LS Darton MID Sleeve Installation - on the HAAS! (Part 1)

Рет қаралды 8,765

Жыл бұрын

This is part 1 of explaining the process behind our LS Darton Sleeve machining and installation process.
*** Follow Us On Social Media ***
wolverineen...
wolverineeng...
www.woverineengines.com

Пікірлер: 33

@bookerol 7 ай бұрын

Reminds me of the late '70s when we installed this type of sleeve in the Vega blocks, when the coolant sides were badly corroded. The std. sleeve was a pre-finished flanged sleeve. All manual machining in those days.

@rvarsigfusson6163 7 ай бұрын

Joyful to watch..... really like it to see the know how to fix it to be a better one and Elcheapo as well.

@Airman.. Жыл бұрын

Really cool machining. Subbed

@wolverineengines6156 Жыл бұрын

Thanks!

@lexustech48 9 ай бұрын

Congrats, you earned subscriber #400 here! :)

@wolverineengines6156 9 ай бұрын

Thanks for subbing!

@cartermackenzie1135 4 ай бұрын

Can you do this on a gen 5 motor?

@jorisdeckers2270 10 ай бұрын

Hallo nice job and video thanks what is the diameter off the bar? what is the height off the center off the bar to machine table? greetings joris

@wolverineengines6156 9 ай бұрын

11" off of the table. 2" diameter bar

@MrMrBigro 7 ай бұрын

Can you do the same with cast iron block ?like the1990 taurus sho 3.0 block?

@wolverineengines6156 6 ай бұрын

No cast iron wouldn't be cost effective as it would add a ton of time!

@jamieblubaugh5153 Жыл бұрын

Very good video! Do you have one or are you going to make one machining for dry sleeves? What is the cost for a dry sleeve setup? Where are you located?

@wolverineengines6156 Жыл бұрын

Thank you! I haven't done a dry sleeve video yet but I am planning on it. The dry sleeve runs about $2500 with the sleeves and using your block (we can also provide the block). We are in Fort Walton Beach, FL.

@philortega6516 Жыл бұрын

@@wolverineengines6156 I'm looking for an LS7 block for my 09 z06, My engine is still good,but looking for a back up. Its a daily but I want to autocross it once to three times a month. What would the cost be for the dry vs wet if I provided the block.

@wolverineengines6156 Жыл бұрын

@@philortega6516 Right now we are not taking in new job as we are so far behind. Please check back with us in a few months!

@johnchambobly6436 8 ай бұрын

Why 5.3 block in particular? And can all 5.3 block be dry sleeved?

@wolverineengines6156 7 ай бұрын

5.3L is the cheapest. Any aluminum LS block can be done.

@Airman.. 9 ай бұрын

Question sir, does Darton dry sleeve require a .002 above deck protrusion or it should be milled true to the deck?

@wolverineengines6156 9 ай бұрын

Flush for 90 percent of applications. Much easier to get right. I have left them up .002" for high boost applications but it's hard to keep everything even and parallel.

@Airman.. 9 ай бұрын

@@wolverineengines6156 Roger that. Thanks

@nextgen1939 8 ай бұрын

How much z is in the machine? Did you have risers put in? Im trying to put my fadal online to do this.

@wolverineengines6156 7 ай бұрын

32" Spindle nose to table.

@nextgen1939 7 ай бұрын

@wolverineengines6156 Thanks for the reply. I have 28 in the z right now. I am looking to make some risers for my z-colum but didn't know the best total z heigth to have.