How to Load and Prime a Grease Gun (new for 2023)

Рет қаралды 211,326

Күн бұрын

In this comprehensive update to our most-viewed video, we'll guide you through the essential steps of loading and priming your grease gun. Whether you're a beginner or an experienced user, our step-by-step instructions will get you loaded and greasing quickly and easily. Say goodbye to messy mishaps and greasing frustration with our grease gun loading and priming tutorial!
SHOP NOW: locknlube.com/collections/gre...
00:00 Introduction
01:02 Loading The Grease Tube
02:35 Reassembly
04:25 Priming Basics
05:33 Troubleshooting
06:03 Tip #1 - Loosen The Barrel
06:50 Tip #2 - Air Bleeder Valves
08:15 Tip #3 - Follower Rod Pressure
09:32 Tip #4 - How much grease is left in my tube?

Пікірлер: 30

@FD-dh2fu 10 ай бұрын

I never understood how the plunger can go all the way back up even though the cartridge is full. Unlike a caulk gun.

@sonofthehills 4 ай бұрын

probably been using a grease gun for 60 years. Still learned a couple of tricks! Thanks!

@GXMAN16 Жыл бұрын

I bought your green gun thats featured in the video. Unfortunately ive misplaced the instruction sheet, as the gun laid for a few month before the first use. So this video was very helpful in helping reprime the gun, as i didnt know what the technique was when the gun stops pumping and i have more than half a tube left! Very great gun and makes relubing the driveshaft very easy. Remember people if you have a Toyota/Lexus body on frame vehicle you gotta grease the drive shafts and u-joints every 15k miles!

@johnwesley8327 9 ай бұрын

Indepth, well done video. Your products have come to my rescue over the years Thanks!

@montans002 2 ай бұрын

Honestly thank you for a understandable explanation and no annoying sponsorship blab before the beginning of the video like in other channels

@LockNLube Ай бұрын

We only talk about our own products so hopefully that keeps the blab to a minimum. :)

@robertpiontkowski2164 Жыл бұрын

Really appreciate this , great video 👍🏻

@Police19005 11 ай бұрын

Great video!

@patmancrowley8509 Жыл бұрын

Thanks!

@marekwieckowski7038 10 ай бұрын

Thank you.

@FreeLifeLessons101 2 ай бұрын

Great video! Huge help.

@jimsmith8071 11 ай бұрын

Good video. I have been using grease guns for 50 plus years. To save time I always put pressure on the follower plate when reloading the gun. It is the quickest way.

@alexfinley7849 Жыл бұрын

Very helpful thank you!

@LockNLube Жыл бұрын

Thank you Alex, we here at LockNLube appreciate our efforts to help our customers, as always if you have any additional questions you can always reach out to us at 603-795-2298 or sales@locknlube.com.

@safetydepartment 10 ай бұрын

man the LNL351 looks like a beast. I can't wait to get mine. I just need to find something to grease now... 🤣🤣

@artschulte1897 27 күн бұрын

Good video and cplained everything about the plunger and air release

@Pete.Ty1 Жыл бұрын

👍👍👍Thanks

@earlewhitcher970 Жыл бұрын

Not a lot of new information here, I've been using grease guns for for almost sixty years, but there was some new tricks that made watching worthwhile. Thank you for such an informative, relevant presentation.

@LockNLube Жыл бұрын

Thank you, lots of folks have never used a grease gun before and we talk to people all day long who need help with the basics. We pride ourselves on that level of customer service and these videos help with customer eduction. Appreciate your comment and have a great day.

@charleslopez9472 Ай бұрын

Thank you for explaining the follower plate. I kept trying to figure out what the "drop" was in the t-handle which I thought dropped into, and not away from, the cylinder. Also didn't know if when priming, to pump the handle while pressing the release valve, and if to do this while the cylinder is still a few turns loosened or not. ALso, I think I understand a bit more about locking the t-handle onto the following plate and if I released properly before using, or is I ever really locked onto it at all.

@Changtent 11 ай бұрын

Good video thanks. One common problem I've found with cartridge grease guns is getting the follower plate to start into the end of a new cardboard tube. The solution that I found was to notch the follower rod about 1/4" longer than the factory notch. This causes the new cartridge to hit the follower plate a quarter inch before fully seating. You then remove the tin pull-tab plate, and rotate the new cardboard tube while pushing it into place using your fingers. This method insures that the follower plate has entered the new tube before you install the pump head, and removes much of the air from being trapped at the pump end. (Just swipe off the excess grease before installing the pump head.)

@LockNLube 11 ай бұрын

This is a way to do on cheaper grease guns that don't give you the ability to lock the follower into the T-Handle. All or our full size guns give you that option.

@meseahunt Жыл бұрын

thanks, now u can clean up..... 🤠

@bksaun 9 ай бұрын

Where are these grease guns made?

@LockNLube 9 ай бұрын

The LNL351 is made in our partner facility in South Africa.

@user-dc7pm2eo1z 9 ай бұрын

In the grease gun manufacturing factory

@SrsLe33 2 ай бұрын

My pos gun won't suction

@LockNLube Ай бұрын

Give us a call, we can usually talk you through any priming issues right over the phone, or process a warranty claim if there is something wrong with the gun (rare). 603-795-2298

@kiwifarmer7254 2 ай бұрын

what is causing the grease to come out along the rod when you pull it back out, sometimes there is more than half a tube of grease on on the wrong side of the washer ,mixed with the spring , you think that gun is empty ,as it doesn,t pump anymore ,anoying

@LockNLube Ай бұрын

Do you mean one of our guns specifically?