Thank you for demoing how to replace the seals. Many videos skip this part. Just finished the rear valve cover.
@cdpc2112 ай бұрын
Thank you for the video.
@michaelcarlson4932 Жыл бұрын
I've got plastic valve covers on my 2015 edge and they want you to use the same tool, crazy. Thank You for the video.
@NEWCLEARBOSS2 жыл бұрын
Thank you man. Very informative video made it easy to change my valve cover.
@gilbertmaldonado-dr2tw Жыл бұрын
Great video! Thank you for the details.
@jkjwf2 жыл бұрын
Thank you for the video. Good tips. Was that 39.5mm or 44.5mm bearing? I’m doing my 2010 Mazda CX-9 and it goes in smooth but when I get close to it sitting flush with the cover is won’t go down anymore and I even put grease on it and the cam sensor seal has a flat part only on one valve cover so is that a special grommet for the cam sensor seal?
@chriskolar2 жыл бұрын
The socket was a 1 1/8. You will have to check everything and make sure there is not something blocking the cover from going on.
@scottpolenske92243 жыл бұрын
And is the seal seat tool needed, or is there a diy weekend garage mechanic way of doing it?
@chriskolar3 жыл бұрын
In the video @ 2:24 there is a description of the socket used instead of the astro driver tool. Also to install just find a tube or pipe that fits. You may need to grind it down a bit to fit. Check different sockets a bit of grinding on them will get the fit perfect.
@jesusmolina31733 жыл бұрын
So is the same method for installing the VVT Solenoid seal on the valve cover?
@chriskolar3 жыл бұрын
Yes
@3earded_dad4303 жыл бұрын
How do you get the new seal around the spark plug tube, mine keep breaking when I bolt it down?
@chriskolar3 жыл бұрын
I lubricated it with silicone grease
@3earded_dad4303 жыл бұрын
Thank you!
@ericalynnposton86619 ай бұрын
@3earded_dad430 I'm having this issue. I'm lubricating the seals and the spark plug tube but when bolting the valve cover down the seals are pushing out. What do I do? How do I get them to stay?
@kenjimarlin4056 Жыл бұрын
How did you install the cover without busting the seals. They fit way tight when installing
@chriskolar Жыл бұрын
Each one needs lube
@emmanuelleach85662 жыл бұрын
I’m in the process of doing this on my 2009 Edge…what’s the torque specs and the pattern ???
@chriskolar2 жыл бұрын
Pattern - standard work out from center Torque - the valve cover bolts bottom out on a limit shoulder, after it bottoms out its about 15 to 17 ft lbs. I did it with a 3/8 ratchet, and tightened them up similar to a spark plug. They don't need much but enough to bottom out and then get tight. Start every one by hand first. No power tools. They will snap off easily.
@scottpolenske92243 жыл бұрын
What's the torque spec and pattern of the valve covers?
@chriskolar3 жыл бұрын
Sorry for the delay in replying. please forgive me Here is a link to my one drive. this is a picture of the valve cover, each bolt is numbered and the torque is 89 inch pounds. 1drv.ms/w/s!AitPxTb_Rl8wvHkHHyyqrvrCHA_9
@Howitis7133 жыл бұрын
How much a repair like this cost... I have this problem during this winter storm in Houston tx
@chriskolar3 жыл бұрын
The gasket set is about $90. The labor is about 2.5 hours. For a shop that's about $400 for the whole job. I would not want a cheap deal on this type of work. If they damage something it could lead to many problems. Get a good mechanic you can trust.
@Howitis7133 жыл бұрын
@@chriskolar ok thank you so much at least I have an idea of the price... Now I need to find a honest person to work on my suv. God bless
@ChrisB-cx6td3 жыл бұрын
@@Howitis713 valve cover with installed seals are about $100 each on parts geek or from the dealer