Great break down. These videos are great. // Overall Review -- In-depth look at Leaperkim Lynx, focusing on build quality and improvements. -- Noted for simple, straightforward design, easy to assemble and maintain. // Parts and Features -- Includes motor, suspension rod mount, Kender tire, two battery packs, rear stand handle and rod, power supply (150-12 volt, 5 amp). -- Battery side panels are easy to install; control bar has a straightforward design. -- Features U-shaped suspension bracket and robust motor setup. -- Bright lights and speaker included; concerns about light bracket durability under impact. // Tear Down and Inspection -- Control unit at top sealed with silicon, simple internal layout. -- Improved cable management for battery pack, ensuring snug fit and reduced damage risk. -- Chassis design is thin but strong, focused on weight reduction; handle is chunky but sturdy with some flex. -- Charging port at back with protective cover against water splash. // Performance Testing -- Free spin speed of 65 mph in normal mode, 82 mph in high-speed mode. // Final Thoughts -- Well-built with thoughtful design elements; minor concerns about part strength under high impact. -- Design simplicity aids in easy assembly and maintenance. -- Use of insulation tape on certain parts recommended for safety.

"Simple machine to put together or build" is music to my ears!

Best lynx quality video. Great suggestions too. Definitely going to run through mine when it arrives and do the same. Thank you.

Absolutely love how the quality appears to be improving

Thanks Kevin, and happy holidays…

Great video! Will follow your tips when mine comes

My god, that thing is beautifully made, looks easy to work on too.... think I'm in love, but punching above my weight (and bank balance).

Expert analysis .... everything is in order and the gloves are on 😀

great inspection as allways Kevin and Erides are top.

Indeed, very informative 👌 Thanks

Great video

A desirable machine. ❤

I like that black rim

this is asmr for me

v14 building quality check video coming soon?

Thx👌🏼

👍👍👍

The bottom suspension bracket, what did you torque those bolts at?

Great video, I was curious about the products you’re using on bolts as you assemble the wheel. Do you discuss them in a prior video? I figure that medium thread locker is being used for most bolts, but what are you putting on the tightened bracket bolts after they are tightened?

Might it be worth gently warming the fuse holder housing, which may prevent it from cracking? Plastic gets brittle when it is cold too, of course. We hope to learn from your m… experience 😊

What torque did you set your torque wrench to when you were tightening those bolts?

. I hated my inmotion V11 because it's was hell replacing the tire or just pumping the shocks because of the pressure leaks. I hopethey lower the price a little in a few month for the Lynx

What is the water resistance in your opinion, how would you compare it to Inmotion wheels?

@23:25 Nice shoes 😁

Hello, what tightening torque do you use to tighten the suspension mounting brackets, for the motor it is 20Nm but how much for the small brackets? Greetings and thank you for this interesting video.

What bolts are you putting locktite on

On the bottom stanchion tubes, after you locktite the 6 bolts you put something from a tube on the head of each bolt. What is it??

Will ewheels take care of this for me or do I actually have to take apart my brand new wheel as soon as I get it ????

Way to small screws for a suspension . For motor looks ok .

17:19 what product do you use? the reference ? Thx

{tl;dr. I'm hard pressed to criticize the LYNX. So far, sooo good!.} I suspect that the controller base casting is Cast Magnesium (hopefully an Yttrium alloy). Stronger and lighter than aluminum, and without the self-sustaining burn characteristic that was typical of prior Mg alloys. If so, those holes appear adequate if not directly shock-loaded in a tumble. If it's aluminum, then I'd prefer that this casing be CNCed from a block of T6 AL with thicker ribbing and torsional gussets. It will be interesting to see how and where this casting fails over time. I wonder how much the replacement part costs because it's not really weldable, except by an extremely proficient shop? What's the fork crown material? Of course, the fantasy would be carbon fiber or EDM these parts from titanium; that would be worth double (to me), as I'd only have to buy an occasional controller and axial flux motor upgrade to keep it running competitively for decades... or, until electronic linear motor suspensions become viable (at which time it becomes reasonable to upgrade the entire unit. Now, LeaperKim needs a 14" version to capture the new rider, youth and elderly markets. Capturing disillusioned e-scooter riders is also ripe for adoption.

Does the Lynx have speakers for music?

Loctite on the screws?

Toujours le même problème avec le garde boue .. une galère après pour nettoyer ça machine ..