In this video I show how I adjust the sawblade parallel to the miter grooves in the table of the Makita 2704 table saw. Presented in a monotonous and un-exiting voice!
Пікірлер: 23
@matttijah Жыл бұрын
thank you very much! make more such a videos, you make peoples life easier a lot!
@LipSonic3 жыл бұрын
Excellent! I bought a used 2704 and this is really helpful!
@maf20183 жыл бұрын
thanks! I have a 2704, now I know how to adjust it!
@omaromar-lg3yu3 жыл бұрын
Great job thanks I found it very helpful
@peterroxo94883 жыл бұрын
I have been trying to figure out how to do exactly what you did. You have made my life a bit easier. Thank you very much.
@atikam29563 жыл бұрын
Thanks Peter! The whole reason I made this video was because I could’nt find it myself.
@Repiolariel3 жыл бұрын
Just what I needed. Thanks a lot!
@atikam29563 жыл бұрын
No problem Ar Iel. Anything else you want to know about the 2704?
@Repiolariel3 жыл бұрын
@@atikam2956 any modification or upgrade could be interesting. Thanks!
@morganphalen Жыл бұрын
Thanks for vid! Have you had any luck with the fence being straight after you pull out the side table for wider wood?
@SillyMonkeys Жыл бұрын
thank you, just bought a used one of these, going to put a new blade on it, its pretty straight forward?
@xionxion53933 жыл бұрын
Hi. soo good ... I´m thinking to buy this Makita 2704 or go to next level of table saw, but I ´m not sure. So could you help me please? And also, I would like to ask you if this task ("adjusting the blade") is every time when you need to cut? thank you...
@morgsjnr2 жыл бұрын
Thank you for the video. I have recently brought this table saw. Does your right extension table sit lower than the main table? Many thanks.
@atikam29562 жыл бұрын
Hello Neil! Thanks for watching the video. Sorry for the late reply. I just checked, and yes, it’s about 1 mm lower (1/32"-ish)
@grympinski3 жыл бұрын
Hi. Do you think this table saw is capable of rip cutting oak logs 9 cm thick?
@atikam29563 жыл бұрын
Hello! Yes, with the right blade (rip blade) it will be able to rip 90 mm oak logs. The cut capacity of the 2704 is 91 mm in height. Just take it easy and dont go to fast.
@Sly_Wolf_12 жыл бұрын
Nicely done, but how ridiculous of makita to design it in such a way that you have to turn it over to calibrate it.
@brucegray9155 Жыл бұрын
Is it the same process for the Makita MLaT100?
@brucegray9155 Жыл бұрын
Sorry, MLT100
@Geowebbie Жыл бұрын
Same question? Them 2 hex nuts are there but I loosened them and the carriage doesn’t budge 🤔
@starychomik6470 Жыл бұрын
Hi, I've just watched your video and think you overworked the whole process. First of all - you really don't need to tip your saw over and dissassemble it. Those two screws are also accesible through a tiny slot (10x100 mm) right under the table and above the bevel angle wheel. They are hex headed so you need a 10mm wrench to turn them. It's a bit pain in tne ..., but still more convenient than tossing a saw around the shop. And second - use a dial indicator instead of a ruler, it would allow you to make more precise adjustment. Looking at the indicator's readout move the carriage with a flathead screwdriver until both readouts are the same, then tighten the screws. 5 min job.