? Is it strong? I want to process it on CNC later. I would be very pleased if you answer.

Ive done a similar thing before - gluing multiple sheets of plywood together to create a curve. It is indeed very strong. As an alternative approach, could you nail the sheets of ply together? I'm not sure if it would retain the same shape that way.

Perfect

Amazang.

How would you go about doing an S shape with this method? Do you have to create styrofoam forms for both sides, or still able to do it with just one side? What method do you use for shaping the foam in the first place?

Would love to purchase these thin ply layers. I can't find them anywhere in this size. Where can I find them. Thanks

It’s a very good video. A few comments The glue spreader shown is very expensive - £100? You can get pretty much the same result - just a little slower - using a normal foam brush and tray The type of glue is important. Go for one that has a longer open life. I use either Titebond Extend or Titebond 3 I use a lot more breather fabric than that shown. I always have this fear about air being trapped. It’s an once only process and so I would rather be safe than sorry There is obviously a ball CER between the severity of the curve required, the thickness of the laminates and the type of timber. Flex plywood is the easiest but if you wanted the shape shown and had no flex ply, you couldn’t do it with 2 x 6mm ply; you might have to use 6 x 2mm. If using “real” timber, obviously go for straight grained where possible; again, try the process out first with all laminates dry. That trial run will show you if your shape can be achieved with what laminates you have chosen; if it fails, then at least you haven’t got a mess to clean up Pre forming can work. By that I mean, put all the laminates in the bag stacked but without glue; sometimes,even wet with water to soften the fibres; vacuum and leave. After a few house, take out and the laminates will have taken (only)part of the shape you want. Now glue and re-vacuum. This method helps particularly with severe shapes or thicker laminates. You are really pre-stressing the laminates. It doesn’t always work. Failures will happen. If you want a shape topped by some expensive, exotic veneer, form the shape in one process with all the laminates glued but no veneer (if it fails, you haven’t wasted the veneer) then re vacuum with the veneer now glued up and in place.

simply GENIUS - thank you for sharing

1:57 A plastic tube and a sleeve (C - channel) are used to seal the bag. I find this very useful. What is ii? Could you elaborate on that.

Какая фанера и клей ? Спасибо.

just come across your video and found it very useful I'm also in the UK but can I ask how much was your bag press please?

very fantastic

I am using this process in a project and I need to know how long this will take. Do you know how long this will take from start to finish?

Will it ever lose its shape? If there's humidity in the air? If it's left outdoors?

So, how much glue ended up in the vacuum line?

Очень хороший метод!

Very good video, thank you. I don't understand why youtubers choose repetitive music that stresses us out. Watch your video beginning to end and you'll understand. Just a suggestion.

The same result I get for several item in the same time using a rachet straps on the templates without need it a pomp. Anyway, the ideea is interesting

How to bend 8mm fly wood into 2 1/2 inch round pipe

Quiero saber, no sé que los tipos de maderas flexibles, cómo se llaman aquellos?, please...

hi sir, what you are using for vacuum bag sealant

POR FAVOR, PODERIAM ME INFORMAR QUAL É ESSE TIPO DE MATERIAL QUE VOCÊS USAM???? POOOOOR FAVOOOOR! RSRS ESTOU DESESPERADAMENTE querendo saber. Muitíssimo obrigada!!! No aguardo.

So your grains are all in one direction when you bend? How to make a bend in 3D ?

Where do you source your wood from?

Presión de vacío ???... Cuántos bares está ???..

How did you cut the radius on the former (is the former foam?)

Sous vide plywood!

Cool! You have a cat house!

What adhesive are you using?

Doesn't the glue need air to dry?

Which machine used for sucking air

تم

Jai Swaminayaran

Nice glue applicator

Hi

“The easy way”...if you happen to have a large vacuum forming machine.

Rugby Sweats! What Club?

This was 1997 all over again. Only how it's made without the narrator.

M

Бб

the easy way i will skip the fancy roller for the glue

The easy way??

Now make a Möbius strip 😂

Sorry but that has nothing to do with laminating wood. change the title