Led tv Vgh, vgl Short removal on 50 inch innolux panel latest method and tricks.|Panel Repair.

Рет қаралды 73,528

3 жыл бұрын

Led tv Vgh, vgh Short removal on 50 inch innolux panel latest method and tricks.|Panel Repair.
#ElectroPixels
#vghvglbypass
#Nopicture
#panelbonding
#panelrepair
#servicetv
#ledtvrepair
#tvrepair
#Innolux
#displayproblem
#repair
#repairing
#tips
#electropixels
#panelshort
#vghshort
WARNING & DISCLAIMER: This project is for entertainment purposes ONLY! Anyone attempting to replicate anything seen in this video, do so entirely at their own risk! **I WILL NOT ** accept responsibility(ies) or liability(ies) for personal injury or death, caused to yourself or others, or for damage to, or loss of property, in any way, at any time. = YOU HAVE BEEN WARNED! = ========================================
This video is for educational purposes only. The results are not typical. There is no guarantee that you will Success in using the techniques and ideas mentioned in this video. Your level of success in attaining the results claimed in this video will require hard-work,experience, and knowledge. I am only sharing my biased opinion based on speculation technical skills and my personal experience. You should always understand that Repairing Electronic gadgets without technical Knowledge there is always a risk. You should do at own risk your before making any Repair's and Experiments.
Copyright Disclaimer Under Section 107 of the Copyright Act 1976 allowance is made for 'Fair Use' for purposes such as criticism, comment, news reporting, teaching, scholarship, and research, Fair use is a permitted by copyright statute that might otherwise be infringing, Non-profit, educational or personal use tips the balance in favor of fair use

Пікірлер: 79

@jahabarsadiq3227 3 жыл бұрын

Lovely thanks for your feed back!!!!!

@achmadzainuri2804 4 ай бұрын

Good and thanks master

@nimanthaprabath8041 Жыл бұрын

Thank you for sharing your knowledge. It did work for me

@PatrickRibbsaeter 2 жыл бұрын

all videos amazing, thanks for doing this in English.. most videos on tv repair are in hindi..

@ElectroPixels 2 жыл бұрын

Thanks for the valuable comment

@muralidharagk3801 3 жыл бұрын

Thanks for the video sir about TV repairing the information about shorting problem i

@hasanherman7878 6 ай бұрын

hallo bro, please advice, (the case in the same panel ) if vgh, vgl, and all test point present normally, but no display.

@manojbharkad1477 3 жыл бұрын

good information sir thanks

@johnbillalcalde9748 3 жыл бұрын

Hello Sir watching from Phil.I've encouner also that kind of trouble and prrfectly fix aso like that.

@saddikuabdulrahim2857 Жыл бұрын

Thanks for the knowledge

@djp2803 2 жыл бұрын

Thanks masters from cebu pi

@KARL_AGAP 3 ай бұрын

@bernardnyuyshiyver8161 10 ай бұрын

Thanks bro your are a darling

@lalchandsharma4661 3 жыл бұрын

Very good 👍👍🙏🙏🙏

@vimalmahant5157 3 жыл бұрын

Thank you sir sharing this useful video

@ElectroPixels 3 жыл бұрын

Thanks for you're valuable comments, please share this video in all of you're groups

@shaikhussain7258 3 жыл бұрын

Good job sar

@edmundorosco3363 Жыл бұрын

Thank you for sharing sir godbless to you.

@barispandir Жыл бұрын

nice video . thanks

@ravikumargokulakrishnan3671 2 жыл бұрын

clear explanation

@dilippamnani7724 3 жыл бұрын

Very good

@deepakgupta8606 3 жыл бұрын

Nice sir

@raghulokoju8745 3 жыл бұрын

Best video

@seemakhalidseemakhalid352 Жыл бұрын

Excellent

@sandipghuge4262 3 жыл бұрын

Good sir

@saidsaad7845 3 жыл бұрын

Hi sir please i have innolux display in my samsung tv is it a good company in making display or no. Thanks

@nomendrahirwani8091 2 жыл бұрын

Ok sir thanks 😊😊

@user-lo4yv6zl3v 3 жыл бұрын

thanks:......

@RAJKUMAR-iw8ur 3 жыл бұрын

Nice information sir

@ElectroPixels 3 жыл бұрын

Thanks sir

@kevinmeyer6255 2 жыл бұрын

Thanks for the Video. You instructed to block 3 signals. I assume one is VGH, the other VGL, but what is the 3d one ?

@ElectroPixels 2 жыл бұрын

CKV

@kevinmeyer6255 2 жыл бұрын

@@ElectroPixels Isn't there usually more than one CKV signal, e.g. CKV1, CKV2, ... and also the inverted clock, e.g. CKVB1, ... ?

@zbyszekskibinski 2 жыл бұрын

@@kevinmeyer6255 It depends on the screen. CKV signals are Gate signals in some of the screens in others you get VGH odd/even X2 instead of ckv1/CKVB1 etc where these 2 lines pulse alternately between positive and negative voltage addressing odd and even lines mutually exclusively at the same time. In this case he was lucky he had the short in the left side because because the voltages and signals are routed via the master PCB on the input side so he just masked the signals. Had It been on the left side he would have had to cut the tracks

@zbyszekskibinski 2 жыл бұрын

@@mostafa221 check for shorted SMD ceramic capacitor on the half where you read 0V of when this half( of source driver panel) is connected to t con. Also run cold diode test to see if this voltage line is not shorted to ground. If you dont find any shorts on resistance test the next test is to check COF driver on the affected side. You can cut Vgh/Vgl lines neer the corner of the screen or cut the entire COF off completely. Mąkę sure you cut the right COF on correct side though:)

@josephantony5589 2 жыл бұрын

Well explanationed. Thanks Sir

@visunathan1669 Жыл бұрын

Hi bro micromax 32 inch FHD backlight is ok ,sound ok, but vgh,vgl -0v video not display need to your support tell me clear the issue.

@marioaberjedo6579 11 ай бұрын

Good day sir,I've done the same and the result...all voltages is normal except vgh with only 23v,screen appears with vertical bar

@user-tb4xl4ui5q 3 жыл бұрын

👍

@juanitovillanueva1742 3 жыл бұрын

Hello, good afternoon. Question what if the short is on the other side or right side of the panel so how can I block the clock signal on the other side?

@ElectroPixels 3 жыл бұрын

If both sides are Short then its not Repairable, in most cases the complaints is in right side that as shown in video we can block vgh, vgl tracks using tapes by blocking connection in ffc cable as shown in video, if the complaint is in left side blocking is not possible we need cut the vgh, vgl tracks going to the panel in left side

@sachinsoni1599 2 жыл бұрын

@@ElectroPixels how did you know that the 3 tracks you blocked with tape are shorted?

@Vo0d0o2009 2 жыл бұрын

@@ElectroPixels damn its the information that i search for , im on a samsung un65mu6900 with the first shorted COF in my case it affect the panel in all manner its for 99% of my sources , NOT repairable im about to try to isolate shorted lines betwerrn the cof and the pannel , i will mesure some thing before , like theses new lines ive just discover thanks man from quebec canada ( theses set have no side driver , i suspect this cof contain side drivers

@christianrowan8302 2 жыл бұрын

Thank u so much. fix my problem. but there is still a dark spot with line visible.

@ElectroPixels 2 жыл бұрын

It's just a temporary solution, Permanent Solution is Panel Replacement and its more costly so use the PANEL maximum using this type of methods then replace Panel or buy new Tv

@abgduta8254 3 жыл бұрын

my problem even i disconect the flexible..the capacitor in each cof still short..

@gustavobattista6937 2 жыл бұрын

Hola las señales lc1 lc2 en las tv lg como vienen marcadas?

@ElectroPixels 2 жыл бұрын

Lg Panel its called as vgh odd and vgh even

@user-sb8xc3gm2f Жыл бұрын

Hello Give me a solution to the problem of the image being inverted on the 50-pin screen. For information, we turn on the TV with the receiver or a demo. The image appears inverted.

@ElectroPixels Жыл бұрын

you need to enter into the tv service mode to correct invert image for that contact nearest technician

@manojsharma-yp4ll 2 жыл бұрын

And author scalars pcb chane oc on but over brightness so suggest

@shankaranil9853 2 жыл бұрын

Sir mujhe same yahi issue aa raha hai aapne jesa bataya vese mene try Kiya last 3 block kiya par phir bhi nahi aa rahi display Walt Nahi Ata VGHP VGL VGH me Jab Start Karta Hu To.. or Jagah Pe Short Ho Sakta Hai?

@Indohujan81 3 жыл бұрын

greetings one hobby😙😙😙😙

@PAL80161 Жыл бұрын

Nice good help me my tv is on

@ElectroPixels Жыл бұрын

Glad I could help

@mybikevlogs6670 3 жыл бұрын

Watching

@technoplant7058 2 жыл бұрын

Hi sir my tv same panel which is showing virtical lines if there's any solution all voltages ok

@ElectroPixels 2 жыл бұрын

May be Cof Bonding issues

@technoplant7058 2 жыл бұрын

@@ElectroPixels thanks for responding

@arvindchapde8383 11 ай бұрын

Hello sir

@ElectroPixels 11 ай бұрын

Welcome Friend

@manojsharma-yp4ll 2 жыл бұрын

I no but innolux 40" without h cof not on

@angelinajeanny8950 3 жыл бұрын

I have some problems , i've blocked the last 3 signals , picture now present , but it is like a slowmotion on the left side ... What should i do ?

@angelinajeanny8950 3 жыл бұрын

Can you help me with the problems?

@sadospan 2 жыл бұрын

@@angelinajeanny8950 Same here.... Any solution for this?

@FMJClaro 2 жыл бұрын

I have the same problem, any solucion...

@ledtvtech6531 2 жыл бұрын

Shorting to dekh knha pe hai bs tape chipka diya ho gyi tv theeek

@lungisamayekiso736 2 жыл бұрын

But if you have the same problem but the gate cof ic is burn what is the solution?

@ElectroPixels 2 жыл бұрын

Sum special cases after cutting burned track's in Cof Ic, if cof ic is at the end of the scalar pcb then image's will come, otherwise you need to change the cof ic using a Bonding Machine

@ianitang8409 Жыл бұрын

Hi i have same problem with my tv short vgh in the leftside then i block the vgh going to leftside by tape ang the came up but the problem is little white ang humbars in the leftside what should i do?

@ElectroPixels Жыл бұрын

block vgh track only and try

@ElectroPixels Жыл бұрын

Otherwise panel change

@selwyndookie5695 2 жыл бұрын

If the rightside of panel shorted how do clear short?

@ElectroPixels 2 жыл бұрын

Then you need to Trace out the vgh track point to the Right side cof then cut down that track, If both sides are short then not Repairable, After all it just a Temporary Solution, Permanent Solution is Panel Replacement