Make a POWERFUL Stun Gun for Self Defense

Make a POWERFUL Stun Gun for Self Defense | DIY

Рет қаралды 309,746

Күн бұрын

Hey guys! This time, we make a powerful little pocket-sized rechargeable Stun Gun (Taser).
This is Version II of my Stun Gun, packed down to a cylindrical body, safer contact probes (Not sharp & pointy), easy to recharge now via Micro USB, and a brighter power indicator light for better day-time power indication.
The Stun Gun we make in this video shall not be wrongly used, this is only a self-defense tool and must be used for that purpose only. Do not try it on yourself, animals or any other people just for the "Sake of it".
If you enjoyed watching this video or found it informative, please consider leaving a thumbs up, share, comment, and subscription to the channel! :)
----------------------------------------------------------------------
👉 Visit my online Storefront: sites.google.com/view/maximag...
----------------------------------------------------------------------
☕ Buy me a coffee: www.buymeacoffee.com/MaxImagi...
----------------------------------------------------------------------
Instagram: @max.imagination - max.imagina...
Instructables page: www.instructables.com/member/...
----------------------------------------------------------------------
Disclaimer: Amazon purchase links below are affiliate links. It doesn't cost you extra to buy through those and I just get a tiny commission. Thank you!
Download the Stun Gun's circuit diagram here:
drive.google.com/file/d/1jNHU...
--------------------------------------------------------------------------------
Materials/Parts & Tools needed for this project:
High-Voltage Pulse Generator Module - amzn.to/3Gf3gmu
18650 3.7V Li-Ion Battery (2200mAh) - amzn.to/3tozB6W
TP4056 1-cell 4.2V MicroUSB/USB-C Charging board - amzn.to/3Eo1Jdq / amzn.to/3T4pQli
SPST 2-pin On/Off Switch - amzn.to/3SK3JAO
Pushbutton with cap - amzn.to/3MdaB7u
5mm Red LED - amzn.to/3Meds07
49-56 Ohm Resistor (1/4W) - amzn.to/3CFaeiS
(x2) Probes (Get yours from AC power plugs)
Heat-shrink wrap tubes for electrical wires
Insulated electrical wire - amzn.to/3SHow89
3/4-Inch electrical PVC tube
2-solution based Epoxy - amzn.to/3V8FgHa
Masking tape
Spray paint
🪛🔧🔨 Tools and extra supplies I use:
➡️ Soldering Iron Kit - amzn.to/3X6L5Wq
➡️ Hot Glue Gun - amzn.to/3E6trJG
➡️ Drill Machine - amzn.to/3EDe0u8
➡️ Box cutter/Utility knife - amzn.to/3hP9MGI
➡️ X-Acto Hobby Knife - amzn.to/3XbL7ML
➡️ Cutting Matt (Green) - amzn.to/3gil71A
➡️ Needle-nose Pliers - amzn.to/3ECTKc3
➡️ Wire Cutters for Electronics - amzn.to/3ECut1B
➡️ Wire-stripping tool (Automatic) - amzn.to/3hQsMVD
➡️ Screwdriver kit - amzn.to/3V6vgNX
➡️ Heat-shrink Tube Kit - amzn.to/3AksTPE
➡️ Jumper Wire Kit - amzn.to/3UGhMZq
➡️ Breadboard for Prototyping - amzn.to/3GlF4ze
➡️ Perf Boards, Pin headers, and Connectors Kit - amzn.to/3AkySUw
➡️ Superglue - amzn.to/3EE6uis
➡️ Duct Tape - amzn.to/3g5mTU0
➡️ Double-sided Tape - amzn.to/3Edta82
➡️ Kapton Tape (for battery leads) - amzn.to/3X58bNl
Music credits:
Ma Jolie - YT Audio Library
Song: ELKAA - Ocean
Video's Link: • ELKAA - Ocean [Free Ch...
Mission Start - YT Audio Library
Song: Hinrik. - Babylon ft. Xyche
Video's Link: • Hinrik. - Babylon ft. ...
Chase - YT Audio Library
#stungun #electronicsdiy #maximagination

Пікірлер: 349

@TNT-km2eg 8 ай бұрын

Most people are stunned when they find out how bad electrician I am

@russfunk7615 6 ай бұрын

I noticed you used the black epoxy I know as J-B WELD Or J-B KWIK. If this is the case then your electrical short at the terminal base is the epoxy. J-B epoxy has metal filings in it, so the voltage output will travel through it.

@funtageHQ 4 ай бұрын

The problem is in Australia where It is illegal to defend yourself with any kind of weapon even with a permit. Doesn’t work too well when you have people running through houses and attacking people with weapons just for fun. Screw the government and screw the system. I have a god given right to protect myself and my family and I will exercise it where necessary. Thankyou for the information Naturally I take full responsibility for any legal ramifications from building one of these and using it if I choose to. God speed my friend. You are a hero

@MaxImagination 4 ай бұрын

Restrictions suck. I am glad my video helped you. Stay safe! Cheers.

@Technocrafts 2 жыл бұрын

This is so amazing project! Loved it 😍

@MaxImagination 2 жыл бұрын

Thank you so much! 😃😍

@curiosity7357 7 ай бұрын

Hi technocrafts!

@erikrodriguez6327 Жыл бұрын

Nicely done man! I made one a few years back and all I did was hot glue the transformer and battery holder together and put a US to EU power adapter on top for the prongs lol. Yours is a lot more detailed. 👍 BTW I love how you called out how it does NOT output the claimed 400000 Volts, a lot of other KZfaqrs fall for the false advertising. Great job man

@MaxImagination Жыл бұрын

Thank you for your comment, Erik! Haha, you made your's the crude way, pretty cool! Yes, many fall for believing a little module can deliver a voltage so high where it really outputs a several hundred to a few thousand volts at a minuscule level of current. Cheers!

@DaSlotho Жыл бұрын

heres mine that i made kzfaq.info/get/bejne/bJ2cbK-HyK-1aWQ.html

@kavindulakshitha9732 2 жыл бұрын

Wow. Nice stun gun. Good job max 👌👌👌

@MaxImagination 2 жыл бұрын

Thanks a lot! 😊

@liamb7268 Ай бұрын

I want to learn more about electrical systems and this really helps! hoping to make a calculator from scratch soon.

@philippe1384 Жыл бұрын

The starting scene looked like an ad for a vape pen or something

@jasoncooke5741 8 ай бұрын

Nice work, I love the design I was going to just do a basic one and try 3d print something but the pvc pipe idea looks great think I will try copy your design.

@MaxImagination 8 ай бұрын

PVC seemed cheap and effective at the time, worked well too! Save on some filament and have a sturdier design 👍 Cheers!

@BuildCreation 2 жыл бұрын

Awesome Work dude!

@MaxImagination 2 жыл бұрын

Thanks, bro! :D

@mari71c0 4 ай бұрын

Very good video very informative **Borat voice** "I like you"

@tiagodesteffani 2 жыл бұрын

Awesome, Max 👏🏼👏🏼👏🏼👏🏼👏🏼

@MaxImagination 2 жыл бұрын

Thanks, Tiago! 😊

@spmrgamer9320 11 ай бұрын

that is like, so fire 🔥🔥🔥

@alishchapagai3599 2 жыл бұрын

So Amazing Max 👏 😍

@MaxImagination 2 жыл бұрын

Thank you, Alish! 😊

@kspcreation666 2 жыл бұрын

Amazing and so cool 🔥🔥

@MaxImagination 2 жыл бұрын

Thanks, brother! 😍😃

@GrandadsOtherChannel 2 жыл бұрын

Interesting project Max 👍⚡

@MaxImagination 2 жыл бұрын

Thank you! Cheers!

@jaimedelgado7529 5 ай бұрын

@@MaxImaginationbro...1 to 10 how much does this hurt ? Is it enough to discourage an attacker or will it piss him off even more ?

@vishalsxperiments4488 2 жыл бұрын

Hello Max! What an amazing project! I'm wondering if I can use a 4v Lead-acid battery(as I have one). Is that fine?

@MaxImagination 2 жыл бұрын

Hello Vishal. Thanks for watching! Sure, a 4V battery will do, anything from 3.7-6V is totally cool to use with the Stun gun module. Cheers, Max

@user-jf7ds7rv8r Жыл бұрын

@@MaxImagination 😂

@marvalworld5582 4 ай бұрын

But does we can use charging module of lead acid battery

@train4905 2 жыл бұрын

Brilliant,nice one

@MaxImagination 2 жыл бұрын

Thank you! Cheers!

@Mr.GeniusCreation 2 жыл бұрын

Nice one bro 👍

@MaxImagination 2 жыл бұрын

Thanks, Sahil 😊

@DoItYourself-DIY 2 жыл бұрын

Good stun gun, Max

@MaxImagination 2 жыл бұрын

Thanks! =)

@astr0yt344 2 жыл бұрын

Yasss I was waiting for you to post

@MaxImagination 2 жыл бұрын

Thanks for watching ☺

@gamatester1732 2 жыл бұрын

Gonna use it later

@sidsolocreation 2 жыл бұрын

Awesome broooooooo Your my brother from another mother

@MaxImagination 2 жыл бұрын

Thanks, Sid! :D

@BangboSeries-hl6je 2 ай бұрын

Stunning..good 💡

@MaxImagination 2 ай бұрын

Thank you! 😊

@BangboSeries-hl6je 2 ай бұрын

@@MaxImagination welcome brother..👍🙂

@SC.243k 2 жыл бұрын

Very nice 👍

@MaxImagination 2 жыл бұрын

Thank you 👍

@janschultz6047 7 ай бұрын

Very nice!

@MaxImagination 7 ай бұрын

Thank you! Cheers!

@7MinutesCreative 2 жыл бұрын

Haha Awesome stun gun Max ❤

@MaxImagination 2 жыл бұрын

Thank you for your support, buddy! 😃

@7MinutesCreative 2 жыл бұрын

@@MaxImagination You're welcome dude 👍

@slyasastech 2 жыл бұрын

@@7MinutesCreative Hello

@7MinutesCreative 2 жыл бұрын

@@slyasastech Hi

@TheGripsion 2 жыл бұрын

So cool!!!

@MaxImagination 2 жыл бұрын

🙌✌

@Yincha1 2 жыл бұрын

i had this same idea but i want to do it with a vape mod box that takes 2 of those batterys

@creative_thinker 2 жыл бұрын

Superb 🙌

@MaxImagination 2 жыл бұрын

Thank you! 🤜🤛☺

@stater3 Жыл бұрын

Discovered that if you connect the module (load) to the OUT + and Out - on the charging board, the firing will not work very well. I noticed you connect the module in parallel with the battery B+ and B- on the board.

@MaxImagination Жыл бұрын

Thanks for noting this!

@lucasmertens1 Жыл бұрын

Hey Max, I’m just a little curious about something… I see in both your video and your schematic you place the rest of the circuit in parallel with the battery terminals, rather than using the outputs on the TP4056 board itself. Was there a specific reason you chose to do that?

@MaxImagination Жыл бұрын

Hi there, Lucas. Interesting you point this out... I have done this to bypass the charging board's over-discharge protection feature that comes with when connecting the circuit to the OUT+ OUT- terminals. Another viewer found that connecting the rest of the circuit with the OUT terminals resulted in very early circuit cutoff, reducing the stun gun's reliability when one really needs it. Implementing something such as one of those cheap battery voltage level indicators into the side of the stun gun can come in handy, knowing when to recharge the battery. Hope this makes sense. Be sure to choose wisely on which terminals you connect the circuit to. As recommended and shown - hooking the circuit up to the same battery terminals of the board will ensure more reliable performance. Cheers, Max

@netanelcohen4630 2 жыл бұрын

Grate vid my friend. BTW, can you tell me where can i find a source of information in more detail about the operation of the transformer and how exactly it works? thank you!

@MaxImagination 2 жыл бұрын

Hi. Thank you! So far, I couldn't fink any specific sites which go into detail about how this Stun Gun's type of module works, though you could check out this site of information about the general practicality of how one works and about the danger - www.tbotech.com/stun-gun.htm However, I did find this video from DiodeGoneWild explaining the working principle behind the Pulsating High voltage transformer - kzfaq.info/get/bejne/lcCja9Gg3Zq1n3U.html You may also find this helpful - www.hindawi.com/journals/jece/2020/6525483/ Cheers, Max

@netanelcohen4630 2 жыл бұрын

@@MaxImagination Thank you very much!

@user-ws9ci1lf3o 2 жыл бұрын

Would probes from a 125 volt power plug work or does it have to be 220 volts? All the 220 volt power plugs I've found are super expensive while the 125 power plugs aren't.

@MaxImagination 2 жыл бұрын

HI, a 125 volt probe pair should work just fine, I mainly chose the 220V type probes because of their shape. So, no worries on that one! :)

@CarPea 2 жыл бұрын

Made the first one and will make this one

@MaxImagination 2 жыл бұрын

So cool to hear! 😍

@pandelistcouxnikas3704 Жыл бұрын

i make this this is amazing

@CraftChannelYT 2 жыл бұрын

Nice video bro 🙋‍♂️

@MaxImagination 2 жыл бұрын

Thanks! 😊

@jamesdoehler9870 Жыл бұрын

Cool 😎👍 better to make your own then the ones in the store .. they're all cheap .. I don't know why it's so hard to find a well made product these days 🤔

@MaxImagination Жыл бұрын

Thanks for watching! Yup, DIY is often the way to go!

@Lbm414.Oleg.Kuznetsov. 7 ай бұрын

China ! 🇨🇳 =💩

@shrexzan 6 ай бұрын

Can you make Taser Ring ???

@handyman683 11 ай бұрын

This is wicked 😂

@lee16586 4 ай бұрын

would like to ask the output wires is it both positive or negative ? is it possible to connect 2 pulse generator?

@MaxImagination 4 ай бұрын

They do in fact have polarity as it is amplified DC voltage! This video shows two connected in series for a bigger zap: kzfaq.info/get/bejne/oJ54g9Nhlpyrf6M.html

@wiwibaguette6683 Жыл бұрын

hey man i have a question, shouldnt the wires on the transformer go on somewhere else on the smart chargingboard instead of soldering directly with the battery wires?

@MaxImagination Жыл бұрын

Hey there! The input wires of the transformer don't go "directly" to the battery, but through a switch and a push button, yes.

@wiwibaguette6683 Жыл бұрын

@@MaxImagination ohhh ok I get it now

@dvnoytekvlog6634 Жыл бұрын

Nice..

@slyasastech 2 жыл бұрын

Nice

@jaydeegirard9673 2 жыл бұрын

I wanna make one from a flashlight but I was wondering if I can use metal as material like a old Maglite flashlight or the case must be plastic.

@cdunne1620 Жыл бұрын

I would use plastic mate, with high voltages come the arcing phenomena where a pathway through the air is taken by the current in jumping to a conducting material (metal), respectfully Max’s advice here is not the best

@jaydeegirard9673 Жыл бұрын

Thanks y'all for the answers

@francescogallo1013 9 ай бұрын

Hi! Awesome build buddy, just a quick question, is it going to be lethal if used on an arm / leg (far from heart for instance)?

@MaxImagination 9 ай бұрын

Hi there. Thank you for your comment! It shouldn't be.

@francescogallo1013 9 ай бұрын

@@MaxImagination Thanks!

@MaxImagination 9 ай бұрын

@@francescogallo1013 No problem :)

@platoon1016 3 ай бұрын

bicycle handle bar grip with finger grooves would be cool and help orient hand position.

@MaxImagination 3 ай бұрын

Good tip!

@mccloudcodess1634 6 ай бұрын

Hello. I saw your video. I like that. Moe power bro. Love it Bro. it possible change capacitor more powerful to weak people specially those rubbers, snatcher. And much capacitor do I buy small capacitor but strong enough to weak or stop him.

@MaxImagination 6 ай бұрын

Hi there. Thanks for your comment! I don't know what you mean, sorry.

@user-od1jy3zo4e 20 күн бұрын

FIRST MAX THNK YOU FOR THE INFORMATION. .IS THWR ANYONE WHO REMEMBERS HOW MANY WINDING TO MAKE A PLAZMA ARC PULSE GENERATOR USING A 9 VOLT BATTERY AND SPARK PLUG I GET A ELECTRIC SHOCK BUT PULSE ARC AND USING A ULTRAISO CAPACITOR FOR THE PURPLE ULTRASONIC ARC

@MaxImagination 20 күн бұрын

No problem :) I have no idea about the number of windings in one of those. That would require more calculation... You can in fact order these high voltage arm modules for cheap. Cheers

@dndstories1377 Жыл бұрын

Hey Max, I was wondering where you got the probes because I couldn't find it. But I did find a ground prong that looks like the probe you have so, like do I buy a charger and remove the ground prong because I have no idea what else to do

@MaxImagination Жыл бұрын

Hi DnD, I already had these ground-probe looking probes already lying around in my electrical parts box, I wouldn't be too sure exactly where they came from. I'd say regular cable ground probes would do the job fine. I recommend you purchase a "TP4056" single-cell battery charging module for safe recharging of your DIY Stun gun, you can purchase these on online stores such as Amazon. Hope that helps! 😊 Cheers, Max

@dndstories1377 Жыл бұрын

@@MaxImagination okay thank you

@phylippusvonhohenheim3232 Жыл бұрын

Hello Max, new subscriber from brazil here, i have a ask for you, can you make an arc lighter using this project base? can you make an tutorial about it? here i live its very difficult and too expensive to find an arc lighter to buy, please do this

@MaxImagination Жыл бұрын

Hi there, yes it's possible with this Stun Gun module. The taser with a narrower gap between the electrodes can simply be used as an arc lighter as well. Simple as that! 😀 Thanks for subbing!

@AgentQQ8 Ай бұрын

Not bad. =)

@Viteasy 7 ай бұрын

Hello. I want to make one but more powerful. Would you advise me to put two of these modules or put one with more batteries?

@MaxImagination 7 ай бұрын

Hi there. I suggest you use two of these HV modules in parallel at the inputs with one battery pack of 7.4V. Cheers.

@dwightschrute2822 8 ай бұрын

Mine was not as nice as yours but at least it works. How long does the battery last for you? Thanks

@MaxImagination 7 ай бұрын

Nice to hear you recreated the project! Cool! My stun gun lasts me a few weeks (I don't stun it that much).

@quandaledingle9693 Жыл бұрын

Wanted to ask if the led of required, because buying a single led and resistor just doesn't seem worth the trouble

@MaxImagination Жыл бұрын

Hi there. It's not required at all, but it pays having one for peace of mind knowing when the stun gun is off. I'd recommend you salvage one of those 3 or 5mm LEDs from any old appliance. You will most likely find one. Cheers, Max.

@taylerrichards3534 Ай бұрын

hey when you use the button does it have the be square? Or can I get a circle one

@MaxImagination Ай бұрын

It can be any shape as long as the button you choose can handle the current.

@deloslanc7755 Жыл бұрын

ALWAYS DE- electtrictize capacitor’s ! ALWAYS have someone with electrical experience assist ALL projects if you don’t know COMPLETELY what you’re working with .

@deang5622 7 ай бұрын

The word is *discharge* not DE-electtrictize.

@tbip2001 8 ай бұрын

Is it possible to build this with a potentiometer so that the outout can be turned up and down?

@MaxImagination 7 ай бұрын

Possible... but you will need more than a potentiometer. I recommend you use a DC-DC converter at the input like the LM2596.

@user-ic9lu3lq6q 2 ай бұрын

Brother what if I use Power Bank Module T6845-C (5V Step-Up Power Module ) instead of Tp 4056?🤔

@MaxImagination 2 ай бұрын

That will work too. You can use it and also have it as a power bank combo.

@user-ic9lu3lq6q 2 ай бұрын

Thanks bro, for response, GOD bless you @@MaxImagination

@normanmacari1304 Жыл бұрын

I am looking forward to trying to make one but im not familiar with anything about physics but im going to give it a try i love these type of gadgets

@MaxImagination Жыл бұрын

Best of luck!

@snehadixit704 Жыл бұрын

hey! i was wondering can like how powerfull the stun gun is be changed like i m planning to make a prototype of the same and i dont want it very powerfull, is there any way to do that?

@MaxImagination Жыл бұрын

Hi there! You can use a weaker battery, such as a 3V one with the transformer to get a less powerful stun out of it.

@fearfultariff 10 ай бұрын

Can you please explain how this works because I have read that these transformers are only usable for ac input and not dc input provided by battery

@MaxImagination 10 ай бұрын

To put it simply, the high voltage pulsating transformer takes a low voltage DC input and produces a high voltage DC output thanks to a voltage multiplier circuit which uses a specifically timed sequence of capacitors that charge up and build on that voltage + diodes to direct that current to keep building up. Hard to explain, though I hope you get the main idea of how it works.

@fearfultariff 10 ай бұрын

@@MaxImagination yep and thanks for replying Most youtubers don't reply. Amazing video

@user-sn7yx5zr1d 5 ай бұрын

What if we use a bigger battery like a 7.4 volt would the power boost module be able to handle it?

@MaxImagination 5 ай бұрын

Most likely it will, but not for very long (unless otherwise specified) due to the internal circuitry in most of these failing often above an input of 6V.

@kristoffermulbjerg6848 2 жыл бұрын

very interesting

@MaxImagination 2 жыл бұрын

Thanks for watching!

@Peec187 Жыл бұрын

Will a 3.7V 18650 Battery work with a pulse generator with an Input voltage of 3.7V-7.4V ?

@MaxImagination Жыл бұрын

Yes, that battery should work.

@rafix0.13 3 ай бұрын

I dont know why the spark wont jump from probe to probe, i glued two small metal sticks on tope of each probes and it sort of helped but the spark doesent always jump, like i could click the button and i can hear something but no sparks. Any solution?

@MaxImagination 3 ай бұрын

Maybe your probes are closer somewhere below resulting in a muffled spark or the probes are too far away from each other. Best thing you can do is angle the tips and move them closer together with a narrower gap.

@kronikphase 7 ай бұрын

i use the board as a switch from a disposable vape. find where the actuator for the vape is and touch the contact s and boom touch button taser

@MaxImagination 7 ай бұрын

That's a much better use of that tech, nice!

@BollYogi 10 ай бұрын

Nicely done'dude 👍! One thing: there is no safety apparently so suppose you carry it in your pocket,you can SELF-FRY ,isn't ⚡🤪?

@MaxImagination 10 ай бұрын

Thanks! The switch at the bottom is the safety feature 👍

@matthewdavies9239 6 ай бұрын

The only thing I would change is that safety switch as it could easily be push me personally I used one of the switches that's got the clear rubber box over with the switch inside as these need a bit more pressure to switch between safe and armed but yeah get little project max keep post new vids champ, is there anyway you could make one with 3 batteries

@gamingzone7257 2 жыл бұрын

Your very intelligent I am from 🇮🇳india

@MaxImagination 2 жыл бұрын

I appreciate your kindness! Have a good week ✌😁

@IDemonstrateVelocity26 Жыл бұрын

Hey bro I have 2 questions Does a 6A switch work and can you show how to wire a switch with an integrated led

@MaxImagination Жыл бұрын

Hi there. 6A switch might be a bit overkill for this application, but I'll work. Are you referring to one of these? es.aliexpress.com/i/33003707517.html?gatewayAdapt=glo2esp

@taylerrichards3534 Ай бұрын

Hey man is this actually powerful? Like say if I’m attacked by someone and I stun them will it hurt

@MaxImagination Ай бұрын

Hey there. Yes, for some it may even get them on the ground.

@warkhi5741 Жыл бұрын

Hello, my battery is the 9900 mAh 18650. Will this cause harm to me if I attempt to touch it?

@MaxImagination Жыл бұрын

Hi there. If you power the high voltage module with a battery, it will hurt touching the wires on the other end.

@Peec187 Жыл бұрын

Hey, I wanted to do this by myselfe but I dont know wich cables I should use to extend the range of the LED (How thick etc. they should be) sorry i am new to physics and science stuff in general

@MaxImagination Жыл бұрын

Hey there! 32-Gauge insulated electrical wire would be the ideal choice for connecting an LED, anything thicker such as 24 or 20AWG, etc... will also work. Cheers.

@Peec187 Жыл бұрын

@@MaxImagination thank you fir your answer

@shadowmihaiu 7 ай бұрын

Nice. But voltage is just voltage. The actual effectiveness of a stun gun is measured in microcoulombs. Any idea how many microcoulombs this puts out?

@MaxImagination 7 ай бұрын

No idea. I wouldn't have a clue unless I review the project and measure that, somehow...

@electric_mix Жыл бұрын

Nice job 👏

@MaxImagination Жыл бұрын

Thanks! 😁

@aaronjorgevasquez6704 6 ай бұрын

hi its okay to use types c charging board

@MaxImagination 6 ай бұрын

Yes.

@crazyexperiments3179 8 ай бұрын

I also love to do different Projects just like you. I did other projects like RC cars, RC aeroplanes, water Tornado, etc. I would like to get in touch with you.

@MaxImagination 8 ай бұрын

Fantastic!

@Hemaram_Jangid 8 ай бұрын

Does it worka continuously. I also made one. But stops after few sparks

@MaxImagination 7 ай бұрын

I do not advise you run it continuously as that may overheat and damage the internal oscillating transistor.

@Hemaram_Jangid 7 ай бұрын

The problem has resolved. I connected directly with battery for output.

@iluminblox2420 Жыл бұрын

Does it have to be a 3,7v battery or can it be any rechargeable battery?

@MaxImagination Жыл бұрын

It can be any rechargeable battery up to 12V and no higher. Such as 1-cell, 2-cell, & 3-cell configured batteries. Cheers.

@mrkingalpha5538 Жыл бұрын

Wonderful

@mccloudcodess1634 6 ай бұрын

How powerful is that (taser)? And how does the body take that? Can you give all the materials bro. To buy

@MaxImagination 6 ай бұрын

Materials can be found linked in the video description.

@ferry2869 6 ай бұрын

what if I use 2 3,7v battery in series? or it should be in parallel?

@MaxImagination 6 ай бұрын

You can as long as your high voltage module is rated for up to 9V. Otherwise, I suggest you stick to running one with a parallel battery pack.

@user-yl7tn5mf9n 6 ай бұрын

Is it possible to get a list of materials and where to buy them?

@MaxImagination 6 ай бұрын

Check the links in the description.

@Kikutuca 7 ай бұрын

Awesome 👍. I made one exactly like yours, but it only works twice. The HV component stopped working. I did verified that the HV side open.

@MaxImagination 7 ай бұрын

Thank you! These cheap HV modules tend to be very sensitive to the input voltage supplied. Try to power your HV module not higher than 6V next time. Cheers.

@raysarobbani509 Жыл бұрын

Bro is there any chance of it blasting?Should we be careful while charging it?

@MaxImagination Жыл бұрын

The TP4056 (Lithium cell charging board) automatically stops the battery from overcharging. No need to worry about that.

@diegojauregui665 Жыл бұрын

can I use glue instead of epoxy to hold the probes?

@MaxImagination Жыл бұрын

Yup, depending on the glue, it should work.

@giuli1387 Жыл бұрын

Hey! What's the name of the device u showed in the intro next to the glue gun? This black pen looking thing

@MaxImagination Жыл бұрын

Hi there. I believe you're referring to my Soldering Iron 😄

@giuli1387 Жыл бұрын

@@MaxImagination I was, tysm

@joshuaaranguren1020 2 жыл бұрын

Looks like a bad shock for sure ⚡⚡⚡⚡

@MaxImagination 2 жыл бұрын

Oh yeah, a "shocking" one 🤣

@joshuaaranguren1020 2 жыл бұрын

@@MaxImagination 😂😂😂😂😂

@clarkfox7961 Жыл бұрын

Easy to do if you have all the parts , Shere fo you get them ?

@MaxImagination Жыл бұрын

Purchase links to the required parts can be found linked in the description below.

@lalitomensaje422 2 жыл бұрын

Does it charge by sun?

@MaxImagination 2 жыл бұрын

It can 😃 It can be charged with the DIY solar power bank I made in a previous video

@brianperry9517 8 ай бұрын

Hi what is best voltage battery to use thanks

@MaxImagination 8 ай бұрын

Hi. Use a battery between 3-9V. This may vary from transformer to transformer...

@hackmedia7755 3 ай бұрын

you could 3d print a case, it's a lot easier and will look more professional. Anyway nice job.

@MaxImagination 3 ай бұрын

Didn't have a 3D printer at the time. Nowadays I would make one 3D printed. Thanks for your comment

@tarsiousmunalembohol 2 жыл бұрын

Hey max. How to solve the issue of draining the battery?My project drains battery real quick just 5 clicks battery is drained.

@MaxImagination 2 жыл бұрын

Hi, Tarsious. Hmm, that could be due to you using a weak battery on its last legs. Are you using an old battery? What are the battery's specifications?

@tarsiousmunalembohol 2 жыл бұрын

@@MaxImagination new but cheap baterries. P

@MaxImagination 2 жыл бұрын

@@tarsiousmunalembohol Normally, a battery would last pretty long when used with a stun gun module, that must mean you have really weak batteries. I suggest you try another 3.7V one. Cheers, Max

@ADesertHat 24 күн бұрын

I'm using this primarily for self-defense. Is this lethal? If so I want to avoid that.

@MaxImagination 23 күн бұрын

It's not lethal at this level, but it can take someone down to the ground.

@merakisiva1183 8 ай бұрын

can I have a list of what materials did u use

@MaxImagination 7 ай бұрын

Please check the description box below.

@MrWoody17309 Жыл бұрын

my battery is getting hot. Am I using wire that is too thin. Its the only thing you didnt list in your list of items to be used.

@MaxImagination Жыл бұрын

Hi, Nick. I recommend you use 24 AWG enameled wire. If your battery still overheats then, I suggest you would need to replace it for another battery. Cheers.

@pennjones-evans8448 2 жыл бұрын

is this safe to use on a person, how much would it hurt?

@MaxImagination 2 жыл бұрын

It made me fall to the ground when I accidentally shocked myself. So on average, it would either make you fall or nearly to the point of falling in shock. The shocks hurt quite a bit, like getting shocked by a 120VAC power outlet.