That and he started it on the work, then almost banged it straight back down. No wonder that bit needed sharpening, probably does again.

My first thought also. It didn’t cut at all well as a sharp drill would have two curly strands of swarf coming up. Bit shit

Thank you for information!

Help, I appreciate your comment because the angle grinder method was my first choice. I have three different wheels in my shop. One is the pieces of sand paper which you would eliminate as a choice. The other two are conventional hard grinding wheels. Can you recommend a wheel hardness? It is obvious you have some experience, so thank you for the help. cr

Chris Reeves 1 second ago Help, I appreciate your comment because the angle grinder method was my first choice. I have three different wheels in my shop. One is the pieces of sand paper which you would eliminate as a choice. The other two are conventional hard grinding wheels. Can you recommend a wheel hardness? It is obvious you have some experience, so thank you for the help. cr

Thanks for the advice. This device of my friend, from gave me a little play with it. I have already made a similar analogue, and a little understood the essence. Thanks again!

I've had that jig so many years and never used it. Cannot find the instructions for really setting it up proper now. Never took the time to buy a side grinding wheel for any of my bench grinders.

Also it's a large diameter to be drilling with no split point and no pilot hole.

How far should the bit extend past the index? Was this his mistake? Thank you for the help. cr

@@chrisreeves8037 Chris, the extension of the drill bit past the index (called the lip rest) should be half the diameter of the drill if grinding a point angle of 59 degrees. It is called Overhang and instructions are online for this under the name Craftsman Drill Grinding Attachment Model 9-6677. Most drills for general use will use 59 degrees. So, if this was a 1/2 inch drill bit, the overhang would be 1/4 inch past the lip rest. The lip rest is adjustable and should be extended slightly into the flute of the drill bit. The base of this unit and the pivot rod are angled to automatically set the clearance angle of the drill point during rotation or "sweeping" of the fixture. The overhang will vary from 1/16 of an inch for a point angle of 88 degrees to 100 percent of the drill diameter at a point angle of 49 degrees. This fixture will grind the point angle and the clearance angle at the same time.There is a point angle/overhang chart in the instructions.

It goes on the cutting edge.

Grinders typically have threaded female slots on either side to support the handle. You can see her he used the side without the handle to connect tú the bracket. Hope this helps! Blessings 👐 💚

@@sourceofuniversallove1449 Got it! Thanks so much.

Tem como vc mandar o lik da ferramenta

Comprou aonde ?

Перемычка не подточена, вот и сверлит тяжело.

Good one!

@@MadeInGarage mine is a picador Fig. 9 made in england simalar in every way expect for a spring loaded clamp to keep pressure off drill when loosening.

i know im randomly asking but does anybody know of a trick to log back into an Instagram account?? I was dumb lost my password. I would love any assistance you can offer me.

@Johnny Bowen Instablaster =)

@Karter Marcus Thanks for your reply. I got to the site on google and I'm trying it out atm. Looks like it's gonna take a while so I will get back to you later with my results.

@Karter Marcus It worked and I finally got access to my account again. Im so happy! Thanks so much you saved my ass :D

@Johnny Bowen Glad I could help :D

I think the issue was the ineptitude of the operator

Care to elaborate?

I grind where I please

Hi. My friend bought it at a flea market

На ебее есть, тот что в ролике раритет, или аналог купить

Не рабочее. Задняя кромка подгорела.

@@Bastyon.при таком методе заточки нет затыловки

OK

🙄

Did you watch the video that you commented on? I agree that the video showcases some GAWD AWFUL practices, but certainly not the one you're talking about. If you want to spout some anti-china BS, do it somewhere else.

I will do it where I want and when I want.@@Zach-st4um