stock bottom end LS1 , stock heads 853's . super vic with nitrous outlet puck system. 250 shot 8.95@149 1.20 60ft(back tire)
Пікірлер: 111
@MrTrollus10 жыл бұрын
Sick 60' time. That time is all in the suspension setup
@bigdondre6 жыл бұрын
It's definitely possible. He has a lot into the suspension and a huge stall, good tire, good fuel and tune. Maybe the whole car is lightened a lot. Better rear gears also. That suspension is set up sick. For those who know racing suspension is just as important as motor.
@alphaninja02025 жыл бұрын
Some people could argue suspension is even more important xD
@TheDevin91810 жыл бұрын
How much timing are you running on the 250 all on pump gas?
@HELLOPUFFIN10 жыл бұрын
can I ask what cam it is without trying to sound snoopy?
@lmadden62367 жыл бұрын
How long did that last?
@javilsx3635 жыл бұрын
How much is the rear end narrowed?
@ImaginnationWereWolf8 жыл бұрын
Did he spray on this run?
@independentassesor26302 жыл бұрын
What Cam were you using? What a beast
@Crazyquad068 жыл бұрын
sounds like my LS1
@characterdevelopment23615 жыл бұрын
How much did the car weigh
@jaayyvee7 жыл бұрын
how ?
@BSmiffDaIllest10 жыл бұрын
Says 250 shot in the description
@vic218610 жыл бұрын
Killer times..what times you think it will run on pump 93?
@so-flamotorsports74913 жыл бұрын
3.boom
@steveni003189 жыл бұрын
The car would not survive a 250 shot on pump gas. He's running good fuel.
@johnsalary51885 жыл бұрын
I ask why couse I own a 2000 stock bottom end ls with arp studs when I had the 6 speed I was dumping my spec 3 clutch at 7000 rpm an shifting at 6800 now we have a 400th 3 speed an I’m setting my 2 step rt at 3400 rpm an shifting at 7000 an my motor been holding up fine
@BurntToastFTW3 жыл бұрын
video never says it was on pump gas?
@MsJohnboy303 жыл бұрын
What kind of fuel pump you running i have almost the same set up but I can't get my nitrous to work it backfire through the intake my plugs look white it's running lean
@alsharshani2 ай бұрын
Aeromotive A1000
@dubcoder10 жыл бұрын
it doesn't matter if he stood there for 10 seconds before going, it;s all timed by when you actually leave the line :)
@dxracing995 жыл бұрын
Good job Brother! Rear end gears?
@alsharshani2 ай бұрын
3.70
@BSmiffDaIllest10 жыл бұрын
You check your rear end alignment under the car? That thing is hooking left HARD in the air. No bueno there.
@redrumss346423 күн бұрын
Suspension and th350
@danielxj65986 жыл бұрын
What transmisión??
@alsharshani6 жыл бұрын
Daniel Barbosa TH400
@stevebroglin36195 жыл бұрын
I don’t see no time I thin it said 10. Something
@smithperformanceracing58486 жыл бұрын
Well there getting 500hp or bit more out of these stock block 5.3s with cam only and good intake injection set up. On top of 250 shot and we all know if you run NOS alot you can pull more hp off a 250 of NOS. Good suspension, less weight yeah it sounds bout Right the time he's saying.
@deetm62626 жыл бұрын
5.7*
@bnastystuntz6 жыл бұрын
def not 500 hp on a 5.7 cam only.. Not happening.....il bet my car on it... we will go get a stock f body and u throw whatever cam in it and i u wont get anywhere close
@smithperformanceracing58486 жыл бұрын
Bnasty Stuntz it's done everyday dude. Google it......
@smithperformanceracing58486 жыл бұрын
And he's running a killer intake set up btw. I'm building a LS1 lS9 5.3 80 mm bed mounted turbo S10. Think I know sum bout these engine combos..
@smithperformanceracing58486 жыл бұрын
Bnasty Stuntz also he's running suspension and high stall converted..
@chriswinters17883 жыл бұрын
What carburetor are you running? And just the msd 6014?
@alsharshani2 ай бұрын
Fuel injection with stock LS1 ECU tuned
@BornToBeFamed6 жыл бұрын
Gotta be a stock bottom end lq9 if anything lol.
@bnastystuntz6 жыл бұрын
BornToBeFamed with them 853's they better be worked/milled something
@BSmiffDaIllest10 жыл бұрын
Thats just the camera shaking. It was a no time shown pass.
@TwinTurboLsx7 жыл бұрын
So basically cam only stock cube ls1, with a 250 shot? where does the other 200-300hp come from it would take this car to run that time? it would take 890-900 hp for that car to run that time. and that's figuring it weighing a total of 3200 lbs. Stock they weigh 3400. nice car and nice time. but this engine Def got more going on than just a 250 shot, on stock cube. 408ci maybe?
@VegasRT5005 жыл бұрын
That is why I call BS on the engine and trans claims.
@Ginajenns5 жыл бұрын
Youre an idiot … Mr twin tubo LSX lol RACE WEIGHT . This car weighs under 3k lbs
@timothygardnerjr.73744 жыл бұрын
Bazooka Joe i
@SheerMayhem Жыл бұрын
Heads/Cam LS1 has been low 9's, without any nitrous. Keep crying!
@TwinTurboLsx Жыл бұрын
@@SheerMayhem im sorry you dont recognize when someone is Bs'ing you. cam only Ls1 with a 250 shot would be lucky to crack 650 wheel hp. that is not close to enough power to run an 8. Calculating it out a 3250 lb car would need 900 hp to run an 8.95. Thats assuming they cut a ton of weight off the car and not counting the drivers weight.
@zunetrav49 жыл бұрын
To run that on a SBE and stock 853's is crazy.
@tommys29797 жыл бұрын
Travis Collins it said stock bottom end I highly doubt they have stock heads
@zunetrav47 жыл бұрын
RptrKlr 57 I would think so too but description says stock 853s. Crazy if true
@zunetrav47 жыл бұрын
RptrKlr 57 Description basically describes it as a cam only car on a 250 shot.
@tommys29797 жыл бұрын
Travis Collins oh shit it does say stock heads lol I wonder if they're just worked
@jayg788810 жыл бұрын
Nitrous or N/A?
@stevebullock60849 жыл бұрын
how the heck is that stock bottom holding up....
@SheerMayhem8 жыл бұрын
That car probably only makes 650-700rwhp. They can survive at that power level. especially in a light as hell car.
@alsharshani3 жыл бұрын
Not too long
@roaringlion42018 жыл бұрын
Doesnt sound like an ls1? Small block chevy yes but not ls1.
@Alsxg8 жыл бұрын
lmao what? that doesn't make any sense
@GearheadOutlaw8 жыл бұрын
ls1 is in fact a small block from Chevrolet 😛
@Alsxg8 жыл бұрын
Exactly lol
@roaringlion42018 жыл бұрын
+Outlaw No shit sherlock. What i mean is..is it a alum block? iron block? forged? bored? ofcourse its a gm small block. There is a difference between an ls motor and a general small block.
@roaringlion42018 жыл бұрын
+Outlaw What did he do to it then?
@jdayberry110 жыл бұрын
Time said 11 at the end...?
@bnastystuntz7 жыл бұрын
im callin bs on this one.. running this time with just cam and 250shot.. nah not happening specially wit them 853 heads.
@VegasRT5005 жыл бұрын
Yep I agree there is alot more performance parts in it.
@smithperformanceracing58485 жыл бұрын
Different brand but close to same cubes, my brothers 321 stroker, flat top pistons in full weight mustang on 250 shot went almost High nines in quarter Mile. He has suspension also
@bnastystuntz5 жыл бұрын
Charles henson read the description dipshit. it says stock 853 heads... Click the down arrow before u open ur mouth and look like the idiot ...
@MsJohnboy305 жыл бұрын
it possible I have a ls1 sat up almost the same way 💪🏿💪🏿
@hoost30565 жыл бұрын
It's legit. The whole car is dialed in well. When people know what they are doing, the stock stuff can get it done.
@jasonjones43399 жыл бұрын
Dont believe stock bottom end. Ls3 just went 9.35 with stock bottom end and they said it was the fastest in the world
@dfinkie10 жыл бұрын
It seemed like he left the line about 1 sec after the green.
@roaringlion42018 жыл бұрын
why?
@VegasRT5005 жыл бұрын
Definitely not a stock bottom end once you put ARP rod bolts in it.
@shitbox822 жыл бұрын
Yep, rod bolts = race engine. 😄
@VegasRT5002 жыл бұрын
@@shitbox82 LOL! I never said anything about race engine. That engine never came with ARP rod bolts from the factory so it is NOT stock. But since you are making stupid statements. When you install rod bolts usually the rod ends need to be re-sized which involves machine work but I doubt you knew that. I could install a Procharger on a stock engine with ZERO modification internally but still stock engine though. LOL!
@shitbox822 жыл бұрын
@@VegasRT500 Wow so much anger. 😄 I know plenty about reconditioning stock rods, enough to know that stock LS rods are reconditioned differently than SB or BB rods due to the cracked cap, that being said I didn’t use stock rods in the LS engines I’ve built, 4340 forged rods with ARP 2000 bolts in my 370” LQ4, with Wiseco 2618 pistons. I love the stock bottom end debate, always a touchy subject. 😄
@VegasRT5002 жыл бұрын
@@shitbox82 I get a little excited at times. Have a good day!