Mach3 Rotary Axis configuration

Рет қаралды 30,399

Күн бұрын

On this video tutorial, originally posted in Spanish; is intended to show how I configured the rotary axis on my CNC router, perhaps will serve as a guide on a similar situation for somebody looking for information on this subject, I am not an expert by any means all the steps that I use in this video I learned online and by trial and error. I start by showing how I calculated the gear ratio, followed by calculating the steps per degree for the main shaft gear

Пікірлер: 43

@mikruson 4 жыл бұрын

Awesome tutorial Carlos,thank you very much!

@CarlosMDominguez 4 жыл бұрын

Glad you liked it!

@laszlosoproni761 2 жыл бұрын

Thank you sir, Your video helped to setup my rotary axis. Just perfect explanation. You are legend.

@CarlosMDominguez 2 жыл бұрын

You are very welcome, thanks for your comment.

@djamelweld1059 8 ай бұрын

You are the best at explaining, thanks 👏

@CarlosMDominguez 8 ай бұрын

Glad you think so! Thank you for watching!

@pauldiaz4273 3 жыл бұрын

Great explanation thanks señor carlos!

@CarlosMDominguez 3 жыл бұрын

You are welcome!

@frankmardey2354 3 жыл бұрын

Thanx for this explanation. Very usefull

@CarlosMDominguez 3 жыл бұрын

Glad it was helpful!

@nikoanggriawan303 Жыл бұрын

Perfect explanation..❤ thanks a lot

@CarlosMDominguez Жыл бұрын

You're welcome 😊Glad you liked it!

@josiascnc4539 3 жыл бұрын

Excelente vídeo...

@CarlosMDominguez 3 жыл бұрын

Gracias!

@Mewanrahnam575 3 жыл бұрын

Thankyou..keep going Sir.

@CarlosMDominguez 3 жыл бұрын

Always welcome

@mecanizadosgrela7380 5 күн бұрын

Thanks for the video

@CarlosMDominguez 5 күн бұрын

@@mecanizadosgrela7380 your welcome

@umargul5644 4 жыл бұрын

Great job thanks sir

@CarlosMDominguez 4 жыл бұрын

Most welcome, thanks for watching!!!

@owenroque3633 4 жыл бұрын

thanks for the info

@CarlosMDominguez 4 жыл бұрын

Any time

@ambujsenapati3597 4 жыл бұрын

Thank you, sir. It's very helpful , if a program info about rotary ATC settings with mach3 .

@CarlosMDominguez 4 жыл бұрын

Thank you!

@hosseindten2457 Жыл бұрын

thank u thank u thank u So Perfect

@CarlosMDominguez Жыл бұрын

You're welcome 😊

@nick-k7k 4 жыл бұрын

Hello, I'm new to mach software. On the screen, it is showed only a 4th axis (only one rotary) but I found in many forums that it can support also the 5th axis. Please help me to understand If you can use the mach3 board for 5 axes and with which software

@CarlosMDominguez 4 жыл бұрын

I am not very knowledgeable on more than 4 axis machining, however yes you can use 5 or more axis with Mach3 providing that you have a control board , to design and generate the g-code you can probably use a program like Fusion 360, or similar. Good luck.

@hinrigardehes3253 3 жыл бұрын

Hello, can I make a digital machine without connecting the RS 232 cable from the driver to the computer with the mach3

@CarlosMDominguez 3 жыл бұрын

Mach 3 is a parallel interphase, but you could buy a parallel to USB adaptor I imagine if your controller is USB, I never used anything other than 25 pin cable though. Good luck.

@bocus9001 Жыл бұрын

thanks so much sir, please can you help me i installed rotary axis in pins of y axis as my machine setup design is using x- axis , z-axis, y axis as rotary axis and a-axis is tilting spindle head as i have mach3 4 axis not 5. how can i program it or using a definite postprocess which suits my machine design? i'm using powermill

@CarlosMDominguez Жыл бұрын

I am not familiar with Autodesk software, so I don't think I can figure out a post processor for it. Sorry I can't be of much help, (other than what I explained on the video). Thanks for the comment and good luck.

@brayanestevensfrancopereir5270 3 жыл бұрын

If my controller does not have micro steps, how would the formula be, my machine control it with a richauto a11 ??? what should i do to be able to calibrate the 4th axis

@CarlosMDominguez 3 жыл бұрын

You are going to have to search for specific information about your controller, maybe some KZfaq videos on the Richauto a11, seems that this controller uses its own controlling software independent of the computer, I am not familiar with it. So, I'm sorry I ca not help you with it. Good luck!