If you wait to cut the slits until after you stick everything together you won't have to worry about the slits not lining up. Makes things easier. And, if you're concerned about the staples, you could cut two vertical slits the same length as the width of the Velcro strap and just thread the strap through those slits.

Great video. Here are some tips to make the assembly even easier: I built my large diffuser by first making the three part composite using the 9X12 size of the foam piece. I only needed one copy of the template, which I placed over the rectangular 9X12 composite, and made the cuts with scissors. Another modification: instead of the black foam on top, I used black felt (also from the crafts store, 9X12). The felt does not have an adhesive backing, so I used spray adhesive for that. Why felt? Because it is essentially the same as the "soft" side of the Velcro strips! This way, to attach the Velcro loop that goes around the speed light head, I just placed it hard side down on the felt, it sticks very well. No need to staple it. At the other end, I put the hard Velcro strips on the flap, and they stick to the felt very nicely when I fold the flap, as in the instructions.

This looks more durable than some of the diffusers that I’ve seen on amazon. Thank you for sharing!!

First of all, thanks for your video! I came up with a dramatically easier design that might be as good. Instead of using three layers of materials, canvas, black and white foam, you can just use one, plus some tape to make it reflective and light-tight. Starting with your template, I used a mylar sheet of the type used as stencil. In my case was however a cannibalized plastic folder. A clear plastic place-mat is also good. This material is quite rigid, so instead of curves, you may have to resort to sharp angles to achieve the final form. This is done by making a cut with a knife, not too deep, and carefully bending the sheet trying not to break it. You could lose some material before you gat it right. To fix the overlapping parts you have to use stables, so in the end you cannot store it flat. The whole thing is however quite robust, you can just put your flash in the diffuser and then both in the camera bag. The material is translucent, so how to make it reflective and light-tight? For that I used aluminum adhesive tape, easily available. After some tests I attached it to the external side. The light bounces through the translucent plastic to the aluminum foil, and no light is lost. The reflected light is diffuse enough, instead of the harsh reflection you would get with the aluminum tape inside. If you don't like the metallic shine outside, you could use perfectly white tape, but then you probably have to cover it again with black tape to make it light-tight. To attach the diffuser to the flash, the design is also more convenient. As the material is rigid, you don't need the two flaps to go all the way below the flash head. You just have to cover the top and the sides. On both sides, you cut a slit to insert the Velcro tape, with the soft part outside and exposed above the flash head. The slits are easy to make: punch two holes at the ends of the desired slit, and then cut to shape with nails scissors or similar thin scissors. The tape has to wrap tight over the small area exposed at the end of the flaps.

Yeayyyyyyyy 🎉 Finally found someone who knows how to do this right. THANK YOU!!!!!!

Hi… I’m the creator of that diffuser.. My channel is under my dog’s name. Thanks for linking to my web site where I also have about 100 tutorials on lighting and photography techniques. As mentioned on my web site the direction of the light is actually more important than the diffusion, something I learned as an apprentice and assistant to Monte Zucker back in the 1970s. At the time he was one of the most successful wedding photographers and teachers who at the time used natural window light for formal portraits and introduced the technique of using dual flash for shooting reception photos back in the 1960s using the first Graflex portable flashes with a simple photocell trigger on the slave. With a dual flash configuration you want to use the flash on the camera as the shadow fill, raising it up on a bracket so the flash head or center of diffuser is 12-18” above the lens so the unfilled dark and distracting nose and chin shadows that fall straight down out of sight and the light creates a symmetrical looking “butterfly” pattern on the face when used by itself. We used a second identical power flash on a rolling stand which was actually a medical IV stand. Positioning the light so it is 45° to the side of the nose of the subject and about 45° higher than the eye line will make it cast the nose shadow down over half the nose which creates a very flattering 3D rendering of a face or any object on the 2D reproduction. When using identical manual flash we would set the off camera flash ‘1 stop’ closer to the subject based on the camera subject distance, a very clever technique Monte created using f-stop numbers for the distances: 16/11, 11/8, 8/5.6 closing down the aperture one stop with each decreasing distance. One of the reasons I created my web site back in 2004 was to explain how to use the then new Canon E-TTL system with Master / Slave dual flash. I created the diffuser a bit earlier than that when still using my Vivitar flashes. They can be made out of anything reflective. In a pinch I’ve created them out of several sheets of bond paper stapled together for rigidity and attached with a rubber band. On my web site at the link in your description you can find a comparison of portraits taken with dual flash and the diffusers vs my studio lights. If you use dual flash as I suggest with the fill for shadows centered and raised any very dark unfilled shadows are eliminated. The lighter the shadows the “softer” the light looks. That’s why if only using a single flash you want to raise the flash on a bracket to hide any unfilled shadows or use the spill out of the diffuser off of the ceiling and walls indoor to create non-directional fill. The larger source the diffuser creates produces larger, more eye pleasing catchlights in the eyes and softer looking specular highlights on skin.

First, great video!!! I have made numerous diffusers and I have one suggestion. Make this really simple, purchase a sun screen for your car windshield that is white on one side and silver on the other. Use these templates with that as the material. No need for anything else but the Velcro. You will not need to make numerous copies and glue them . Just use the windshield sunscreen and add the Velcro. You may want to add extra Velcro so that you can use both sides (make it reversible silver and white). That's it - with this material you can roll it up in a ball, let it flatten out and if will be the shape you want once again. Killer great diffuser. Since i had that material it took less than 10 minutes make.

I made a few of these years ago and also used the same website you did. I used thicker foam for one side so I didn't need to use the plastic grid. This allowed me to stick the two pieces of foam together before cutting. That way I didn't have to fight aligning two pieces of foam together and had perfect edges.

This diffuser works great. I ended up using Velcro squares from Hobby Lobby to adhere everything. They seem to be sticking well and I have a whole pack of spares if they come off.

Thanks for the video, it was really helpful. I made the smaller version last week and have been using it on a Sony A7R3, 90mm Macro and HVL-F43 flash. Really impressed with the amount of light you can diffuse and the creative angles it gives you. For the money, I'd certainly suggest having a go at making one. Something to do on a rainy day 🙂

I guess this is one of the best DIY flash diffuser for macro photography .... loved it and the way you demonstrated. Thanks for the ready to use template .!!!

I like this design, really portable, good looking, and easy to DIY, thanks dude.

Thank you - love this template! I had a piece if 1/4 inch thick craft foam and it worked perfectly on its own - no need to laminate with plastic grid or second piece of foam.

Thanks a lot for your kind thought to share this publicly! :)

Nice ! And thanks for the templates. It's a long time I'm searching a good macro diffusor on commercial sites... some are extremely complicated, quite big and expensive . And I'm convinced that yours is better. Unfortunately... we are in fall, and insects begin to be rare... anyway less interesting than in spring. That lets me somme time ! Have a nice day !

Great video , I've made one of these , not that yours is expensive to make but I made one for zilch , i made it out of a Cornflake box .

Wooow!! This is the best DIY diffuser I've seen..thank you for sharing..🥂

Very well produced video. Thank you. I will give this a try. Subscribed

Thank you so much!! GOD Bless! This is very helpful!💛

@Makify1 Just a little tip. Change the inner colour to white also. It saves toner.

Thanks for the careful documentation of this project! Makes it easy to adapt to one's own needs :-)

Great tutorial, you just saved me a lot of bucks.Thank you very much!

Muy bueno, gracias por las ideas. Voy a probar una versión para mi flash.

Excellent. Thank you.

I was about to order a diffuser internationally, since I couldn't find it here in Brazil...But that was genious! I will do it for sure! Thanks a lot! Only the plastic canvas is harder to find. I might use some another kind of plastic layer there

great idea, have an issue with the larger template, when trying to print it offers 2 pages but each page is page 1 and 2 over laid with details obscured, a little craft work and can still be done but just to let you know its bugged somehow. Updated... the build was easy enough and works really well. Thanks for sharing 🤘🏼

Just wondered why you don't have a diffused cover over the open side of the diffuser? Would this not make the light even softer for macro turning it into a small softbox.? Just curious. You also mentioned that it was tricky to line up the two sticky sides of the foam to the template shape. I was also wondering why not just use oversized pieces of foam and mesh to make a square shape, then place the template over the top of that and cut the diffuser out from the square of material. You will be wasting the same amount of material and would be guaranteed a better finished and straighter edge.

I love these type of diffusers when I have no option but to have the flash on the camera. The only thing I do differently is angle everything slightly off to one side, which I find is more pleasing than having the light straight above the camera, be it for macro or portraiture.

Question about the black backing sheet - would a silver backing sheet reflect rather than absorb light so you get more out of your speedlight? Great video BTW

Cool idea, thanks for sharing!

Niceness. This was brilliant. I typically affix my bounce modifiers to the narrow end of the flash when I'm using on camera flash, though. That way when I tilt my camera to Portrait Orientation (vertically) the flash and modifier stay above the lens and don't end up extremely low and to one side. With off camera flash, affixing it to the broad end of the flash like most people teach is fine. Great DIY vid. Enjoyed it :)

This is Amazing! Thanks for sharing your ideas with us 😀

Genius!! Thank You

Thanks for sharing! Best part at 8:35.😄

Good job bro! 👍🏻👍🏻👍🏻👍🏻

Good little project. To stop the staples scratching the flash, why not stick the black foam to the plastic canvas and then staple the velcro on. Now stick the white foam on. The staples will be completely covered without extra strips.

Nice DYI!!!

Nice tutorial and design..... thanks for sharing

Great video! I want to try to make the larger diffuser, but when I tried to download the template I got an "ERR_SSL_VERSION" error. Can you just tell be the overall length and width (at the widest part)? I think I can copy your excellent work with that starting point.

Awesome! Thanks for sharing

brilliant - thanks so much

I can't download the template. Computer says the site is not secure. Can you provide a different link for download of the smaller size?

Love this design! However, I get a "Secure Connection Failed" error with Firefox and Edge when I try to download plans.

Thank you so much !!😊

Template-Links dead?

Hi there this is fantastic. I have an Olympus em1 m1 mark2 and need to buy the smaller flash like you have here. I don’t have much money and wondered which one you are using or if you have any cheaper recommendations. Then I make this diffuser for it. Thankyou 😊

Hi, first of all thank you for sharing this video. This saves me a lot of money and making it myself is always more fun. I only have one question, what is the thickness of the craft foam? Thanks and I hope I get an answer from you.

super ! merci beaucoup !

Gracias, ya hice el mio😊

thank you so much

Woowwww !! Thank you so much !!

great idea thank you.

Nice video thanks. For some reason I am not able to download the template to print . Is there any other format available?

Very nice. Thank you Sir!⭐⭐⭐⭐⭐

The links for the templates are not working (ERR_SSL_VERSION_OR_CIPHER_MISMATCH). Can someone upload the templates who downloaded them when the links worked? Thanks.

Thanks for fixing the download link.

Very nice. Thank you Sir. ⭐⭐⭐⭐⭐

Thank you for this video! I want to make my own diffuser based on your template and I do have the Godox TT350O flash as well. Do both sizes fit on that flash or only the small one?

Hi great video, here I cant find the plastic cavas, I will try with a plastic from a magnetic resonance. thank you

You deserve an Oscar. Thanks

Hi, I'm unable to open the links of the templates for the diffusers. Idk if you could update the links so that it is possible to download them . Please and thank you 🙌🏻

Thanks !

can't get your template links to work. The super nova link is OK

Super !

The diffuser should be as close as possible to the subject. It will become or near to a spotlight source if too far like your one. And the flash is the father, the better in order to soften the light.

no links?

Hi, the link for the download is broke. Can you check pls. I can't wait to try build this. Great video ty.

I was going to get the patern but the link doest work ty.

dimension may please be provided. I appreciate as you have completely explained thoroughly in very easy way one could understand very easily now I can make if do a favour if dimensions be shown Khalid mohiuddin Lahore Pakistan

Thanks for that and providing templates... However, it's a big reflector not really a diffuser...

Las grampas de la parte blanca van a rayar el flash, por lo demas me parece una gran idea

If you REVERSE the anvil on the stapler, you'll flatly PIN the staples to the foam - not bumps.

Hello, excuse my poor english, why do you use platic canevas inside ? What is the interest ? Thanks

Fotos de ejemplo, con y sin el difusor

Lien not found

I think I learned more from the bloopers.

Deine Webseite funktioniert leider nicht :(

OK for horizontals but some people take verticals and this design is not as pleasing from the side.

Only downside: Portraits in Portrait-orientation

The only problem is your diffusers do not illuminate the underside of your subjects.

Its a reflector not a diffuser