LT50 KFX 50 or quad master wont start fixed

No video

LT50 KFX 50 or quad master wont start fixed

Рет қаралды 17,207

Күн бұрын

Suzuki 50 is same as kfx50. 120psi compression, clean carb, exhaust is clear, wont start...crank seal popped out on magneto side. quick video to save you time diagnosing

Пікірлер: 28

@user-ge9dc2hh2m Жыл бұрын

Thank you this was exactly what was wrong with ours I would have never figured it out without this video thank you again

@dtmxing Жыл бұрын

So glad it helped! Thank the Lord as I just want people to save money and stress

@stephanienero5344 4 ай бұрын

Great video got my quad going again same issue😅

@dtmxing 4 ай бұрын

Thank you! Please subscribe and Lord bless you

@JohnDillenger-dy7tw 22 күн бұрын

Thank you for sharing your knowledge .

@MarkMallen-vo8hn 10 ай бұрын

Thank you for doing this video. It was the exact problem that I had. It started on the first pull after reassembly. Rotator cuff surgery next week to repair the damage from pulling it over a million times first. 🙄

@dtmxing 10 ай бұрын

You’re welcome and Lord bless you! I’ll pray for healing! Rotator cuff tear is no joke

@daltonwalters558 Жыл бұрын

This is exactly what I think is wrong with mine thank you

@user-kq6um1xr4x Жыл бұрын

Cheers legend! I've been scratching my head as to why this lil prick wouldn't start

@dtmxing Жыл бұрын

That’s great brother !!! God bless you and your family

@andersgunnarsson8113 Жыл бұрын

Thank you, had exactly the same problem on a lt50 suzuki. Seems to be common problem. Easy fix!!

@josh6346 Жыл бұрын

That was it, thank you, all day out here wondering

@robin88ohman 5 ай бұрын

thanks for this video that was exactly what was wrong with my son's quad. If it hadn't been for this video, I would still be sleepless😅

@dannylimbert9181 Ай бұрын

Hi how do u just push new one back on?

@maibalzich7602 4 ай бұрын

I wonder if this is whats happening to mine, has a fresh plug, fresh gas, spark, clean carb i even tried rejetting it a few times and only once did i get it to run for about a min with the choke on but then it would die.

@jwjb9918 Жыл бұрын

yes i think so same as mine

@berttstreasures3995 9 ай бұрын

Do I need to take the pull start cup off or just yank the flywheels one unit?

@mikesear5374 Жыл бұрын

Is there a seal on the other side also?

@dtmxing Жыл бұрын

Yes but same as transmission fluid side. It’ll suck trans fluid and burn the smoke if that side went out. Not typical for that side to have an issue

@mountainmatters6402 Жыл бұрын

I'm getting 30 psi compression at the plug hole. Think it could still be the crank seal??

@dtmxing Жыл бұрын

No you have worn our rings or cylinder and pistons scored making low compression you need to rebuild top end. Check rod ends while rebuilding. Check for play on big or lower rod end so you don’t put a new top end on and then have a worn out crank but I’ve never seen a crank go bad on one yet…plenty of bad top ends

@joelnewby8749 3 ай бұрын

Mine had smoke coming out near the carb after pull start rebuild. Won’t start unless exhaust is removed and will only run on start spray. I have spark and compression and fresh rebuild carb. Any ideas?

@dtmxing 3 ай бұрын

Exhaust is plugged with carbon