Lectric e-Bike Flat Tire Repair | E-Bike Tire Removal, Repair, Slime and Tire Installation!

No video

Lectric e-Bike Flat Tire Repair | E-Bike Tire Removal, Repair, Slime and Tire Installation!

Рет қаралды 64,905

2 жыл бұрын

In this video Dan performs a Lectric e-Bike Flat Tire Repair on his Lectric XP 2.0. We discovered a slow leak in the rear tire and this video goes over the removal of the rear tire, the repair of the innertube, the replacement of the rear tire, filling the tires with Slime, and a bonus tip at the end. If you're going to need to do a Lectric e-Bike Flat Tire Repair, this is the video to walk you step-by-step!
This is a long video but here are some timestamps to help:
Removal of Rear Tire: 3:56
Using the Water Test to Find Leak: 14:43
Repairing the Innertube: 16:00
Reinstalling the Rear Tire: 29:10
Front Tire Removal: 38:27
Bonus Tip: 44:54
Resources:
VIAIR 450P-RV Portable Compressor Kit: amzn.to/3u0AtMn
Slime 10003 Bike Tube Puncture Repair Sealant: amzn.to/38oHIW7
Slime Tire Tackle 33 pc kit (Part 20482) from Walmart: NOT available everywhere
Welcome to our channel! We are Dan and Kevin, two retired Air Force veterans. We hope to entertain and inform you of our life on the road as full-time RV'ers. We currently travel with our Siberian Husky Avalanche "AVA" Rose (1 yr) AKA "Roadie"!
Please consider hitting the Like and Subscribe button. Don’t forget to ring that Bell icon and select “all” so you can be notified when we release a new video. We really appreciate it as it helps us grow our channel and bring you more content.
*****************************************************************************
Our Inception:
We downsized from a three bedroom house in November 2017 to a 2000 Fleetwood Southwind Class A. We dubbed her Southwind Sally. We did some minor renovations with paint and adding new window treatments. In December 2018 we purchased our fifth wheel. It is a 2014 Forest River Columbus 320 RS by Palomino. In February 2020 we hit the road before the COVID-19 Pandemic lockdowns started.
Those lockdowns forced us to hold up at the Tinker, AFB FamCamp in Oklahoma until May. We hit the road again traveling to Arkansas, Missouri, Illinois, Indiana (where we had floor work done on the Columbus), Ohio and Michigan. We decided we were going to try and make it to Colorado to see the sights, and made our way there. This is when we decided to create our channel.
We have been watching our favorite KZfaq channels for years and decided maybe we should start to capture our own adventures. That decision produced our channel Compass Roadz and our first video.
For more information, check out these resources:
You can also find and contact us at:
Follow us on Facebook at / compass-road. .
Follow us on Instagram at / compassroadz
Follow us on Twitter @CompassRoadz
**************************************************************************
Music from Epidemic Sound (www.epidemicsound.com/referral...)
Intro/Outro music: “Even If the Sky is Falling Down” by Candelion
Background music:
Disclaimer: Any links may or may not be affiliate or referral links where the merchant may provide a small compensation to us at no extra cost to you. By using our links, you may be supporting our channel and of course, we really appreciate that.

Пікірлер: 262

@BR-br3pv 2 жыл бұрын

I had a puncture in my rear tyre but instead of taking the whole rear assembly out I just ran a spoon around one side the tyre, then I pulled out the tube inflated and found the leak, repaired this, checked the inside of the tyre for nails etc, replaced the tube refitted the tyre, bingo all done in 15 mins

@CompassRoadz 2 жыл бұрын

That is a great idea. Definitely a time saver. Thanks for watching!!

@chrisbamborough222 Жыл бұрын

Yes exactly I agree I have done that on flats ie Punctures for 50 yes . Just lie the bike down on the grass do as you have mentioned easy. No turning bikes upside down no removing anything only the tyre.

@RandomMotoThings Жыл бұрын

I’m not understanding how you are able to get the inter tube out completely and away from the bike if the wheel is still attached. How do you get it away from the wheel if everything is still connected? Everything is still connected in the center so how do you get any side of the inner tube out of it?

@BR-br3pv Жыл бұрын

@@RandomMotoThings You cant get it out but you inflate the tube and find the puncture and repair it?

@CompassRoadz Жыл бұрын

You wouldn’t remove the inner tube in that case, but you will be able to access the tube to repair it from the side.

@timrossmultimedia 4 ай бұрын

I'm a 70 year old new XP 3.0 owner... I'll never grow up. Excellent "real time" video presentation. Great info and enjoyed your presentation style, Thanks so much for sharing your time and expertise... very helpful! My best.

@CompassRoadz 4 ай бұрын

Thank you for the kind words. I enjoyed making that video. Hope you enjoy your 3.0! Thanks for watching!

@TexasHighDef Жыл бұрын

For a simple flat that you can see what gave it to you. All you need to do use the tire irons to take the tire off the bead on one side and pull that part of the tube out and fix it. Then just push it back in and fill it up. I ride sweep on a lot of group rides and have done to many time to remember. 99.9% of the time there is no need to remove the tire to fix a flat.

@CompassRoadz Жыл бұрын

That’s definitely a tip most of our viewers will appreciate. Thank you and thanks for watching!

@garythomas4981 Жыл бұрын

I like the rear tire flat information what I did not notice is you check the inner tube for leaks really well but before you put the inner tube inside the tire I was told you should reach inside the the tire and run your hand around there to make sure there's no little pieces of metal or needle pieces still in the tire you didn't see from the outside. Nice job I enjoyed the video.

@CompassRoadz Жыл бұрын

Definitely will take that information for next time (should there me a next time). We were fulltime rv’ers then and tools were limited. That being said it does make good sense to make sure the tire is clear of debris. As for the inner tube the gist of what to do was there, but I should’ve reshot that part or edited some words over the film. We aren’t professionals, but try to help. Thank you for your comment and thanks for watching. I may still go back and edit this video. I’ll do better in future videos.

@ggebhard1 Жыл бұрын

Compass Roadz This is my first video of yours and I give you a lot of credit for starting out admitting that this was your first, flat tire repair. I appreciate that! For the so call Master Mechanics who left negative comments, I can’t believe if they were so smart, then why watched your video at all! Since they did, they must have needed some kind of help. I’m going to subscribe, because I like honest people who want to help others! And I thank the people who gave you suggestions and offered some good advice! Keep up the good work!

@CompassRoadz Жыл бұрын

Thanks for the kind words. We definitely appreciate the comments from others that share tips we may not have heard or thought of. Being transparent about us being novices we think is relevant because if we can do it, I am sure almost anyone can. Thanks for watching and subscribing!

@koreangamer6142 Жыл бұрын

Thank you so much. I had 2 flat tyres in last 10 day front and rear. I couldn't figure out how to remove rear wheel. Now I am going to put truckers cargo straps between tube and tyre that I saw from other KZfaqr. It looks like adding extra super durable layer under the tyre. I hope this work for my bike

@CompassRoadz Жыл бұрын

You’re welcome. Hopefully the video helps and makes any future tire leaks easier to fix. Thanks for watching!

@stuartmaeshiro2254 4 ай бұрын

Thank you for taking the mystery out of changing the back tire. I really appreciate your help!!!

@CompassRoadz 4 ай бұрын

Of course the back tire is the hardest one to fix. I hope my future punctures are in the front if I do have to have one. Thanks for watching!!

@georgegorham1538 2 жыл бұрын

Thanks for the video! Very easy to follow your step-by-step instructions.

@CompassRoadz 2 жыл бұрын

You’re welcome and thanks for watching.

@rahinyajones651 Жыл бұрын

Thank you for the step-by-step. My first ebike and my first flat. Changed it by myself on the kitchen floor. Didn’t have to take the rear wheel off. Troubleshooted the problem and patched several holes. If I have to remove the rear wheel, I won’t be intimidated thanks to your video👱🏽‍♀️

@CompassRoadz Жыл бұрын

Awesome to hear. Now that you’ve actually had to do it, even if it was the front tire, you at least know you’ve got the ability to tackle the rear. Thanks for watching!

@MrFifth-up9jz 2 жыл бұрын

Great demonstration! Thank you for the step by step

@CompassRoadz 2 жыл бұрын

Thanks for watching! We’re glad it helped.

@christinebourke7620 Жыл бұрын

As a 68 yr old woman -who has no idea how to change the flat tire on me Veleco e-bike- this saved my sanity.Thank you! :-]

@CompassRoadz Жыл бұрын

Glad we could help. Let us know if you have any problems. Thanks for watching!

@tomkinsey1675 6 ай бұрын

I'm glad you made the video and didn't try to edit any of your mistakes because we all have a first time at everything yes we could criticize you but it was very informational. Thanks

@CompassRoadz 5 ай бұрын

I appreciate your support and hope it helps in some way. Thanks for watching!

@miketaube4868 2 жыл бұрын

Very informative! I'm glad I watched it.

@CompassRoadz 2 жыл бұрын

Thank you. I know it’s a very long video but I wanted to give a comprehensive step-by-step for either tire, how to repair a hole, and also putting in slime. I did put a time stamp in the description in case anyone wanted to just jump to what they need. Thanks for watching!!

@wynnbeattie8130 2 жыл бұрын

Great video. I added Mr Tuffy armor liners inside the tire before putting the tube back in to hopefully prevent further punctures.

@CompassRoadz 2 жыл бұрын

We’ll have to check into those. That’s the first I’ve heard of them. Thanks for sharing and thanks for watching!

@douglashunt7057 2 жыл бұрын

Appreciate your KZfaq info video. Excellent and informative and easy to follow. My father was a machinist for U P railroad for 30 years and he taught me a valuable lesson about adjustable wrenches. Always pull on the solid jaw of the wrench, not the adjusting jaw. The adjusting jaw might slip and you can strip the nut. Just something that might help everyone. But, I love your video. Thanks

@CompassRoadz 2 жыл бұрын

Wow, that is a good tip to know. I never knew that but will definitely use it. Thanks for watching!

@carynspohn9891 Жыл бұрын

Thank you so much for recording this.

@CompassRoadz Жыл бұрын

You’re welcome. We hope it comes in handy. Thanks for watching!

@Jim-xz1ew 2 жыл бұрын

We have the XP 2.0. Both my wife and I. We take our RV up to the Texas hill country a few times a year. My wife for some unknown reason can get a flat every time we ride. Mostly I think it is from cactus along our trails. I been luck. Had to change out the tire twice and yes it was the rear both times. We carry spare inter tubes and a small tool bag with pump. So the first thing I did was add the slime when we came home. So far so good. The XP wasn't too bad removing the rear tires as I thought it would be. I mean on the trail. My 16 year old daughter also rides the XP and has become pretty good on trails. Here in Houston Ebike theft has become a fad.And they are very good and fast even if your bike is locked and chained. We added Apple trackers inside our seats just in case. Things you need to do now days.

@CompassRoadz 2 жыл бұрын

Those apple trackers will become handy. Yep, eBike thefts are in the rise but we can only do so much. Importantly, just be safe. No eBike is worth you or your wife’s life if it comes to that. Thanks for watching!

@meghansweeney7468 Жыл бұрын

Thank you so much for this video! This is exactly what I'm going to have to do in the next few days on my bike ^_^ very thankful for the step by step video with the slime installation 🥰 thank you thank you thank you!!!!!!!!

@CompassRoadz Жыл бұрын

You are most certainly welcome. Glad it helps out and thank you for watching!

@imRosco69 3 ай бұрын

We have 2 e-bikes and had been riding them for the last 7 years. Flat Out tire sealant has worked 100% better for us than Slime. I used Slime for a few years and still got leaks. Never ever had a lead with Flat Out sealant. Nice work on changed the rear tire. It's a real pain to pull the wheel off the rear. I just deflate, pull the tube out, fix or replace and back in business in under 20 minutes. Great video.

@CompassRoadz 3 ай бұрын

Thanks for that information. We definitely heard about Flat Out after we posted this video. Although we already used slime in our tires, we will try Flat Out from here on in. Thanks for watching!

@Laogai001 2 ай бұрын

It’s a nice experience to know how to change your own tube know how to use the tools and everything

@CompassRoadz 2 ай бұрын

@Laogai001 it can save time and money 💰. Thanks for watching!

@ralphs007 Жыл бұрын

Thanks for taking the time to make this video. I think if I ever get a flat in the rear tire, I'm selling my bike.😂😂😂

@CompassRoadz Жыл бұрын

If you do get a flat in the rear tire, I’m sure you can fix it easily enough. Just give yourself 2 hours and have all your tools and go one step at a time. You’ll probably finish within 30 minutes but if you allow yourself 2 hours then it will give you a confidence boost that you did it in quarter the amount of time. Lol. Thanks for watching!

@goodcitizen4587 7 ай бұрын

Thanks for the vid! Looks like 'Flat-out' is even better than Slime.

@CompassRoadz 7 ай бұрын

I haven’t tried Flat Out yet but will next time. Thanks for watching!

@sgarcata Жыл бұрын

When I have to fix a flat, I'm going to insert Mr.Tuffy tire liner to protect against the myriad thorns prevalent here in the AZ desert. Thanks for this video. It's been nearly 50 years since I fixed a tire and I was (and still am) nervous about getting that back tire out. Or even turning the bike over. I'm 81 and not the strongest chick on the block. I am surprised that the liquid slime didn't patch up that tiny hole or maybe you didn't have it in your tire previously. Now Lectric is shipping out the bikes with slime already inserted.

@CompassRoadz Жыл бұрын

That’s a great idea. My parents lived in AZ and there are a lot of thorns. I hope I’m as limber to bike when I’m 81. Let us know if we can provide you anymore information. Thanks for watching!

@sgarcata Жыл бұрын

@@CompassRoadz Since writing the above, I found out about Flatout which seems to be able to seal a larger tear. First I had heard of it so I have no direct experience, but I've ordered some to keep with me. One of the dynamics I'm starting to realize is that eBikes are going to enable "regular" folks like myself to get much farther out even on some unpaved trails. As a result, we need to be prepared for handling issues like nasty flats on our own. So far there isn't a AAA for bike breakdowns; although I think it wouldn't be a bad idea especially here in AZ where the interest is exploding and where there are so many trails often quite away from a well-traveled road.

@jesseault5045 2 жыл бұрын

Just buy some flat out and install, won’t have to worry about a flat. I did it as a preventative maintenance on bike. Great product.

@CompassRoadz 2 жыл бұрын

We are going to try that next time. Thanks for watching!

@frankwesley9042 2 жыл бұрын

Good information on breaking down the wheel, but since it is a back wheel which is harder to get off I would put a new tube in. Don't have much faith in patches.

@CompassRoadz 2 жыл бұрын

That’s understandable about the back wheel. It’s been about a month since fixing that tube and about 40 miles with no issues. I’ll do a follow up if in the event the patch fails and give a total number of days in between. Thanks for watching Frank.

@jeffreynoreikas4764 2 жыл бұрын

Repair back tire

@timbuckingham6734 Жыл бұрын

Good demonstration. One thing I always do is run my finger over the inside of the tire to make sure I got all the possible things that can make a tube puncher out. When I was young I had to patch a new tube as I missed a tiny bit of glass. Wire can cause the same thing if a small bit breaks when pulling it out.

@CompassRoadz Жыл бұрын

That’s a great tip! Thanks for sharing that and thanks for watching!

@timbuckingham6734 Жыл бұрын

@@CompassRoadz oh ya if you think it's glass wear a glove well checking, save getting a cut

@CompassRoadz Жыл бұрын

Good point! Thanks

@gimpman1357 2 жыл бұрын

I saved this video for future reference. PS. I really love Jed the bonus tip.

@CompassRoadz 2 жыл бұрын

Thanks! Glad we could help and thanks for watching!!!

@wilburbowen7317 2 жыл бұрын

To avoid flats I put in tire shield liners. The tire liner is a thick plastic strip inserted between the tube and tire. What cool is you don't have to remove the tire to insert because these tires are very wide.

@CompassRoadz 2 жыл бұрын

That's a great idea. I also saw that using the old innertube (when sliced in half lengthwise) also works good. Thanks for watching!

@stevopusser9093 7 ай бұрын

I haven't found any liners for fat tires that don't cost the same or more than the tire itself! Maybe a few years down the line...I can get bargain ones for 26 x 2in tires for a few bucks.

@danielmedina333 Жыл бұрын

thank you for the video sir!

@CompassRoadz Жыл бұрын

You are very welcome and thank you for watching.

@far2manygadgets38 2 жыл бұрын

This was very helpful. Incidentally, the metric measure for torque is Newton-meters.

@CompassRoadz 2 жыл бұрын

Glad it helped! I’ve heard of Newton-meters before but I’ve always used foot-pounds I had forgotten what the metric term was. Now I’ll remember. Thanks for watching!

@rachael9372 4 ай бұрын

Great video

@CompassRoadz 4 ай бұрын

Thanks for watching!

@scootloot Жыл бұрын

Helpful video

@CompassRoadz Жыл бұрын

Thank you very much and thanks for watching!

@garywillhoit 2 жыл бұрын

Adding a little air in the tube makes it easier to handle when placing it back in the tire. You will have fewer problems with the tube being where it’s not supposed to be. 🚴🏻😎

@CompassRoadz 2 жыл бұрын

That’s a great idea! That will help me next time. Thanks for watching!

@raymondherbst7126 9 ай бұрын

Small puncture you can deflate the tire, pull the staple or nail and remove valve stem and put the slime in, replace valve stem, inflate and ride. Can work on front or rear. Done it with motorcycles and then rode 1000 miles no problem, no leak, no balance issues.

@CompassRoadz 9 ай бұрын

That absolutely works for small punctures. In fact, just using slime in the tires before a puncture also helps. Thanks for watching!

@stephendenagy3396 2 жыл бұрын

Nice, big job! Suggestion, if the rim can handle it, switch to a tubeless configuration. Easier repairs, generally self healing. The Slime treatment approaches the idea. I have 2,300 km and no flats on my Specialized.

@CompassRoadz 2 жыл бұрын

We never thought of that as an option. We were just sticking to the stock tire option. But will definitely consider that if we need to replace them. Thanks for watching!

@thefix-itguyreviewer8151 2 жыл бұрын

I'm pretty sure you can't have a tubeless option when you have spokes..

@wilburbowen372 Жыл бұрын

I inserted tire liners, Mr. Tuffy, to prevent flats along with orange seal which more effective than Slime because it is liquid latex.

@CompassRoadz Жыл бұрын

Yep, that’s a great way to recycle old tubes as well. Thanks for watching!

@mikerochester 2 жыл бұрын

Knowing where the hole was is it possible on that bike to repair the tube without removing the tire?

@CompassRoadz 2 жыл бұрын

It is possible, depending on where on the tire the hole is, you may have to remove the side of the tire to access the tube to repair if just using slime doesn't work. Thanks for watching!

@davidpattison5860 7 ай бұрын

Looks like it’s the first time you’ve ever repaired a puncture on a bicycle , I’ve never seen a tube and tyre fitted onto a wheel in this manner before , it looked like real hard work , but everyone has their own best way , I didn’t see the sprocket go through the chain before you put it all back together but the edit showed it all ok , would be nice to show novices what to do and how not to make mistakes , Happy cycling

@CompassRoadz 7 ай бұрын

I’ll try to remember to mention any action I may have taken during editing if there was something I left out next time. I thought I had restarted at the place I had ended. Thanks for watching!

@davidfarm8095 Жыл бұрын

Just got my bike today front tire did good. back tire has leak sounds like a big leak. may have to change tube want know til I take it apart.

@CompassRoadz Жыл бұрын

Is it brand new? Lectric should know if it was delivered with a bad tube.

@Laogai001 3 ай бұрын

Tire on the the wheel first then the inner tube make sure to position the valve on the hole and then the nut if there is no nut that’s okay just make sure the valve is thru the valve hole first and then insert the rest of the tube at least that’s what I always do. Enjoy ur e-bike their fun riding

@CompassRoadz 2 ай бұрын

Thanks for that great tip and thanks for watching!!

@rickhudson6890 2 жыл бұрын

Keep putting out good content!!

@CompassRoadz 2 жыл бұрын

Thanks. This one was long but in-depth.

@georgecambian6170 Жыл бұрын

You do realize that you didn’t have to take the wheel off to fix this flat and save about 15 minutes of video. You got it fixed though. I give you credit for that. 👍

@CompassRoadz Жыл бұрын

Yes, for the little leak and location we had this time, I could have done it easier without tire removal. But, since I was trying to make an all-inclusive video I thought I’d tackle it, espy the rear tire. Thanks for watching!

@synchemist6462 2 ай бұрын

I had a rapid leak. It was flat within a minute of filling it. I removed the valve stem and put 8 oz Flat Out in tube, filled it with air and it has held without losing pressure for over a month so far.

@flynlow4ever 2 жыл бұрын

It’s funny that I was just researching tire protection earlier and now your video! I’ve read Flatout might be better than Slime. Still researching Tannus vs other liners. They seem pretty good while being rather expensive. I suppose it comes down to how much your willing to spend to deter a flat tire.

@CompassRoadz 2 жыл бұрын

I haven’t tried Flatout, nor even seen it, but I’ll take a look at that to see how it compares to Slime. Although, I try to go the most frugal route where I can as long as it has good value. Thanks for watching!!

@flynlow4ever 2 жыл бұрын

Frugal? LOL!!! I carry a tire patch kit!

@CompassRoadz 2 жыл бұрын

Always best to have that, just in case. I may be getting a spare inner tube too!

@wilburbowen7317 2 жыл бұрын

Yoga blocks work great to rest the handlebar so as not damage the control screen.

@CompassRoadz 2 жыл бұрын

That is a great idea. They are small and lightweight for travel too. But maybe you haven’t watched enough of our videos. There is nothing about our rotundness that screams we do yoga! Lol. 😂😂😂 Thanks for watching!

@Human-Earth 2 жыл бұрын

Thank you for this valuable info and so useful practical demonstration about flat tire. I’m shopping for e-bike and love to have Lectric XP 2.0 E -Bike,but unfortunately some people complain about the controller get burn out after just couple hundreds of miles! What’s your opinion about this matter ? And thank you so much for your great videos 🙏

@CompassRoadz 2 жыл бұрын

Fortunately we haven't had any problems with the controller yet. If that is a frequent problem, I would have to see how Lectric responds to customers that have that issue and how/if they correct it for them. Sorry, I don't have a very good answer for you but you can bet that if we do have an issue with it, we will document it and put out another video and let people know how they can resolve the issue. Thanks for watching!

@Human-Earth 2 жыл бұрын

@@CompassRoadz Thank so much for responding, Great that you guys have no issue,and I’m sure Lectric always has a good respond and great customer service. 🙏☘️🙏

@Alcoholpad Жыл бұрын

Awesome video I’ll probably have to watch it 10 more times before I attempt to remove mine. I’m so nervous that I won’t put something back the way it was. I’m thinking about buying a new tire and tube just to be safe because I’m not sure how I got a flat in the first place 😅

@CompassRoadz Жыл бұрын

Which tire has the flat?

@Alcoholpad Жыл бұрын

@@CompassRoadz my rear, I found a local bike shop that will do it for me he’s also saying he can add tannus tire armor for $220. I’m considering

@bernardchalecki4163 Жыл бұрын

Take pictures with your phone during disassembly, refer to the pics during reassembly

@Alcoholpad Жыл бұрын

@@bernardchalecki4163 I’m a professional now I ended up replacing myself know how to disassemble/reassemble because of this video. Thanks for the suggestion though I will definitely use this technique for future repairs

@CompassRoadz Жыл бұрын

Glad to hear it worked for you. Next time will be so much easier for you!

@harrylaber6227 Жыл бұрын

I put baby powder in the tire before installing the tube. Makes the tube expand easier when inflating without any pinching. Also I use tire Armour.

@CompassRoadz Жыл бұрын

Those are both great tips! I’ll be sure to try both next time. Thanks for watching!

@carynspohn9891 Жыл бұрын

Are there any coupons or discounts in buying an electric bike? I'm in the process of choosing this brand or a Ranger Heybike.

@CompassRoadz Жыл бұрын

Lectric has an early Black Friday sale going on. Their site is lectricebikes.com/. They are promoting the new XP 3.0 but they also have a sale on the older 2.0 which we have.

@markwitte303 11 ай бұрын

for a moment i thought you were going to say a metric adjustable wrench on the tools list.😀

@johnstack5008 11 ай бұрын

Your rear wheel spins freely. Mine spins about 3 turns and stops unlike the front that spins freely. It also makes a light rubbing noise while spinning. It's not brake rubbing because it does the same with the caliper removed. It's been like this since new. I thought it was normal. I'm going to contact Lectric. Thanks for the video.

@CompassRoadz 9 ай бұрын

Sorry this is late, but were you able to find out from Lectric? Thanks for watching!

@johnstack5008 9 ай бұрын

Never did figure it out. Shortly after posted that, my bike got a controller failure and controllers were back ordered. Lectric decided to give me a brand new bike rather than make me wait for the controller. A great deal for me because my bike had over 2000 miles. Service is top notch over there. I did speak to a mechanic friend about rear wheel. He said if there is no brake rubbing then most likely it's an overtightened cone nut which is an easy fix.

@robertwalker4099 2 жыл бұрын

Just Curious, What is your advice about Using "FlatOut" or "Slime" Tire Sealant on my Bike Tires to hopefully prevent a Flat Tire, before it happens and hopefully Avoid having to go thru the timely process of Removing the Wheels?

@CompassRoadz 2 жыл бұрын

Actually, in the email I got from Lectric, they actually recommended using Slime as a preventative measure to be used in their tires. Although they didn’t mention “FlatOut” by name, I’m sure it could work as well. Thanks for watching!

@robertwalker4099 2 жыл бұрын

@@CompassRoadz Yes, I too have read that Lectric Uses or recommends SLIME, although from what my research has found, "FlatOut" is rated as having a much higher Longevity in your Tire. I Recommend to do your research on "FlatOut" and let me know your thoughts concerning "SLIME" vs. "FLATOUT". I bought a Bottle of "FLATOUT" and will be installing it very Soon, as soon as our Michigan weather gets a bit Warmer. I am 71 and Fixing a Flat on the Trail is not an issue I ever want to deal with with my Lectric XP 2.0 Black Step-Thru E-Bike. Let Me Know too. Also ""THANK YOU" for your informative Video on Repairing a Flat Tire, a lot of Time & Effort for sure!!

@CompassRoadz 2 жыл бұрын

I will definitely check FlatOut the next time we need to put some me in a tire and compare it to Slime, although we’d have to get a puncture in one of them in the same terrain to prove one better than the other I guess. But we’ll see. We will let you know.

@stevopusser9093 7 ай бұрын

More expensive than Slime, but far better-working, are Flat-Out Sportsman or Muc Off (inner tube variant) leak sealants. With you finding and removing the wire, the procedure would have been then to remove the valve cores, add the sealant to the tubes, reinstall the cores, spin the wheels for a minute, then pump them back up. Done!

@CompassRoadz 5 ай бұрын

Thanks for sharing that information. It will definitely help us and others out. Thanks for watching!

@davesanders9203 8 ай бұрын

All good "old school" method. In this century it's only necessary to remove enough of the tube "at the right place" to patch a tire. CAREFULLY put the tube back in so no kinks.

@CompassRoadz 8 ай бұрын

Yes, they may be rubber but still delicate enough to get a rip or hole if pinched. Thanks for watching!

@Comewithmeifuwant2live Жыл бұрын

When putting the wheel on, the side where the gears/and connection are won't sit down into the frame all the way. It's close but it's a fraction off the mark. All good on the other side. Hesitating about hammering it though. Tried a bit of force but no good. Any ideas?

@CompassRoadz Жыл бұрын

I think I had the same problem. I did use a rubber mallet or a hammer just to tap it in gently. Hope that helps. Thanks for watching!

@Comewithmeifuwant2live Жыл бұрын

@@CompassRoadz I'll give it a go. I've send a video to the shop so waiting to hear back from them and then I'll use some brute force 😂Thanks!

@CompassRoadz Жыл бұрын

@@Comewithmeifuwant2live Not brute force. Just little taps. Good luck!

@patrick6437 Жыл бұрын

Very informative. Thanks

@CompassRoadz Жыл бұрын

Thanks! Glad you liked it. Thank you for watching!!!

@allandavies1187 Жыл бұрын

Hi! Can we use Slime & Flat out together???

@CompassRoadz 9 ай бұрын

I honestly don’t know if you can. Did you try?

@BobbyParker784 8 ай бұрын

I've got an Fucare Fat Tire E-Bike that I've somehow set a 4 diggit passcode on and I can't unlock it ! tried all kinds of FYI's. No body is showing type of situation 😢please help me! 🙏 you seem to be the most knowledgeable on here and the easiest to understand

@CompassRoadz 8 ай бұрын

What/where is the passcode put on? I’m not familiar with that brand but I can do some research on it. Does it use a passcode instead of a physical key?

@CompassRoadz 8 ай бұрын

Which model do you have?

@BobbyParker784 7 ай бұрын

@@CompassRoadz is the Gemini series and somebody sent me a passcode and it worked 1313 Factory code was 1212 that didn't work apparently I had bypass that and I was just trying to figure out the controls and inadvertently had put a code in there but I got it fixed I appreciate you thank you

@davidgambler1591 2 ай бұрын

None of those tools are required ! 😁 Leave the tire on, remove the all the air, break the bead, pull the tube out at the puncture point, sand the puncture point, apply glue, waiting 1 min. then apply patch. Add air, all done.😊

@CompassRoadz 2 ай бұрын

True. That is another way, and easier way if it is a simple pin hole in the tube. Thanks for watching!

@thefix-itguyreviewer8151 2 жыл бұрын

Don't understand why you took out the brake caliper. I've seen people take these tires off many times without taking the brake caliper off at all. It just slips out..

@CompassRoadz 2 жыл бұрын

I only took it out because Lectric put that in their instructions. I probably could’ve avoided that step if it was loose enough to remove. But in making the video I just wanted to give Lectric”s instructions so as not to confuse anybody. Thanks for watching!

@thefix-itguyreviewer8151 2 жыл бұрын

@@CompassRoadz oh okay now it makes sense got it!! Loved your video by the way!!

@CompassRoadz 2 жыл бұрын

Thanks. Hope you enjoy your eBike!

@AH-st1my 7 ай бұрын

Try Tannus Armour, my friend. It's a bit pricy, but we'll be worth it. In my experience Slime is junk. If have to go that route us Flatout. It seems more fibrous.

@CompassRoadz 5 ай бұрын

Thanks for sharing that product. I’ve never heard of that but will look for it next time. Thanks for watching!

@HadenPrell Жыл бұрын

I was doing great following along until you unplugged your motor and when I looked in the same spot there wasn't a plug and I realized you're working on a 2.0 and I'm working on a 3.0. Now I'm confused and trying to figure out how to unplug that 😅

@CompassRoadz Жыл бұрын

We have not yet seen a 3.0 so that would be a whole different monster to us. Hopefully you were able to figure yours out or maybe there was a KZfaq video for the 3.0. The manual online may be of help and they do have great customer support if you need. Let us know how it goes/went. Thanks for watching!

@mikeskee Жыл бұрын

hint; when reinstalling the inner tube and tire to the rim, put the valve stem in first through the hole in the rim, and put the valve stem cap on it , then install the rest of the tube and tire.

@CompassRoadz Жыл бұрын

Thanks for the tip. That definitely will make it easier. Thanks for watching!

@raymondherbst7126 9 ай бұрын

Oops, forgot to lace the chain around the hub first time didn’t ya? Been there done that!

@Thomas-yr9ln 7 ай бұрын

Ebike companies need to invent the spare tire for the ebike.

@RichardDow-djmrswotchnonstop Жыл бұрын

There are not enough bike shops in long island ny and they should start making house calls. Lol

@CompassRoadz Жыл бұрын

A mobile bike repair van sounds like a great idea! Might be a great opportunity for someone. Thanks for watching!

@ralphw8833 4 ай бұрын

At 30:08 the derailleur on the drive side was not put back on chain...then went to other side to put retaining nut on non-driveside axle... WHEN WAS THE CHAIN PUT BACK ON LOVE CASSETTE ? NEXT...he moves back to DRIVE side and the chain is back on the cassette... Mysteriously...then a minute later after he BEATS THE fastening nut with a HAMMER (never use a hammer on any bike part .or a screw driver on a tire needing removal.

@refresh77 Жыл бұрын

Do you know if Lectric started to put slime in their new bikes?

@CompassRoadz Жыл бұрын

No, I don’t. Did you hear that somewhere? Thanks for watching!

@refresh77 Жыл бұрын

@@CompassRoadz I read somewhere from Reddit.

@CompassRoadz Жыл бұрын

That’s interesting. Although I think Lectric would advertise that as a feature they provide over the competition.

@refresh77 Жыл бұрын

@@CompassRoadz I'll let you know when I receive my XP 3.0. How can I check if they filled the tires with slime? Do I need to deflate the tires completely or would I see some green stuff if I let the air out a little bit?

@CompassRoadz Жыл бұрын

@@refresh77 you won’t have to deflate the tires but you will have to inflate them. They come with little air in them for shipping reasons.

@FetchTheSled Жыл бұрын

I tried Slime in my atv tires. The little fibers would get stuck in the valve stem causing a slow leak. I don't think it's a good product.

@CompassRoadz Жыл бұрын

I have only used it on bike tires. I’m not sure if it’s recommended for other types. But, fibers getting caught in the valve stem and creating a slow leak is not good. If the tire tube No longer has a leak, I wonder if there’s a way to force those fibers into the tube and out of the stem valve. Maybe you can contact Slime customer service and see if they have a solution. Thanks for watching!

@scubatrucker6806 2 жыл бұрын

I little bit of dish soap and water in a sprayer bottle would work as well and get yourself a tire marker in your kit.

@CompassRoadz 2 жыл бұрын

I didn’t even know about tire markers! I definitely need to get one. Thanks for watching!

@johnfilmore7638 2 жыл бұрын

“tightening as hard as you can” is just stretching and deforming the screw threads, either the male or female threads will deform whichever is softest, hopefully the nut. Torque ratings keep your threads functional.

@Leo_Pard_A4 2 жыл бұрын

This

@ElderTechDragon Жыл бұрын

I've studied this tutorial carefully and I still can't figure out why he needed to remove the rear tire to add the Slime?

@CompassRoadz Жыл бұрын

Oh it’s not necessary to take the tire off to add the slime. I took the tire off to show where the metal wire went into the tire and inner tube so I could show how to patch a hole. Thanks for watching!

@hondamotorsrider 29 күн бұрын

If I’m taking the wheel off, I’m replacing the tube completely. I’ll use patches for trailside emergencies to get me back to the car

@Heritage57 7 ай бұрын

Next time you do this about the tire. Put a color green liner in the the tire against the tube so it won't get punctured.

@CompassRoadz 5 ай бұрын

Great idea. It will definitely make it stronger. Thanks for watching!

@franduce Жыл бұрын

Front tire bolts are size 15 mm

@CompassRoadz Жыл бұрын

Good catch. I stand corrected. Thanks for watching!

@franduce Жыл бұрын

@@CompassRoadz we are all learning as we go. At first I tried 18 and was unsuccessful and landed on 15👍

@CompassRoadz Жыл бұрын

Kevin said if it was 10mm we would’ve been SOL🤣. Thanks again for the right info and for watching. We are looking forward to more rides when the weather warms up.

@wynnbeattie8130 2 жыл бұрын

Just noticed, the tube is 20x4 and the tire is 20x3 ?. See 20:00 minutes

@MarkSmith-mj9mv Жыл бұрын

Pout tire on first one side on the tuby

@CompassRoadz Жыл бұрын

Good tip. Thanks for watching!

@raymondherbst7126 9 ай бұрын

Use kids bottle of bubbles and put over suspected area to find puncture.

@CompassRoadz 9 ай бұрын

That’s a great idea!

@MN_Doughboy 8 ай бұрын

Did you really bang on your axle shaft threads with a hammer? 😂😂😂

@axelthorfilms 8 ай бұрын

Slime severely throws the tire out of balance. Put Slime in and lift the tire off the ground and hit the throttle.. Being cold out don't help. It gets thick and does not flow well.

@CompassRoadz 8 ай бұрын

That’s good to know. I had no idea. Although, they do recommend you spin your tires after putting it in. That must be the only way to evenly distribute it. Probably good to drive it around awhile immediately after putting it in. Thanks for watching!

@ericoswood1856 Жыл бұрын

FYI, 40 newton meters equals 29.5 ft lbs

@CompassRoadz Жыл бұрын

Thanks for the info and for watching.

@karenohara9669 2 жыл бұрын

Omg so hard to do I have a electric nakto you 22 inch bike my front tire is flat I DK what imma doing bike shop is always good

@CompassRoadz 2 жыл бұрын

If you haven't taken it to a bike shop yet, the front tire is so easy to remove. Before removing it though, are you able to find a nail or something in the tire?

@karenohara9669 2 жыл бұрын

Thank you I'm pretty sure it has a nail in it I did see some something shinny in the tire thank you for your help

@CompassRoadz 2 жыл бұрын

@@karenohara9669 you should be able to take the front tire off easily at the center of the rim. Then remove the nail. You should easily be able to remove the tire from the rim and find the hole in the inner tube. Use a patch kit to seal the hole and then use half a bottle of Slime to put in the inner tube and put the tire back on over the inner tube and fill the tire to required pressure and put back on the bike. Should be easy for the front tire!

@MarkSmith-mj9mv Жыл бұрын

He didn't have the chain on at first

@CompassRoadz Жыл бұрын

Nope! But I ended up figuring that out. Thanks for watching!

@Thomas-yr9ln 7 ай бұрын

You need a yellow marker.

@CompassRoadz 7 ай бұрын

That would definitely be handy. Thanks for watching!

@marym777 Жыл бұрын

U should put tire on first then put tube in .

@CompassRoadz Жыл бұрын

I’ve been told that by someone as well. I will try that next time and see if it’s less cumbersome. Thanks for watching!

@LuGrainzy 10 ай бұрын

I think the rear tire was tightened way to tight.

@CompassRoadz 9 ай бұрын

I didn’t use the torque wrench for it but it’s working. It does/did get torqued correctly in our annual maintenance inspection we do. I may do a video on that in January. Thanks watching!

@iluv_uman Жыл бұрын

The front tire are 15mm nuts.

@CompassRoadz Жыл бұрын

Yep. I misspoke. Thanks for watching!

@iluv_uman Жыл бұрын

@@CompassRoadz Thank you for making the video.

@CompassRoadz Жыл бұрын

Thank you for watching and for the info on my mistake.

@danpayan9468 9 ай бұрын

That's a lot work I'd rather pay to have it done

@CompassRoadz 9 ай бұрын

The rear tire is more complex than the front. The Front is easier. It all depends on if you have someone that can do it for you or someone f you can’t wait for an appointment, at least you have the information and option to do it yourself. Thanks for watching!

@raymondherbst7126 9 ай бұрын

Nm and inch pounds or ft pounds are different. I hate converting.

@CompassRoadz 9 ай бұрын

I hate converting too.

@Dan-tl5zf 2 жыл бұрын

Jesus loves you so much ❤ 💓 💖 💗 💛 💕 ❤ 💓 💖 💗

@CompassRoadz 2 жыл бұрын

He loves us all with all our flaws and sins.

@uuzd4s 3 ай бұрын

Just Wrong on So many levels. The Chain was never wrapped around the cassette before he took a Hammer to the Axle, which is why the axle wasn't fully seated into the Dropouts. The correction Wasn't Shown ! It's obvious he'd not done this before which makes this a Gr8 lesson on haw NOT to change a Fat Bike Tire. Too many mistakes.

@user-qv8eo5iv5j 3 ай бұрын

ENYBODY wanna buy mine it's got a flat back tire you can play to the video with 😆

@GoofyAhhMods Жыл бұрын

My tire is leaking so much slime I think I had a blowout

@CompassRoadz 9 ай бұрын

You may have to replace the inner tube. Thanks for watching!

@GoofyAhhMods 8 ай бұрын

@@CompassRoadzoh yeah I've been over that one 2 times now 😂 I had my controller shit the bed on me 2 days ago I had to pedal 7 miles on uphill home felt dead after pedaling like that mind you I got smoker lungs

@williecolon9678 8 ай бұрын

Nice, hammer the threads. Not so nice🤪

@SmokeWithMeInCT Жыл бұрын

Soooo one bike they sent me had issues . They sent the replacement and 4 days in I’m changing the back tire aka motor and the throttle already! What’s with this damn company!

@CompassRoadz Жыл бұрын

Sorry you’re having a rough start. I can see how it takes all the fun out of having them. Thanks for watching!

@SmokeWithMeInCT Жыл бұрын

@@CompassRoadz I would say that is More than a rough start lol 😂

@CompassRoadz Жыл бұрын

But let us know if they do take care of you.

@SmokeWithMeInCT Жыл бұрын

@@CompassRoadz they been “ taking care “ of me but with no good results but quick to offer a free accessory that may or may not show up .I don’t want a free accesory, I want the bike to be the quality they say it is suppose to be . And don’t dare disrespect there subpar company they will just stop replying but sorry to say I have no idea how they have a high rating .. I already had to file a BBB complaint and that’s how I ended up with the 2nd and worse bike replacement . It’s ridiculous

@SmokeWithMeInCT Жыл бұрын

@@CompassRoadz great channel btw.

@robertbrooks7936 5 ай бұрын

Bad video!!! You put the tire on the bike wrong and you did not show them how to correct your mistake. Then you hit the threads on the rim with your hammer. You should never hit threads like that because it can ruin the threads and you may not be able to screw the screw back on. People will tear up there bike if they follow your directions. Sorry bro I know you tried, but you don’t know what you’re doing. To be honest with you, you never had to take the tire off in the first place. All you had to do was remove the staple and then add slim (I would use flat out) and air it up and ride the bike. 10 min and done.

@tmmoose470 2 жыл бұрын

Flat out works better than slime.

@CompassRoadz 2 жыл бұрын

We haven’t tried that yet but have received many good comments on it so we will try it on our next tires. Thanks for watching!

@Dan-tl5zf 2 жыл бұрын

Life is short

@CompassRoadz 2 жыл бұрын

Yes it is so enjoy the time you have. Thanks for watching.

@markwitte303 11 ай бұрын

spoke nipples are the reason for the tape.

@NormWilkins1 10 ай бұрын

Never use screwdrivers to remove a tire from the rim. Screwdrivers will tear the innertube. Use the proper tools for the job.

@CompassRoadz 9 ай бұрын

You’re right. I just had to make do at the time. Some inner tube repair kits come with plastic tools. Thanks for watching!

@johna.a.9829 9 ай бұрын

Holy s**t! Banging on a crescent wrench to loosen up an axle nut (yes, it's called an axle nut) instead of using the CORRECT wrench, stating you can use a SCREWDRIVER to remove a tire from a rim (it's called "snakebite" because that's what it does to your tube) instead of using tire irons, not removing the valve stem cap before you removed the tube, I'm sure there's more but I had to stop watching this - this is BARELY the correct way to repair or replace a punctured tube. I've worked on bicycles for over forty years., If you want to mark a tire - good idea - make the mark LARGE. It's a tire - who cares. I really am in shock watching a mechanic smacking a crescent wrench with a mallet. An 18mm wrench can be had for not a lot of money. That is an unacceptable way to loosen up ANY nut, let alone one that is securing your rear axle.

@FoundersFan Жыл бұрын

Seriously dude, if you are making a vid be aware of your camera angles. "As you can see..." was OFF camera. Couldn't see a thing.

@CompassRoadz Жыл бұрын

Sorry I missed the mark on that one. Hopefully you were able to understand it through context. Thanks for watching!

@DonKelleyOnline Жыл бұрын

The loud breathing is quiet distracting

@CompassRoadz Жыл бұрын

Sorry about that. It was hot that day and I was trying to get a lot done with the bike, tools, cameras etc. Although I may have failed you in the videography, hopefully I helped you out in the content. Thanks for watching!

@ralphs007 Жыл бұрын

That's what she said.🤣🤣🤣

@kevinpendleton5585 Жыл бұрын

Is it loud or is it quiet, because it isn’t quite clear from your comment!