@ronalddavis Жыл бұрын
deer in the background
@pinohatoum3623 2 жыл бұрын
Thank you very much man you save me a few hundred bucks now because I have a nicked one of the barrel inside for inches and I learned quite a bit from you thanks again I love it
@infobros 2 жыл бұрын
I learned something and enjoyed it too! Hope you're feeling better Six.
@davidstuck2866 Жыл бұрын
yes, I did learn something. now I know how to make a lead lap. Thank You!
@cw2a 2 жыл бұрын
Evening man!! Blessings for fast healing man!! 🙏♥️🙏♥️🙏♥️
@HobbiesHobo 2 жыл бұрын
Good day SST. Thanks for showing us this. C19 be gone soon hopefully. Mike.
@johngarrie2633 7 ай бұрын
Thinks for the info now I know how to do it 👍🏻 . It will make them shoot better for sure !!! Will try it on my barrels .
@jh5869 2 жыл бұрын
I could see a difference. If nothing else the barrel is shining on the inside and that’s got to be slicker. Thanks 6 Shooter.
@wannabemgtow2540 2 жыл бұрын
I did learn something much appreciate it. I went through covet myself and I hope the best for you, for me it was a rough ride coming and going.
@accuracyfreaks442 Жыл бұрын
Thanks for the info! I enjoyed it.
@sureshotandrew 4 ай бұрын
Awesome.. thanks for your time to make this very important video.
@ocean374 2 жыл бұрын
That’s pretty cool thanks for sharing feel better my friend
@expressogino3971 3 ай бұрын
2 questions: 1) Do you have to coat the barrel to prevent the lead from sticking to the inside of the barrel, if so what to use? 2) Is that a deer at the 12 minute mark in the background? Thanks.
@sixshootertexan 3 ай бұрын
No you do not coat the barrel. Yes that was a yard deer.
@ewetho 2 жыл бұрын
Get better soon SST I just got over my second bout too
@mckwilly 2 жыл бұрын
good info, busy is good, keep on keepin on 👍
@jamespollard1670 2 жыл бұрын
Thanks for showing .
@Rooftroop Жыл бұрын
Heard you say you also do this on air rifles. I am curious because I want to try this in a small .20 caliber rifle. But the lead when pouring solidifies before it will run in the barrel. And it’s frustrating me on how to get it to go into the barrel.
@sixshootertexan Жыл бұрын
Warm the barrel up some but not hot. Get the lead temperature up some more. If you're only around 650 degrees, it will solidify too quickly.
@jonenglish6617 Жыл бұрын
Sorry you got Covid. I got a weak strain. But some folks had it bad
@nickspistolsfl9736 Жыл бұрын
what is this procedure for? to clean the barrel from lead deposits? Very strange. Dilute hydrogen peroxide and vinegar 50/50 pour into the barrel. then clean with a brush. repeat the procedure several times. lead oxide can be black yellow and red. Depends on composition
@sixshootertexan Жыл бұрын
Polishing the imperfections out. This can help in the prevention of leading. Makes general cleaning a lot easier. It also will help improve accuracy. High-end high dollar barrels are polished at the factory.
@williamfisher2906 6 ай бұрын
So... Lead is softer than steel , right? Has it occurred to you that you're lapping the lead plug and using the barrel to do so?
@sixshootertexan 5 ай бұрын
It's called sacrificial. You don't want the lap to be harder than the barrel. If the lead lap wears out before you accomplish your desired results, just make another. Plus, try to pour molded steel into your barrel to make a lap.
@gunnwild1 2 жыл бұрын
I've never heard of lapping a barrel, I know about lapping scope rings, but not a barrel
@Roy-tp2iy 8 ай бұрын
Comet,babbo,glem toothpaste.
@T.A.B.Videos 2 жыл бұрын
Thanhs for sharing
@dennistennyson8856 Жыл бұрын
You must be afraid to get your finger a little dirty huh ?
@sixshootertexan Жыл бұрын
No sir just trying to keep it from getting it all over the barrel and cleaning rod. It will dull a blue finish fast. Thanks for watching.
@jonleone777 3 ай бұрын
Once the lap is made it should never come out of the barrel untill your done lapping. Push it out just far enough to add compound. Also if you heat the barrel with a heat gun the lap will form better.
O’Neill Outdoors
Рет қаралды 13 М.