Over the last 4 years, I think I've seen this video at least a billion times and will probably see it another 20 billion times in the next couple decades cause of this damn pin and collar system

Mark saving the day as usual. Word of advice: Don't resize your bracelet over carpet! If you drop the collar on the carpet, it's GONE! And as Mark said, the pin will not stay in the bracelet without the collar.

Your service is incredible. Highly recommend Long Island Watch.

I watched a lot of videos on how to adjust my Seiko Prospex Solar watch band, but your video is the only one that actually worked. Thanks a lot for the helpful video.

This video taught me how to change my bracelet size! Extremely helpful. If like me, you don’t have the proper tools at home - patience, needle nose pliers, and a sewing machine needle do the trick.

I helped a friend shorten his SARB033, and was pleasantly surprised when I saw the collar on the center link. That was way easier than having the collar on the outside edge. If I hadn't watched your #15 video with pins and collars, I wouldn't have had any idea what was going on. Thank you for these videos.

I got a deck monster from my coworker. As soon as I put it on the watch fell off my wrist. I packed the watch away and I was able to fix it today. Happy I got it going. Watched the video after I did the repair and confirmed I did it correctly.

Love your videos, they are always always so informative. Save me a lot of frustration!

just wanted to say thank you you saved me so much time and educated me i enjoy yours and the urban gentry's channel such great info

Super helpful. Thanks! I was losing my mind over why the pins kept falling out!

Oh geez I'm so glad I found this, thank you for posting it! For future viewer reference; the SBDC047 Transocean also uses this pin and collar set. Thanks again Long Island Watch for posting these helpful videos!

Reeeally wish I would have watched this first... All the pins fell out of my watch while I was running down the stairs.

I had no idea where the collar on my desk came from and immediately went to watch your video. Thanks a lot!

This took me forever to realize on my Oceanus T200. I was sure there was a collar but didn’t know where it was until it fell out. Thank goodness I had a towel to catch it. Then i spent ten minutes putting the collar into the wrong side of the link, then dawned on me to check the hole sizes. This video is so helpful. You do great work, Marc

Excellent video! Caught it just in time, have a couple of Seiko's I need to size. Thanks for taking the time to post and share.

OMG... Bro you completly read my mind. Just bought the 033 and I wasn't really sure what to do lol. Talk about perfect timing

Mark is simply a legend. Sizing my Seiko SBDY029 Samurai - watched the first vid - thought that doesn't seem right. Watched the 2nd vid about pin and collar - still struggled. Watched this and it was spot on. Thanks heaps.

You have the best vid on how to size pin and collars on the turtles. When I got my SRP775 I was worried that I’d have to take it somewhere to get it sized, but after watching it I had it done in no time. Thanks for all the help.

Marc, this is a terrific video. I just got a SARB033 and sized it in about 10 minutes thanks to your instruction. (You sold out as I was ordering from Long Island Watch.) Sizing would have been a disaster without your help. Thank you, my friend.

Cheers mate the battle finally has been won

Life saver! Thanks for this. I learned many new words, and lost a year of my life to stress, trying to get a Sarb033 collar back in the hole in the outside part of the link!!!

just got my SBBN031 and needed to remove 1 link from each side. I could not have possibly done this without your video! Thanks for doing these.

Very valuable content for all SARB033 owners who want to adjust their bracelet themself.

Thanks for the helpful vid. Just got the samurai srpc93 and was clueless when I saw the small collar laying on the my table after freeing the link. So glad I found Ur vid. Big ups! 👍🏽👍🏽👍🏽

Thank you Mark. This video helped me resize my new Sarb033. It gave me the confidence to do it myself. So easy once you know what to expect. Thanks again.

Just went through EXACTLY what you described at the beginning of the video with my SARB033 (purchased from you last week). I was losing my mind trying to get the collar into the outside of the bracelet. Finally tried the inside and it dropped right in. Had to laugh when this video popped up in my feed. I already adore the watch. It's going to be a mess in a year because I'm going to wear the crap out of it. Don't care... I'm going to enjoy it.

Thank you so much! Saved me a headache and a trip to the jeweler's.

Wow, that collar is a lot smaller than it looks in the vid. Didn't realize how magnified it was. Thanks, Marc!

Thank you so much for this video, I was trying to figure out a spb077 bracelet for hours. This is the only video I could find to figure out Seiko center link colars. Thanks for the wonderful content. 👍

Bro you saved me with my sarx075. Hearing that you made the same mistake also let me go a bit easier on myself ❤

Marc; great video! With your clear and concise instructions, you taught me how to resize my own bracelets. No more going to the mall kiosk! LMAO!! Thanks so much for these incredible "Watch and Learn" videos. They are so useful!! Cheers, bro!

NEVER have my fingers felt so fat! I am detail oriented, not clumsy and I'm generally patient with fiddly jobs but this was one of the hardest things I have done. Total pain in the axx. Not only that, but I lost the collar no less than three times on a worn hessian rug. Cannot believe I was able to find the thing each time. Anyway, your video was a godsend. Thanks. Phew!

Thank you Mark. You put a lot of dedication in your work.

Best Seiko link adjustment video out there, thank you!

Thanks Marc, I’m expecting the SARB035 today so this video definitely helped.

This is excellent mark! Thanks for this video. I guess I’ve been spoiled none of my other watches have this setup.

I can't thank you enough, Marc, for this video. I've been avoiding sizing pin/collar bracelets for years. I can't tell you how many collars I've lost during sizing that ,seem to disappear into thin air. Instead, I've bought straps, Strapcode bracelets or had a professional do the sizing. Thanks to you and this video, I now have several OEM bracelets installed and sized; and others to come, saving me $$$ in the long run.

Save my life with this video

Thank you Marc! That is the right design for a pin and collar bracelet, in my humble opinion. I believe that’s the design my Omega SMP had. Collars on the outside of the bracelet are unnecessarily difficult.

Great video! I watched your previous video and was surprised when I received my Orient Triton and it was this style. Based on the information I had already learned, and a happy accident where the collar fell out on my table (not lost), I was able to size the bracelet without a problem. Thanks again, Marc!

Thank you, this video made it easy for my first time.

Thanks Mark, wonderful video

Extremely helpful. Thank you.

Thanks again! Always informative ! Keep these videos coming !

Thank you for this video. You really saved my ass because I didn't notice the collars when I removed the pins from my watch. I actually found the collars on my floor after watching this video 😄

Good video Marc! I got one of those from you not long ago and, as my first encounter with pin and collar bracelets, I did have a wtf moment when I removed my first link. This should make it quite easy for new buyers. :) Thanks!

Perfect Mark, just what I needed, thanks

Fantastic explanation! Thank you very much

Nice tutorial, thanks.

Finally a tutorial that's not full of bs and gets straight to the point.

Thanks for the video. This is just what I needed.

Great video, really helped me!

Thank you. Great help.☺️👍

Good info. I was just going to take mine in to get done . I still will but this is good to know . Thanks .

Excellent video as always.Thanks.

Thanks for the help!

Great video, this really helped.

Thank you for this video! I didn't even know about the collars and had drop them. Luckily I found them on my carpet near where I took it apart. BE CAREFUL GUYS, these are really hard to replace it seems

Great demo/explaination Video!! Thanks.!!👍

Really helpful thanks!

Very useful. Thanks.

Hey thank you so much! I finally got it! Never new what those small tunnels were! Mil Gracias and Happy Thanksgiving

Marc, great and useful information here. While I do not have the watches you referenced in the video, I did recently purchase a Rado Golden Seahorse that has a beads of rice bracelet that I needed to resize. While I have resized numerous watch bands for myself and other over the years and have an accumulation of numerous tools for that task, I was struggling trying to remove the pins on the bracelet. I knew the bracelet was a tube and pin type, and I had never resized one of those types before. I watched numerous You Tube videos that all noted how the tubes were easy to lose, so I approached with caution. Using my existing tools I was able to get one pin about one quarter of the way out but it was very tight and refused to pull out even with a few gentle tugs with my pliers. On this bracelet there are no arrows to indicate which direction the pins should be removed, so I thought perhaps I was trying to remove the pin in he wrong direction. I put a pause on my efforts and tried to gather more information, but I could not find anything on a tube and pin resize on a beads of rice bracelet. You should also note that most of the videos that focused on this resize would show a close up of the tube on one side of the bracelet near on edge. Under magnification, I did not see that on my watch, so I was puzzled. Yesterday, I watched you video and the light bulb went off when you noted that the tubes in your Seiko watches were of the internal type. I also saw that you used a pin pusher that was much longer than the ones I had, so I ordered a few after measuring the diameter I needed (0.80mm). This morning I tackled the resize and with he new pin pushers, the pin came right out, but no tube. I realized I needed to push out the tubes separately from the middle links. The beads of rice bracelet makes this task very cumbersome and you certainly need patience, but I took my time and was able to remove the two links to fit my wrist. Your tips and comments were invaluable in both giving me the confidence, using the right tools and understanding what I need to do, so I waned to say, THANK YOU, and let your other viewers know that you do a great job in your watch and learn videos. Best regards.

Thank​ you.​ I​ figure​d​ how​ to​ resize​ my​ band​ cos​ of​ this​ video​

Mark, God bless you.

Thank you so much for saving my day 😅

Thanks, this was a lot of help

I wish I saw this video before I spent 1.5 hrs with my Seiko Prospex Solar Chrono Diver SSC675p1 last night. I saw your other video on pin and collar bracelettes and couldnt figure out why the pin wouldnt come out. You definitely need the small longer punch to disengage the pin from the internal collar, as the shorter ones on the vice-type pin-pushers don't go in far enough. Once I got one out and finally saw how it worked, it was a little easier. Great video.

Thanks for tutorial.. done

Thanks Marc.

I wish you had made this video a month or two earlier! Luckily, I was able to figure this out based on your previous Seiko sizing videos (where I learned what a collar was), and that I got lucky noticing the collar all out. So thanks again for your videos!

Thanks, Mark

Thanks for this 🐨

Many… many thanks!!! 🤝

Thankyouthankyouthankyouthankyouthankyou! I wasn't the least bit frustrated before I found this video. Nosiree ....

Nice one Mark thank you😊

Thanks Mark, you just saved me $20 (minus what it cost me for the tools!). But it was satisfying to be able to size it myself. Things seem to be countersunk well and I have the micro adjustment in the middle so if I'm off a little I can adjust. Kind of a pain though, I can see why people are going to screw. I just sized a Deep Blue and that was another new type. It had screw heads on both sides with one side a pin and the other a tiny screw with a sort of spring. I had to use a screwdriver on both sides to open it and close it. Not sure what that is called. Again thanks!

you just saved me close to $100 with this video, thanks haha

Super helpful, ty :)

Thank you so much!!!!

Great vid, thanks so much :) super helpful.....PS, is that actually a Breitling Navitimer? For some reason I thought it was a Breitling Aerospace titanium.

Thanks and thumbs up.

Thank you.

The pin and collar style was confusing. Thanks for clearing it up for me!

Thank you man 💯

Thanks Marc. If you end up getting the new Strapcode/Miltat oyster bracelet for the SARB033, would love to get a closer look at it.

So that's what that little piece was that fell out. Good thing I kept it. Reinstalled. Tnanks!

Great video! I did run into one problem though. When I pushed out the pin I found that the collar was still stuck in the link. I have tried to remove the collar but it won’t come out. What should I do?

I really wish I had not taken your advice on removing the spring bar at the clasp. I have tried and tried but am still unable to replace it. For now I have a spare bracelet for a SARB that's currently on leather. If anyone has any suggestions they would be greatly appreciated.

Hi mark i own the 035 and love it , i also like the bracelet apart from gaping buckle and worst of all just the two adjust ment holes. I like my bracelet s tight but cannot adjust it correctly , i either cant close it at all or it slips over my wrist knuckle which i hate , i guess ill have to invest in an after market. Take care.

Thank you, Sir...

Thanks Marc for these videos! I was on the edge of collapsing when adjusting my Seiko Samurai, because I assumed that the collar goes in from the side and saw immediately that it is not possible in any way. After watching the video everything went smoothly and now I couldn’t be happier with my Seiko! 👍🏻😊

How do you put it back together after resizing it? I've been having some trouble with the spring pin and getting it back in

Similar system on the Alpinist watches. I (stupidly) did the bracelet change on my couch, expected cotter pins instead of pins and collars, and lost two of the collars. By the grace of the watch gods, I found the collars! Should have watched this video before... I think it makes sense to install the pin the same way it was removed, that force you apply would drive the collar into the middle link instead of the side...if that makes sense.

Aerospace Mark you legend

Thanks...this pin and collar system also needs to be revisited by Seiko..its a frickin nightmare!

Hey there Marc. Love you vids, especially that sense of authenticity that you bring to the table. It's something I try to give my reviews too :-) Anyways, I recently got the white Citizen BE9170 and was so impressed with it that I ordered the black version too. No, they don't feel as premium as my Zeppelin moonphase or as robust as my Orient Ray II, but for the price I think it's an awesome watch. The size, that domed crystal, and the way the dial plays with the light is pretty remarkable. I see you're selling them over at LIW too...any chance for a bit of a review from you?

If I'm correct, reassembling in the correct reverse order is somewhat necessary. As the pin goes through the collar the force of it going through would actually tighten the collar around the pin due to the tapered center link hole.

Apologies for the question: is this the same type of bracelet on the SNE363P1 model?

It was driving me mad, thanks man.