If you would like to purchase one of these maps check out my etsy store! www.etsy.com/listing/13345138...
Пікірлер: 28
@diva65ir Жыл бұрын
Looks great! I like how it shows the details
@munro43989 ай бұрын
Funny. This video came across to my feed, and I was finally watching the map and realized that it's my hometown. Hilarious
@thomasl.1425 Жыл бұрын
Great job! 👍
@vcap7886 Жыл бұрын
Great Job! I'm looking to buy a laser. You make this look so easy navigating around those different software programs. Subscribed!
@carolinaworkshop7091 Жыл бұрын
It really is easy. I spent an afternoon playing with this stuff to figure it out. What you saw me do in Adobe illustrator is the extent of my knowledge of that software. That's the only thing I can do with it.
@vcap7886 Жыл бұрын
@@carolinaworkshop7091 thank you for this!
@fitzoune Жыл бұрын
J’adore et j’aime ce que tu fais, merci de France
@occisoft8082 Жыл бұрын
Looks good
@pwnr8r Жыл бұрын
Wow
@nyshodogАй бұрын
Wait that was a four and a half hour burn wow!
@carolinaworkshop7091Ай бұрын
Generally, for a through burn on 1/4" material the speed is like 150mm/minute x 2. So yea 4 hours is about right with this much detail. This is a 10watt diode laser.
@user-gi9nd2jn7d Жыл бұрын
How do you make the highway cut that attached to the frame look? Thank you.
@jakerazmataz852 Жыл бұрын
I'm going to do these maps. My question is, what size is the most popular? Of course I can get them in bulk the same size cheaper than 10 of this 10 of that. I was going to go with 12x12. I think that's a good starting point. What do you think?
@tomcaki7454 Жыл бұрын
Hello sir, amazing work!! If I may ask, what spray are you using in the end please?
@carolinaworkshop7091 Жыл бұрын
It's an oil based polyurethane. It protects the wood a little
@ChrissRollex2 ай бұрын
How the pictures fit to the frame ? From the back side is Okey it have a holders..but from the front side ? How ?
@benjaminl3084 Жыл бұрын
Thanks for sharring! What laser are you using for this?
@carolinaworkshop7091 Жыл бұрын
Ortur Laser Master 3 10 watt. I don't have experience with any other laser but I like this one
@benjaminl3084 Жыл бұрын
Do you have the extension kit?
@carolinaworkshop7091 Жыл бұрын
@@benjaminl3084 nope. Have not had a use for it
@davidgruty11 ай бұрын
what are these last metal pieces you use in the back to fix the board? how are they called?
@carolinaworkshop709111 ай бұрын
The things that hold the picture to the frame are called glazier points or glazier push points. The piece that holds the frame to the wall I just call picture hangers.
@davidgruty11 ай бұрын
@@carolinaworkshop7091 great thanks
@stalldrom7 ай бұрын
5000 dollar saw, 5 cent work shoes.
@carolinaworkshop70917 ай бұрын
When you look this good it doesn't matter what you wear.
@mirkomantovani608711 ай бұрын
hello
@charlesgarner95398 ай бұрын
Everytime I see this type of video , I get a chuckle at "it's easy to do". I have been into lasers for a long, long time and "it's easy to do" is misleading. If someone is thinking about getting a laser, understand that what you see in this video will require you to become proficient in the use of three seperate software programs. The learning curve for Light Burn alone is effort , let alone two more levels of software on top of it. "it's easy to do" is purely subjective