Main Rotor helikopter EXPERIMENTAL HELICOPTER BUILD Aluminum 6061-7075

Рет қаралды 60,026

2 жыл бұрын

Main rotor head 16mm 7075
Right and left side 30mm 7075
Pitch Horn roudbar dia 76mm 6061
.
.
.
.
.
.
.
#Rotorhelikoter
#caramerakithelikopter
#caramembuatdrone
#mesinhelikopter
#mainrotorheadexperimentalhelicopter build series
#EXPERIMENTALHELICOPTERBUILD
#carakerjahelikopter
#balingbalinghelikoter
#pesawathelikopter
#helikoterexperimen
#experiental

Пікірлер: 45

@sigitwidjaya4950 2 жыл бұрын

Mantap bang Thomas. Tlng video nya dilanjutkan sampai swashplate nya bang. Dan tes momen keseimbangan laju geraknya juga . Inspiratif. 👍🙏.

@Bintangofficial646 Жыл бұрын

Keren sukses selalu 🙏👍👍

@arsyadtech 2 жыл бұрын

Good job. Jadi pingin ngelihatnya

@ShafiqulIslam-fp5dx 2 жыл бұрын

I am looking forward to seeing you next video soon.

@sunardi776 Жыл бұрын

Mantul bang,,

@herlih3934 2 жыл бұрын

Kren nih. Subrek ahhh 😃

@coalitionofarttechnologycl9063 Жыл бұрын

Your use of Hacksaw Blade & Frame in cutting is tidious. In this modern era, you can use Jigsaw Machine, Angle Grinder to make your work easier

@rahulchoure8035 Жыл бұрын

Very good gob

@ArtorMachine 2 жыл бұрын

Wihh keren! Harus jadi ini. Siap supply mesin nanti

@Thomas_Creative 2 жыл бұрын

Bikin Head mesin 2tak bisa ga mas 😁

@dul1720 Жыл бұрын

Bikin vidio perakitan helinya bang

@user-fk2wi6dr9z Жыл бұрын

😄😄😄👍👍👍

@johntenhave1 Жыл бұрын

Please blend those scribed scratches out of the side plates. The alloy you are using is terribly intolerant of fatigue and you have just scratched a a whole load of stress risers into one of the most heavily stressed parts of the airframe. it will kill you if you do not repair it.

@ralphjann 11 ай бұрын

Is this a purchased plan or your personal design?

@Mehmet__ 2 жыл бұрын

bro, is the material you use steel?

@cloudusterable 2 жыл бұрын

Have you just got one bearing on each fork ?

@denilsonbatista184 Жыл бұрын

@Ben-Dixey 2 жыл бұрын

Looking good 👍

@Thomas_Creative 2 жыл бұрын

Hello helicopter youtubers, how about your project ?

@Ben-Dixey 2 жыл бұрын

Thomas Creator my project is going well thanks, I have tested the rotors to full rpm and full throttle and the helicopter nearly lifted itself but would not lift me as well. My gearing is too high at 5.6:1 I'm going to change the gearing to 7:1 and see what happens then. The empty weight is 118kg so with 60hp I think it should be possible. The tip speed I'm now aiming for is 515ft/sec, I believe this should be somewhere near. What's next on your project? the engineering looks good, looks like you have chosen thick enough materials to take the centrifugal loads. 👍

@Thomas_Creative 2 жыл бұрын

@@Ben-Dixey it's the same, hopefully my project will also go well, I chose a thick material to make it even stronger he he he,

@Ben-Dixey 2 жыл бұрын

@Thomas Creator going thicker than you think you will need is good as far as safety but also adds weight. You can work out the centrifugal forces from the blade weight and centre of mass. Then you can use the cross sectional area to calculate the of tensile strength of the parts. What you have done looks good but if you can check the numbers it will give you confidence in your machine.

@masimart224 2 жыл бұрын

Sudah jadi om helinya..pingin bikin juga.. 🙏