LaserGRBL In Depth Tutorial - Part 1 - Interface and Control Plus Engraving

  Рет қаралды 79,714

Middle Room Workshop

Middle Room Workshop

Күн бұрын

In this video, I will show you Part 1 of an in-depth Tutorial on LaserGRBL software.
Part 1 will cover the interface and control of the machine as well as the engraving workflow toward the end.
The machine in the video is a NEJE Master 2s Plus with a 40W Dual laser module.
My Blog where you can find content related to Laser Machines and Engravings as well as free 3d accessories, testing templates and projects for your laser engraver :
whathowwhysolution.com/laser-...
Machines:
Latest Laser Engraver and 3D Printer Offers affiliate.geekbuying.com/gkba...
Atomstack
Official - All machines
P7 & P9 s.click.aliexpress.com/e/_DCr...
A5 s.click.aliexpress.com/e/_DeE...
A10 s.click.aliexpress.com/e/_Dml...
X20 s.click.aliexpress.com/e/_Dd0...
X30 33W Laser s.click.aliexpress.com/e/_DDP...
Amazon
amzn.to/3OqnGLF
amzn.to/3ERIQiY
amzn.to/3OrnZG0
Aufero & Ortur
Laser 1 s.zbanx.com/r/7ONL70JFNkci
Laser 2 s.zbanx.com/r/8BshexpB5gsN
Laser Master 2 Pro s.click.aliexpress.com/e/_DkA...
Laser Master 3 s.click.aliexpress.com/e/_DDk...
LU2-4-SFLaser module s.zbanx.com/r/tnuGpccNPxBi
LU2-4-LF Laser module s.zbanx.com/r/QOp6rfiVguw6
Amazon
amzn.to/3TVw9rz
amzn.to/3tQfA5Q
NEJE
Official - All Machines shareasale.com/u.cfm?d=886868...
NEJE 3 PRO s.click.aliexpress.com/e/_9waC1r
NEJE 3 MAX s.click.aliexpress.com/e/_9ynf3X
Amazon
amzn.to/3AA5cTj
XTOOL
Official - All Machines
EU: eu.xtool.com/?ref=MRW&...
USA: www.xtool.com/?ref=MRW&...
D1 amzn.to/3ERfAIM
D1 PRO amzn.to/3AA5cTj
XTOOL RA2 PRO Rotary amzn.to/3AyWiFB
Longer Ray 5W & 10W
s.click.aliexpress.com/e/_Dej...
Amazon
amzn.to/3TSZCSL
amzn.to/3OsnYC4
Other Brands
Comgo Z1 s.zbanx.com/r/369OUFEJ2Tun
Atezr P20 Plus amzn.to/3UWSTIV
LaserPecker 2
s.click.aliexpress.com/e/_Dd6...
amzn.to/3VjRWKJ
OMTech CO2 Laser amzn.to/3Vd053p
Sculpfun S9 amzn.to/3ERfAIM
K40 CO2 Laser s.click.aliexpress.com/e/_DmW...
Accessory:
Ortur Rotary Roller s.zbanx.com/r/KEvEr5qpnB6X
Offline Controller s.zbanx.com/r/H7Qfwt9eiJO3
Aufero Laser Height Adjustment s.zbanx.com/r/tl634XxCxKsg
XTOOL RA2 PRO Roller s.click.aliexpress.com/e/_DlL...
Atomstack Roller: s.click.aliexpress.com/e/_DeM...
Atomstack Extension: s.click.aliexpress.com/e/_DBA...
Timestamp
00:00 Start
04:27 Left Section
07:21 Jogging control
09:16 Lines Count & Estimated Time
10:43 Speed and Power Override
12:04 Reset Button
12:13 Home Button
12:32 Unlocking Button
13:24 Quick Action Button + Custom Buttons
13:54 Set Zero Button
16:05 Center Button
16:27 Corner Button
16:41 Frame Button
17:40 Focus Button
18:17 Blink Button
18:46 Submenus
19:20 Material Database
21:00 Hot Keys
21:44 Send to Machine
21:50 Send From Position
22:42 Change Color Theme
23:58 Update
24:14 Session Log
25:04 Engraving
26:23 Setting overrides while engraving
See Also:
LaserGRBL In Depth Tutorial
Part 1 [Interface and Control Plus Engraving]: • LaserGRBL In Depth Tut...
Part 2 [Open, Append & Save gcode files + Hint]: • LaserGRBL In Depth Tut...
How to cut large sheets
• Cut Large Sheets of Pl...
How to test your machine and materials in one Go
• Test your Laser Machin...
Safely home your axis
• Safely home your laser...
How to cut Leather
• Can you Cut Leather wi...
What is G-code
• What is G code
Laser Problem
• Laser Flashing Problem...
Can you engrave Metals?
• Can you Engrave Metals...
Upgrade the Neje Master with the 40W Dual Laser Module
• Neje Master Upgrade -...
Automate Layering in LightBurn using Inkscape or Autocad
• Automate layering in L...
How to engrave custom fonts with the Neje Desktop App
• How to Engrave Custom ...
See Also the in-depth tutorial of Neje Desktop App
• Neje Desktop Applicati...
See Lightburn vs Neje desktop App
• Lightburn - Editing an...
See also Useful upgrades for your Laser Cutting and Engraving Machine:
• Useful upgrades for yo...
See where you can find Project ideas ready to download:
• Project Ideas and Down...
See how to find the right cutting height and Quickly Focus
• Find the right cutting...
Set up J Tech photonics extension for Inkscape:
• NEJE Laser Machines an...
See how you can engrave custom projects with Inkscape:
• Laser Engraving custom...
See how to engrave custom projects with AutoCAD or LibreCad:
• Laser Engraving and Cu...
See how to create projects that combine engraving and cutting:
• Combine Laser Cutting ...
See how to control your NEJE machine through your smartphone:
• Laser Engraving and Cu...
Thanks for watching

Пікірлер: 65
@SergioMendez-mb9zg
@SergioMendez-mb9zg Ай бұрын
I really appreciate your time and patience to help the people like me that are in zero knowledge of this software and with this tutorial I'm getting ready to rock and use the right way my brand new laser engraver. Thank you so much.
@agghell224
@agghell224 11 ай бұрын
One of the best videos about using lasergrbl, very detailing and good explained. Thank you !!!
@ezexcel2732
@ezexcel2732 Ай бұрын
thank you, good explanation
@CrazyFuzz8
@CrazyFuzz8 Жыл бұрын
I am so grateful to you. Here's exactly what I needed to know. Thank you 👍🏻
@Mcso1560
@Mcso1560 Жыл бұрын
Thank you so much for taking the time and sharing your knowledge. I've been starting laser engraving for 2 months with Grbllaser and without a doubt, this is the best tutorial among the ones I've watched. I will watch the others. God Bless!
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi Mário Sena, thank you for your comment and compliments. I am glad you found my content helpful. Ciao
@kennethfell2511
@kennethfell2511 Жыл бұрын
Awesome video (s), I changed the factory settings on the QUALITY/LINES/MM. What is the default number. For some reason I changed mine to 4.000. I see on yours it's set to 10.000. Ortur Lm2 20 W & Lm2 S2 20. Thank you.
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi @@kennethfell2511; thank you for your comment and compliments. I think 5 is the new installation value, but there is no default value. Generally, around 5-10 lines per mm yield good quality engravings. You can calculate or approximate the required quality by knowing the focus spot size of your laser module. Most laser modules produce a spot around the 0.1x0.1mm; therefore, with 10 lines per mm, you cover the surface nicely, but if your size is smaller, say 0.06mm, then do 1/spot_size and approximate for a lower value. The example would be 1/0.06=16.67, which I would approximate to 15. I hope it helps Ciao
@bullswoodworks8398
@bullswoodworks8398 3 ай бұрын
YOURE A REALLY GREAT TEACHER DUDE! SUBBED!
@harshaa5745
@harshaa5745 Жыл бұрын
clean and clear thank you so much
@mohamedmokdad5222
@mohamedmokdad5222 Жыл бұрын
Many many thanks for these high quality tutorials on LaserGRBL interface. Very explicit and clear explanations. These help me a lot with my newly acquired ATOMSTACK laser engraver. Having great fun thanks to your tutorials. Awaiting new tutorials from you, please, go ahead.
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi, Mohamed Mokdad; thank you for your comment and compliments. I am glad you found the content of my videos helpful. Below you can find the entire playlist about LaserGRBL. kzfaq.info/sun/PL--bqtBHPhQNXepHzuGzv8MW1L7whZ6I8 Ciao
@maciejcuprzynski9367
@maciejcuprzynski9367 Жыл бұрын
Great job. Thanks
@firstpitstop
@firstpitstop Жыл бұрын
Great info here. I have a question where can I get the shortcut buttons you have like the frame? I need these and wondering if you have or know of a video to add these. Thanks
@spudhut2246
@spudhut2246 Жыл бұрын
well done, thank you. More information is greatly appreciated.
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi, Spud Hut, thank you for your comment. I got an entire playlist about LaserGRBL; you find it here: kzfaq.info/sun/PL--bqtBHPhQNXepHzuGzv8MW1L7whZ6I8 Ciao
@scorpianspirit5124
@scorpianspirit5124 10 ай бұрын
Really well done tutorial, this was a big help ! Thumbs up ;-)
@quickshare333
@quickshare333 Жыл бұрын
Hello, nice tutorial.I want to ask a question, I recently buy twotrees laser engraver and when I set something to engraver and put it horizontal lines without additional options the picture is good on the corners but in the middle is double and with less power whether are words or else to engraver.If it's vertical engraving is good on all materials.Did I miss something...
@user-vf1wl5wz9o
@user-vf1wl5wz9o 10 ай бұрын
thank you
@landyandy
@landyandy Жыл бұрын
I've been using LaserGRBL for a long time but lately I needed to use a feature I've never tried. "SEND FROM POSITION" asks me which line to start from. The question is, is there in the software the ability to figure out which number to insert based on the uploaded image? I tried to move around the image by double clicking and the laser positioned itself correctly but I thought it would also show me the corresponding line to start from. Can you give me some suggestions? Thanks and congratulations for the video.
@thejyhansenergy8424
@thejyhansenergy8424 6 ай бұрын
👌👌👌
@ginaswann9983
@ginaswann9983 2 жыл бұрын
2 videos in and I'm learning so much! Thank you for these! But did I miss where we set our x0 y0? I can't seem to find the answer anywhere. Mine is the far right corner.. so on my computer screen I only see a small portion. I can not see the whole X and Y axis. Like yours- +
@MiddleRoomWorkshop
@MiddleRoomWorkshop 2 жыл бұрын
Hello Gina Swann, thank you for your comment. If you are working with Gcodes, then the origin, i.e. the x0,y0 is given by the software you used to generate the gcode file, in this case, you will need to correctly place your geometry in the original software before exporting the file, if you are using an Inkscape extension put the geometries the x0,y0 position in the canvas before exporting. If you work with images (part 3 of my tutorial), then you are prompted in the final wizard to locate your origin under the size input fields. Let me know if is all good with that. Ciao
@henriquecavaca8126
@henriquecavaca8126 Жыл бұрын
Hello, great videos, the part 1 and part 2. Very well explainded, thanks. I do have a doubt about the 3 buttons which you can increase the power and the speed of your work, but the 3 the button, what you can change with this button is ( Rapid) ?
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi Henrique Cavaca, thank you for your comment. This are parameter overrides that can be adjusted while you are engraving or cutting. The third slider labelled Rapid is the speed of the axis while not engraving; that means when the laser head moves from one engraving region to another without engraving, also known as whitespace, in this case, you can tell the machine to move faster since it does not affect the engraving result. However, the faster the movement is, the lower the quality could be because the laser head needs more distance to slow down. This is normally compensated by the application, but if you notice some miss alignment this Rapid move could be the cause. Ciao
@pulkitgoel3877
@pulkitgoel3877 2 жыл бұрын
i need GRBL. setting... on acrylic sheets.... engraving..
@nenadtodorovic7739
@nenadtodorovic7739 2 жыл бұрын
Thanks for great tutorial! I have a problem that my laser won't fire. I set the ''home'', it's well connected and when I start engraving, the laser is moving like it's engraving but without fire. Can you help me with this? Thanks!
@MiddleRoomWorkshop
@MiddleRoomWorkshop 2 жыл бұрын
Hello Nenad Todorovic, thank you for your comment. With reference to the video you are commenting on, If you correctly include the power settings in your generated code, then this behaviour might be the result of a wrong power setting, but before that try to open the gcode file with the notepad and have a look to where it says M03 or M04 and what is the parameter next to it, it should be something like S100 to S1000 which corresponds to power 1 to 100%, perhaps the software you used to generate the gcode did not correctly include the power settings. I that is the case you have to check why the originating software is not providing the right power, if you are using the JTP extension in Inkscape, you need to set the power and the mode in the export wizard. Let me know, hopefully, that is the issue. Ciao
@nenadtodorovic7739
@nenadtodorovic7739 2 жыл бұрын
@@MiddleRoomWorkshop thank you for response!
@dirkroberts525
@dirkroberts525 Жыл бұрын
I am usisng a latitool f50. Using lasergrbl. NO CONFIG settings imported from the machine. How do I fix this? Why is there no support number listed?
@ARMA2ARMENIA
@ARMA2ARMENIA 6 ай бұрын
👍👍👍👍👍
@REGINALDO369
@REGINALDO369 2 жыл бұрын
hello, my grbl 4.8.0 software, when I record it, there is a lack of buffer and the machine stops. Do you know how I solve this? thanks.
@MiddleRoomWorkshop
@MiddleRoomWorkshop 2 жыл бұрын
Hello REGINALDO GOMES, thank you for your comment. I have helped some other subscribers with this issue, and it turned out that the installation did not go well. I do suggest you uninstall the software, re-download it from the LaserGRBL site and install it again. Let me know, Ciao
@ciromartello6843
@ciromartello6843 Жыл бұрын
hello kindly I bought a sculpfun s10 and I'm using lasergrbl without problems but I don't know how to do something by chance a wooden keychain with the engraving and the final cut of the piece with the appropriate hole to put the iron circle as it is done thanks settings
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi, Ciro Martello; thank you for your comment. I replied to your Email a couple of days ago, but I am just pasting my reply back here. QTE*** Just confirm my understanding; are you trying to do a project (a key chain) with both Engraving and Cutting? Sei Italiano? Se si possiamo comunicare in Italiano. UNQTE*** Ciao
@tolgafutaci
@tolgafutaci 2 жыл бұрын
Hello. Great video. Thanks. But i have a little problem which i couldn't solve. My axis are reverse and not going the correct side. How can i invert them? Thanks in advance and my best
@MiddleRoomWorkshop
@MiddleRoomWorkshop 2 жыл бұрын
Hello Tolga Futaci, thank you for your comment. This should be an easy fix. Have a look at my FAQ page where I explain how to reverse the axis. whathowwhysolution.com/when-clicking-on-the-home-button-the-machine-goes-in-the-opposite-direction-lasergrbl/ Let me know if all is good. CIao
@tolgafutaci
@tolgafutaci 2 жыл бұрын
@@MiddleRoomWorkshop Hello again. Thank you for the reply.. It looks like I've solved my problem.. I bought my cnc from someone and realised that, they connected the x axis socket in a wrong plug.. I fixed it when switched the ports..
@saasaasaasaa9926
@saasaasaasaa9926 Жыл бұрын
❤❤❤
@fiascofishing5345
@fiascofishing5345 2 жыл бұрын
It looks like you have this software really figured out. I am new to this and was watching your videos and doing well then all of the sudden all of my images I import are all red lines. there is no images seen. the laser just does red lines. I am sure I must have changed something. do you have any thoughts.
@MiddleRoomWorkshop
@MiddleRoomWorkshop 2 жыл бұрын
Hello Fiasco Fishing, thank you for your comment. I think it has to do with the combination of parameters and the power mode set to M3 in the final window. Let me know if you have been trying to change the simple parameter like Brightness and Contrast, or paraphs you checked the B&W with low clipping or using the Passthrough. Let me know in order to troubleshoot further. Ciao
@fiascofishing5345
@fiascofishing5345 2 жыл бұрын
@@MiddleRoomWorkshop i tried this a number of times. I tried again and adjusting the brightness worked. Thank you
@dailyshop4634
@dailyshop4634 2 жыл бұрын
Sir I have two questions. 1st.. is it possible any laser engraver work with coreldraw software.. 2nd... when I load file in laser grbl software my file size show bigger than what I export from coreldraw..it becomes change
@MiddleRoomWorkshop
@MiddleRoomWorkshop 2 жыл бұрын
Hello daily shop, thank you for your comment. I am not an active user of Corel Draw, but I know that there are certain plugins to work with CNCs machine like the laser engraver. The reason why you get some scaling when importing files is due to the measurement system used, GRBL is a unitless program, meaning that 5mm is the same like 5" or 5Km the software cares only about the number part. So in Corel, simply change the unit to mm and you should be good to go. Ciao
@baileyking9487
@baileyking9487 2 жыл бұрын
how do you see the full cartesian plane on the interface?
@MiddleRoomWorkshop
@MiddleRoomWorkshop 2 жыл бұрын
Hello bailey King, thank you for your comment. You will be able to see it once you open a file, unfortunately, you cannot edit it or move it. It is a gcode file, the origin will be wherever it was in the originating software, while if you import images, then you can choose an offset for the origin. Have a look at parts 2 and 3 of the tutorial you will see how it works. Ciao
@user-bi7xw2ov8u
@user-bi7xw2ov8u Жыл бұрын
Hello, I would like to ask about the configuration fee. The machine cuts very slowly. When the cut is complete, return to the starting point. Motor likes to freeze. Thank sir.
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi, แคคตัสซอกลุงอ้อ, thank you for your comments. Please tell me what machine and software you are using. I can give you some parameters for the cutting, but I need to know what material and the power of your laser module. Let me know Ciao
@user-bi7xw2ov8u
@user-bi7xw2ov8u Жыл бұрын
@@MiddleRoomWorkshop 3018 minicnc and lasergrbl 1.1h
@quillmaurer6563
@quillmaurer6563 Жыл бұрын
Question - possibly one of those questions too stupid to find online: How do you tell it which preset from the material database you want to run? This video doesn't show that, and I've scoured the internet and dug through every menu trying to find that, not finding anything. How do you select say "Hardwood - cut" or "leather - engrave"?
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi, Quill Maurer; thank you for your comment. The Database is just for reference. You cannot really assign its parameters to the project. Just read the parameters and then manually input them into the project. Note. I would not recommend using its values, especially for cutting; it is not ideal to use the laser at 100% power as this will affect its longevity; I'd recommend you test your laser with the material you intend to cut or engrave and then use that for reference. Below are a few useful links to the templates whathowwhysolution.com/category/manufacturing/laser/laser-testing-templates/ kzfaq.info/get/bejne/rrl9lrN3u5uod40.html I hope it helps Ciao
@quillmaurer6563
@quillmaurer6563 Жыл бұрын
@@MiddleRoomWorkshop After making this comment, I found more hints that it sounds like these parameters are set in Inkscape (via laser cutting plugins), laserGRBL doesn't really do much other than run them, is that correct? My only prior experience with laser cutting was on a more industrial-scale CO2 laser that was controlled by ThunderLaser RDWorks that can do a good bit more within that program, so this entire workflow is a bit different from what I expected.
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi, thank you for your feedback. Yes, if you intend to work with gcode files, the parameters i.e., Power and Speed, are set by the source software that generates the gcode; therefore in your case Inkscape through that plugin. However, if you work with Raster files or directly .svg, then LaserGRBL will prompt you to input the parameters. If you are looking for software that gets close to what you already experienced, I would recommend LightBurn kzfaq.info/get/bejne/o9mIgMmKl7ORm2Q.html, It costs around 50$, but you won't regret it. It will save you a lot of time and frustration. LaserGRBL is a free alternative but requires more work around the files. Another free alternative would be LaserWeb designed for laser and CNC routers kzfaq.info/get/bejne/jpamZtarnp7WioU.html Ciao
@quillmaurer6563
@quillmaurer6563 Жыл бұрын
@@MiddleRoomWorkshop Thanks. I think I'll figure out how to do it in Inkscape, I'll need some time to learn (I would anyway to create the images in the first place). This just wasn't the workflow I'd anticipated, as what I'd worked with before had that set - and some rudimentary design capabilities within - the laser software. I knew the process was Inkscape to this to the laser, I'd just thought that more of the process happened in LaserGBRL and less in Inkscape. It's all the same steps, just where in the process and via which software said steps occur that isn't what I expected.
@tishcunningham1806
@tishcunningham1806 8 ай бұрын
How do I get the cross arrows
@MiddleRoomWorkshop
@MiddleRoomWorkshop 8 ай бұрын
Hi, @tishcunningham1806; thank you for your comment. If you mean the axis intersecting at the centre of your project, you can do that in the Target Image window where you set the power and the speed; in the bottom section, there is the Offset field with two buttons next to it, the one with the cross will basically give the project a 50% offset for the x and the y axis. I hope this helps Ciao
@andrewearl9315
@andrewearl9315 8 ай бұрын
I can't get my laser to connect it was working then the connect stopped
@MiddleRoomWorkshop
@MiddleRoomWorkshop 8 ай бұрын
Hi, @andrewearl9315; thank you for your comment. It may be something with the port being busy. Try to restart the software. If this does not help, restart the machine. If the problem persists, close the software and ensure it is not running in the background. Use the task manager for this. Additionally, try changing the USB cable and the port to your PC. If you are using a NEJE machine, the machine may be stuck in NEJE mode, and you should use the button on the main bort to toggle between modes. Let me know how it goes. Ciao
@andrewearl9315
@andrewearl9315 8 ай бұрын
I did try some of your simplest options but no Luck. I JUST BOUGHT LIGHT BURN. LOL.......THANKS
@MiddleRoomWorkshop
@MiddleRoomWorkshop 8 ай бұрын
Hi, thank you for your feedback. I guess that is the best option. LightBurn won't disappoint and make your journey more enjoyable ;) If you still wish to try, you can reinstall LaserGRBL; some people solved the problem that way. Good Luck with your new hobby. Ciao
@rogelioegas3789
@rogelioegas3789 Жыл бұрын
Is GRBL work offline to? Thanks
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi, Rogelio Egas; thank you for your comment. The offline functionalities depend on the machine. I hope it helps
@pulkitgoel3877
@pulkitgoel3877 2 жыл бұрын
hello
@brightsides6581
@brightsides6581 Жыл бұрын
My COMPORT doesn't show up
@MiddleRoomWorkshop
@MiddleRoomWorkshop Жыл бұрын
Hi, BRIGHT SIDES; thank you for your comment. If it does not show up, try installing the driver CH340 or CH341. In LaserGRBL, go to "Tools" > "Install CH340 Driver". Often time this fixes the problem I hope it helps Ciao
LaserGRBL In Depth Tutorial - Part 2 - Open, Append & Save gcode files + Hint
20:14
3018 PRO - Setting up your laser
31:50
James Dean Designs
Рет қаралды 336 М.
Тяжелые будни жены
00:46
К-Media
Рет қаралды 5 МЛН
КАРМАНЧИК 2 СЕЗОН 5 СЕРИЯ
27:21
Inter Production
Рет қаралды 575 М.
О, сосисочки! (Или корейская уличная еда?)
00:32
Кушать Хочу
Рет қаралды 8 МЛН
g-squad assembles (skibidi toilet 74)
00:46
DaFuq!?Boom!
Рет қаралды 10 МЛН
LaserGRBL Tutorials - Features and Functions
32:08
Anthony Baltazar
Рет қаралды 180 М.
Centering your Laser in LaserGRBL
14:47
Tony Paolillo
Рет қаралды 64 М.
7. Getting Started in LASERGRBL ! FREE Laser Engraving software!
17:36
Laser engraver laserGRBL
20:30
#ДелайВсёСам
Рет қаралды 107 М.
LaserGRBL In-Depth Tutorial - Part 3 - Open, Manipulate & Append Image files
28:02
LaserGRBL Tutorial 4   Setting up your greyscale engraving part 1
32:48
Anthony Baltazar
Рет қаралды 121 М.
Are cheap laser cutters safe?
18:11
Maker's Muse
Рет қаралды 331 М.
12. How to Engrave & Cut in LASERGRBL . ORTUR LM2 PRO !
19:11
DiSignsCdn
Рет қаралды 119 М.
Top 10 Laser Engraving Pro Tips - Acrylic
17:35
Laser Engraving 911
Рет қаралды 75 М.
Эффект Карбонаро и бумажный телефон
1:01
История одного вокалиста
Рет қаралды 2,6 МЛН
#miniphone
0:18
Miniphone
Рет қаралды 11 МЛН
Индуктивность и дроссель.
1:00
Hi Dev! – Электроника
Рет қаралды 1,5 МЛН