Layered project design in LIGHTBURN

Рет қаралды 9,413

9 ай бұрын

Bringing you along for a file design that I am working on for Brandy. This design is going to require 3 layers to make it complete.
For templates that I have made, check out my Etsy shop. I build files for projects and tools for laser engravers.
theclackshack.etsy.com
For Clack Shack shirts, check out my store:
the-clack-shack.creator-sprin...
The links below are affiliate links that will direct you to the product in this video. If you use this link for a purchase, I will receive a commission from the purchase. I remain unbiased and honest in my assessment as always.
The Clack Shack on Amazon= www.amazon.com/shop/theclacks...

Пікірлер: 39

@woodknack1 5 ай бұрын

I like the three layer one. you need to put the 45 degree lines on the outside trim of that door like you did on the one layer one you did.

@TheClackShack 5 ай бұрын

Yea. I also should have added an edge to hold the lid in place on the CNC one. My files tend to improve over time as I tweak them. Thanks

@chucklenz9011 9 ай бұрын

Hey! put the 2panels on the bottom as glue on attachments. Go look at your door they are raised, as in a “raised panel door”. The should be on the same plain as the door handle.

@TheClackShack 9 ай бұрын

I was going by the design that Brandy sent. I am gonna make my own mini door on the CNC, it will be more like a real door.

@genabush4619 5 ай бұрын

I like the layered one a lot but I also like the offset around the six windows like you did for the single piece. Thanks for the video!

@TheClackShack 5 ай бұрын

Very welcome

@larrycolson7451 8 ай бұрын

Multi layer is my choice! Great job Dave! As always, thanks for the lightburn experience.

@TheClackShack 8 ай бұрын

Thanks...

@DavZell 9 ай бұрын

An idea crossed my mind at the end. If the middle layer (door) had a solid lower half and it were sized so it could open outwards, it could swing open revealing a cat, dog, message, name, year, etc on the lower door portion of the back layer. To make the door swing, you could give it two tabs at the top and bottom that could be sanded round and sit between the front and back layers to form pivots. The back layer could just be the frame and whatever you wanted on the lower half of the door as a silhouette, or it could be solid with the window area shaded and words/etc on the lower half. Sorry if that was wordy or hard to understand!

@TheClackShack 9 ай бұрын

That could be done. I was reproducing what Brandy wanted.

@DavZell 9 ай бұрын

@@TheClackShack oh, yes; I knew that. I thought my post might give some9ne an idea to try. Hope you feel better soon! We don't want to see you in the Cla-spital.

@mr.mrs.t.9292 8 ай бұрын

Another great educational video . Thank you so much!

@TheClackShack 8 ай бұрын

Thanks, glad you liked it

@isaiahgillett2573 9 ай бұрын

Love the layered door. The engraves wasnt bad either.

@TheClackShack 9 ай бұрын

Yea, I like the layered better,,

@tammygraves5757 9 ай бұрын

Love the 3 dimensional one!! Thanks for the tutorial!!

@TheClackShack 9 ай бұрын

Yea, I think it is a keeper…thanks for watching

@darrellrichards2133 7 ай бұрын

Layered

@TheClackShack 7 ай бұрын

yes

@craftingwithjean5599 9 ай бұрын

Very nice Lightburn tutorial. I enjoyed seeing how you made the file. Prefer the 3mm layered.

@TheClackShack 9 ай бұрын

Glad you liked it…

@michaelameredith 8 ай бұрын

I wonder how it would look with the layered door with some of the engraved lines, like around the windows and the 45s on the frame corners.

@TheClackShack 8 ай бұрын

Lots of options and added decorations possible.

@chrisgallaher3899 9 ай бұрын

I like the multi layer but with fill on bottom panels from single layer

@TheClackShack 9 ай бұрын

Cool idea,,

@chrisgallaher3899 9 ай бұрын

@@TheClackShack I wonder if it'll pass the Brandy test ?

@budgetmerch 9 ай бұрын

Nice - liking the 3D version, but I think I would experiment with the edges to see if I could get some more shape into them. Not keen on seeing flat edges where I think it would be better with more of a rounded over look. But other than that I see some procedures here that I want to explore. Lightburn keeps on surprising me with its capabilities, that's for sure.

@TheClackShack 9 ай бұрын

Rounded edges is hard to accomplish with a laser. A cnc, yea.

@budgetmerch 9 ай бұрын

@@TheClackShack I suppose it would involve lots of individual power settings to get the depth of cut but I'm guessing.