Al credit to you for these videos. I dont think I would have the bottle to tear into mine like that. Glad to have someone doing it all for us.

Fascinating to see how it’s put together, and how easy it is to work on if needed

Hi boys loving your videos been really helpful. Just something I found on the arches of the 2020 defender, those white retaining clips if you stick your hand behind the arch lining and push them from behind they pop out without breaking. And where the push studs are use a flat trim tool and push on those and they pop out to. Keep up the videos boys 👍👍👍👍

Fantastic thanks so much for showing how this lego construction come together really enjoying the series Alan

Thanks so much for this video. I saved about $3500 ordering the replacement passenger headlight assembly on eBay and $1500 on labor. You're doing good work!

Just the right length to watch while I have my Sunday dinner. Great video, as usual , guys.

Great content mate! The Defender doesn’t seem to be built to be worked on and looks quite complicated. It will be interesting to see what if any bullbars the aftermarket (ARB, Ironman, TJM, etc) come up with. Keep the videos coming.👍

I love following your program.

Another entertaining and informative video. Who knew that a plastic lollipop stick would be such an essential tool for the new defender. Land rover will sell branded ones in the store for £50.00 now...

Love your videos. Keep em coming

Admire you just wading in and taking it apart - guess that's why you bought one as a strategic investment to design the accessories and 1st to market! Well done. Entertaining to boot. Am going to start the buzzword bingo now then!

In LR's offical video titled "Reliability" they have mentioned "monocoque structure with steel subframe", so far I haven't seen anyone bothered to find out what that steel subframe is and how much/likely it will improve the much debated unibody monocoque structure but some say it's a semi ladder frame. If you can shed some light on that in your next video I'm sure lots will benefit from it!! Cheers mate

One of 3 channels that automatically gets a thumb up and a share before a word has been spoken. Cheers guys.

this is great video

Hello Simon, can you find out if this ACC Sensor is heated? Today first snow here and mine immediatly stopped working and i could see it has a bit of snowmud on it. Sensors from other Car-Manufacturers i drove had this heated and there was no problem This is used for differnt assistance systems, such as acc, emergency breaking etc Hope you can help THX

I wonder if we can order the Premium LED headlights and install them on the base model, it would save $10K for those that want the nice headlights without having to swap to the v6

Hi 👋 thanks 😊 for another great 👍 video some time look 👀 easy but practical is difficult. Do we need to remove headlight for replace Headlight bulbs 💡. Thanks 🙏

It looked like the small white panel below the black light saround could of been removed first with your white hand tool and then as you said take the black headlight saround towards the middle of the car . Maybe 🤷‍♂️ . Good vid chaps 👍

Can you do the radio next. I keep loosing sound to radio and Spotify cones n go

Interesting video as usual. Two schools of thought here, the advantage of repairing small "bumps" at home but the downside of replacing many expensive parts due to a larger impact. Although if I had to choose as a pedestrian being hit by one of these or the old Defender, the answer is obvious.

You're an interesting man

The ring round the headlight is harming back to the angel eye headlamps BMW created in the nineties, would look good if they were the DRL though. Full LED headlights don’t require washers, I’ve got quad LED headlights and no washers in sight. Love these videos, probably the best on you tube as every one is a journey of discovery and all the better for not being fully rehearsed.

You need to install the roof rails... Lots of potential for goodies up there.

Are you planning to wrap the front white panel you’ve just taken off to match the A-pillars? Might look good...

Today’s video was brought to you by the colour orange and 29 Gary’s. Great channel - got to know these guys via a Toyota cambelt video a few years back and there were many shoutouts for Tom in that video 😜

The US site appears to be missing the Factory Winch when you attempt to build a model. Hopefully you will install a winch and show us how? :)

I’d like to switch out the green Land Rover emblem for a black one. Are you guys planning to make one? Or do you know the part number for one with radar?

That looked like a fiddle to get those light surrounds off. I’m putting in a plea for you to design a replacement bottom panel shroud (the black plastic bit below the silver lower grille) to leave the front towing eye accessible. I was considering taking a Dremel to mine but a replacement part would be better. At the point at which you need to access the front towing eye off road, there’s no way you’d be able to unscrew the metal bolts that hold it on.

Well Simon when you come to sell that motor all the bolts and nuts you need to take off to get to things will have orange paint on them so people know where they all are Ralph Cooling 👍👍

I woulf like to see if you can remove the RHS light surround without cracking it?

South Main Auto, This Old Tony and Forgotten Weapons. So thats 4!!!

Hi guys! Is there a website you following for disassemble the new Dedender?

Who would have believed the Defender would be re-born as a Tupperware princess ? 😂😂

Well, with removing the grill and headlight surround, your about a 1/4 of the way from installing the front LR metal skid plate. To continue installing the metal skid plate, remove the 5 screws from along the top of the bumper cover (exactly the same as the one for the headlight surround). Then remove the forward section of the wheel well cover by removing the 4 Phillips screws and the 3 push clips. Once the forward plastic liner is removed, fold the tab out (one of the Phillips screws when through the tab). There are 4 screws along the bottom of the cover (torque screws with large washers... screw is same size used to remove the 4 at the top of the grill) Then with someone helping, give a good yank on either end of the bumper cover where the metal fender meets the plastic cover. Then, remove the brake ducts (2 push clips each), remove the push clip for the coolant hose from the metal bracket (the hole just below the one used for the brake duct), remove the 2 13mm bolts (they go up from the bottom behind the bracket and these can be discarded as there are new ones in the skid plate kit) and the two lower front facing 15mm bolts. Keep the 2 15mm bolts to reuse. Remove and discard bracket. Also remove the 2 15mm bolts from the existing lower skid plate and discard. Install the new bracket with supplied hardware. Reinstall the front bumper cover. Install the metal skid plate and secure with new hardware (two torx head bolts go to the front, the longer 13mm head size bolts go at the very bottom (where you removed the front bolts from the existing lower skid plate). Reinstall headlight surrounding, grill and finish cover.

👌👌👌👌👌👌

لقد استفدت منكم لطريقه الفك 👍🇵🇸

Hi! When will the mini cooper r50 matte grilles be back in stock??

Is there actually a secrete way to replace the badge on the front grill from green to black version?

Pa, 1100 quid? Is that plus vat? So a small front end bump smashing that sensor when its 4 years old will make it a write off!

Any plans to show how to remove the silver section of the front bumper for those that want to colour code it?

DOES THE BODY NEED TO BE LIFTED OFF TO CHANGE THE ALTERNATOR OR ANY OTHER COMPONENT

Where can I get a hold of the manuals

Do you have to do all that to change bulbs?

What program is that ? How are you able to view disassembly PDFs?

Please do headlamp guards! just had to pay £1400 for a new unit because of a cracked lens!

Omg. I'd have the lr3 09 stripped and rebuilt in that time. Check out the lr3 light bulb change, it's so easy. Why defender, why?

Would be good to see you fit a front winch.....

How to change a headlight bulb on a new 2020 defender 🤔 😳.

Good jobs lads have a drink on me👍

How to wreck a new defender one flimsy plastic bit at a time! Land rover are so far removed from their roots that they only know how to design plastic parts for luxury cars. It could have been brought up to date with plastic parts but held together with say push rivets that had a landrover logo on the top like a lego brick stud. It could have been a design feature, You could remove the parts and if any fixing broke it would be a rivet that you could replace rather than an integral part like the edge of the trim panel which is never going to be the same once you have broken the clips.

Wow. The Chinese will love reverse engineering this car. It’s so intricate and complicated!

In Australia these things start at $113,000 AUD for a 2.0 Td. I’ve just bought a brand new 76 series Landcruiser with a 4.5lt V8 TD for $71,000. And guess what, the bumper is bolted on! I’m sorry, you’re not selling me on the defender.

Pretty tough just to change a bulb.

*

No Steel Grill to double as your barbecue when in the outback !!!!!!!!!!!

it's friday it's 5 o'clock it's crackerjack

It's unreal that he don't have the stock front push bar/grill install video!!!!!!

His he looking at me or you

The most British of cars, a Defender, and it's built in Slovakia. How long before JLR are Chinese?????

£1110 for the front grill ! It’s going to be an expensive repair if it gets bumped. Surely you can come up with a retro fit with a light bar fitted for far cheaper than that.

Tonka Toy Town.

£1100 for a sensor plus VAT no doubt...FFS........and it wouldnt take much to destroy it, a minor shunt.

You can see, one minor bump and all those little plastic bits will need replacing , headlight looks quality if you like Airfix kits. It's just another modern car now, why have JLR done this? Turned a light commercial truck into a plastic suv, my prediction is that it will go the way of Disco 3 , bargain basement overcomplicated, unreliable used car, at least the Disco 3 was good looking.

So much plastic - at least it won't rust 🙄

Plastic, plastic and more plastic. Will all fall apart at the first tap. Entertaining video, shame about the toylander

Holy cow look at all that plastic..wow..so much like the previous Defender.. : /

the fact that you are exposing the terrible generic trash this car is made out of on a daily basis , whilst thinking your promoting it for lr is comedy gold , ps stop deleting my comments you said you like critisism!

cheap plastic everywhere

Blimey cheap plastics everywhere

Sírok... Sok-sok műanyag patent, öt év múlva a fele törött... Ez az autó már nem terepjáró, a sár kimoshatatlan ennyi apró műanyag alkatrészből...

cheap plastic.

Plastic defender....plastic....plastic

This guy is a hell of a guy I must say..but Land Rover has freakin lost the plot completely. Are there no genuine British at Land Rover anymore ? What kind of Off Road vehicle can this be with the whole front "bumper" made of plastic. To change head light ..it's not a matter of changing a bulb right..its a matter of changing that whole plastic contraption at the price of a decent American Standard Fender Stratocaster..what kind of Defender is that !!