@charredskeleton 4 жыл бұрын
I have nothing but encouragement for you! Never stop wrenching!
@carloslopez9153 5 жыл бұрын
“ you gotta do what you gotta do to make it to the truck show “ ~ Ricky 😂😂
@sterlingayden4863 3 жыл бұрын
you prolly dont care but if you're stoned like me atm you can stream pretty much all the latest movies on instaflixxer. Have been watching with my gf for the last couple of weeks :)
@lanereuben6461 3 жыл бұрын
@Sterling Ayden yup, I've been watching on InstaFlixxer for years myself :D
@troycallan4776 3 жыл бұрын
@Sterling Ayden Definitely, been watching on instaflixxer for months myself :D
@ericramos5183 5 жыл бұрын
Slowly slowly taking baby step - Ricky 🤙🤙🤙 Same bro with the Tahoe might get some honeycombs
@austinashby736 Жыл бұрын
Was the front at stock height before you cut them cuz I’m about to do a flip kit on mine and I was told to cut two coils off the front for a 4 inch drop in the front
@jorgegraciarubio8014 4 ай бұрын
How big is the coil already cut, bro?
@mjsmjs522 4 жыл бұрын
I'm surprised that front drop down pretty low for that little bit of a cut I'm thinking of cutting mine but I don't want to go that low you think I just need to go a quarter of that half that you cut
@trucktalk9467 4 жыл бұрын
Yeah that’s what I would do because I cut a coil and it dropped it that much so with a quarter I’m sure it would be a little higher
@hussle4ebrand361 3 жыл бұрын
Just subbed bro
@trucktalk9467 3 жыл бұрын
Appreciate it bro
@Treyes92 4 жыл бұрын
Do you remember how much cutting the spring lowered it?
@trucktalk9467 4 жыл бұрын
Tlaloc Reyes about a inch bro
@blacang3l 4 жыл бұрын
Finney county representing here from ford county
@chrisrideout6868 8 ай бұрын
That c notch dont look to safe
@emmanuelgarcia8951 4 жыл бұрын
que tanto baja cortandole el sprimg
@ernestovillasenor706 2 жыл бұрын
mides el spring parado y lo marcas , cada pulgada que cortes del spring son 2 pulgadas que vaja
@txjulioo281 3 жыл бұрын
How much do of the spring do i have to cut to make it a 4 inch drop in front
@trucktalk9467 3 жыл бұрын
Like a coil and a half
@Danny0905 8 ай бұрын
So with that half inch u would have 2 inch drop
@jesusgonzalez2677 4 жыл бұрын
How did you fit the jump seat
@trucktalk9467 4 жыл бұрын
Jesus Gonzalez you have to make brackets bro
@sergios95obs60 5 жыл бұрын
What part of Kansas are you from?
@trucktalk9467 4 жыл бұрын
Sergio's 95 obs garden city Kansa bro
@carlosmata3527 5 жыл бұрын
How does it ride with cut coils
@trucktalk9467 4 жыл бұрын
Carlos Mata it ride good since I had the lowering shocks
@florentinocastillo7180 2 жыл бұрын
What song is this v
@mctcustomz6860 Жыл бұрын
Great job my boy but next time don’t use a grinder on springs as for they are heat cured use a sal-saw or ban saw
@dukezity5226 10 ай бұрын
Chopper
@danielsklogsv2327 2 жыл бұрын
Bruhhh I cut 2 coils 🤦🏽♂️ , do you think it’d work? I feel like that’s too low
@obskiko Жыл бұрын
how low did it go
@danielsklogsv2327 Жыл бұрын
@@obskiko low asf 😭 I was almost touching the ground, and I’m not over exaggerating 😂 when I put a lip on it, it was touching the floor
@obskiko Жыл бұрын
@@danielsklogsv2327 bro i cut like 2.5 and my wheels didn’t fit anymore😂
Moore Motorsports Garage
Рет қаралды 6 М.
EATON Detroit Spring
Рет қаралды 291 М.
Tech Stuff
Рет қаралды 144 М.