Man he is fucking bashing the lock with the hummer if you look close the lock got a dent the jig is good the operator rough

Pl )

😂😂best hammer for the job. 👍

Scary isn't it when you think a labourer can come along and achieve the same finish.

@@liammccormack7894 though you do need to have some skill with a router. It frees up time to do other jobs. 👍

Although you can use the jig for a mortise, they don’t make a cutter long enough. I use a Souber

Yes they are great tools and last as well.

Hi Ryan, I have tried the trend hinge jig. I bought it as soon as it came out. But I didn’t like the fact that it’s set out from the middle of the faceplate and not the spindle. Also all of the plates that are needed. This jig has the advantage of cutting the spindle, through holes and key hole types as well. Have a look on Facebook. There are some there that have them already and like them.

it's the same setup as the hinge jig, 12mm cutter and a 16mm guide bush. You could also use a 12mm cutter and a 17mm guide bush, just use a 5mm spacer instead of a 4mm spacer in setting up.

My apologies for the late reply, most Poe-le using these jigs use a 1/4“ router and they are fine with this jig. You wouldn’t be able to do the mortise with a 1/4” though. Even with a 1/2” router they don’t make a cutter long enough to do the full depth of the lock. Most use the Souber.

Hi Gavin, yes your right. If you have a good run then it is an investment. 👍

Hi, the jig is £415 plus vat. You can join the Facebook group. It’s B W Jigs’s or you can purchase them at www.bw-jigs.com

Hi Danny, one jig will do all but you would need to change the lock type plates. You use a 12mm long reach cutter with either a 16mm guide bush(4mm spacer) or a 17mm guide bush(5mm spacer). Are you on Facebook? There are videos on setup and other vids. Look for B W Jigs

@@benweir8173 OK I'll give it a look. That's handy, 16mm guide bush 12mm cutter is the same set up for the hinge jig so saves all the faffing about switching stuff over👍

Yes, I work on price work and don’t want to waste time changing cutters. Straight from the hinge jig, onto the lock jig.

@@benweir8173. Hi can you please give me some information how and where can I get and how much is thank you Bekim

@@bekimberisha1328 hi mate, I’m a new company and haven’t set up the website yet. But contact me on my email. Ben.O.Weir@gmail.com

من دواعي سروري يا سيدي

Hi Jane, that one was the prototype. It was the third one out of 6 before we had the final design.

The jigs have a 32mm thrust pad housed into the jig on the inside that spreads the pressure. Quite a few users of the jig have worked on pre finished doors and haven’t had any problems.

I used the Souber for the mortise.

Hi Jurek here’s a KZfaq video on the set up. kzfaq.info/get/bejne/kNqida6HstLLiZc.html

Hi the jig is from BW Jigs and you can get them at www.bw-jigs.com

Hi mate, are you on Facebook? If you are, look up B W Jigs. There’s videos and and photos.

Hi, the jigs are out of stock until the 22nd. They cost £415 + vat. They come with 3mm spacers, Euros and Bath Privacy plates. If you would like one send me your contact details to info@bw-jigs.com and I’ll send you a PayPal invoice. Delivery normally takes up to two days. Let me know if I can help further.

Sure, it’s great for long runs. I don’t think I would use it for one. 👍

@@benweir8173 cuánto sale la plantilla de encastre de cerradura y como ce ac llega el güiro de $

Hi Drew, they are £415 +vat. If you are on Facebook. Have a look for B W Jigs. There’s some videos on there on set up etc. Thanks.

Hi Eduard, this jig is one of the earlier prototypes. The finished jig is anodised black. You can get them at www.bw-jigs.com. 👍

@@benweir8173 Thank your so much 👍

Yes they are expensive £415 + vat but it doesn’t take long to get your money back. 👍

Hi Dan, you can purchase the jigs at www.bw-jigs.com

@@benweir8173 👍

Yes. Contact me in info@bw-jigs.com 👍

@@benweir8173 I will email you right now for info on this .

I had some questions on it as well I did just send a email on it

@@chicothesavage ive replyed via email. thank you.

It’s EQ1010 festool router

Hi Wayne you can contact me in info@bw-jigs.com thanks

Many have said this and I’m still waiting to set a video😂😂 I have seen some fit a lock in 6-7 mins using an mdf jig for a faceplate and drills for spindles and bath privacy’s for the finish looked like a rat had been chewing at it but I haven’t seen it done by hand in that time. Also where this jig comes into its own is on Euro cylinders.

Sorry, I don't understand

hai, biaya jig, £415 ditambah tambahan £75 untuk pengiriman di luar Inggris. jika anda tertarik beritahu saya. Salam, Ben Weir

@@benweir8173 kalau jadi Ringgit Malaysia baerapa bos

@@muhammadagushariyanto5092 RM2 2654,54

Yes i cut the mortise with a Souber jig.

Hi Lukas, sorry you don't like the jig, not for everyone I suppose. but the jig doesn't only do the faceplate. it also does the spindle, through bolts and a range of different keyhole types like euro cylinders as well. Although you use something else to do the mortise there is still no quicker way. It takes a minuet to do the mortise and 3 mins to do the rest. ideal for price work.

It depends on the job. I’ve had as little as £3.50 years ago to £25 a lock more recently.

HOW MUCH IS THAT IN DOLLARS PLEASE.@@benweir8173