I go through all the features and a personal review of the 18V battery powered Makita XNB02,16 gauge finish nailer after one year of regular use. This video is not sponsored by anyone.
Пікірлер: 25
@jbgaming24052 жыл бұрын
Do you have to pull the magazine spring up to load nails in or can you put nails in and then pull it over the nails?
@MechanicalMike2 жыл бұрын
yes, has to be pulled all the way back to load
@BAYERNEMPIRE Жыл бұрын
How do you shoot the nails into tight corners? I think the safety plunger gets into the way. Maybe it’s just me?
@MechanicalMike Жыл бұрын
Haven't had a problem with it so far
@josephKEOarthur Жыл бұрын
Do you have to lubricant the nail release area? Shooting slot…
@MechanicalMike Жыл бұрын
I have had to a few times. It starts to jamb if it gets too dry
@nomsolo99352 жыл бұрын
What size Makpac box do you recommend for storage?
@MechanicalMike2 жыл бұрын
Not sure about that one. You'd have to check specs of the nailer online
@4i042 жыл бұрын
Un my opinion macpac 2 will be fine, I don't have that nailer but I have a macpac2.
@curtiswall5972 Жыл бұрын
My XNB02 after a years use. We use it for follow up / punch listi g projects (once a week on average) only nails every 4rth shot...any comments?
@MechanicalMike Жыл бұрын
Sometimes the slider on the magazine that pushes the nails gets caught up if there's debris in there. It can keep it from putting tension on the nails. Try cleaning it out and spraying in some graphite dry lubricant or dripping a little bit of tool oil on it and see if it resolves the issue. Mone also has a harder time pushing nails all the way in if the amp hours on the battery are too low. Lastly, making sure you have 16guage nails in there, not 18 Guage.
@leegarnier9396 Жыл бұрын
I have the DBN600, which is the partnumber used outside the US I believe. What I found is that shooting overhead caused more empty shots. I also found the rubber tip in the box and put it back on. That seemed to result in in fewer misfires. I'm not sure how these influence the mechanics. I suspect that the weight of the machine influences the way I press the tip and may cause slight alignment issues. But this may all be bull. I'll have to try Mike's suggestions.
@josephKEOarthur Жыл бұрын
How do you store it.. on the side or in a box 📦 fitting?
@MechanicalMike Жыл бұрын
I just hang it up in my job trailer from the belt hook that comes with it
@CP-ok1gv2 жыл бұрын
Is this good for trim and prehung doors or patio sliding doors
@MechanicalMike2 жыл бұрын
It's great for interior trim work, yes. I wouldn't recommend it for exterior trim as it could peel of with weather due to thin nails that aren't treated for rust.
@josephKEOarthur Жыл бұрын
@@MechanicalMike good point about the rust.
@simonrizk44512 жыл бұрын
thank you
@kishdogg15942 жыл бұрын
Do they make a Framing Nail Gun 18v
@MechanicalMike2 жыл бұрын
They have yet to release a cordless framing nailer. I am patiently waiting. I imagine it would be a dual battery 36V or the new 40V. Dewalt and Milwaukee are way ahead of Makita in that realm.
@kishdogg15942 жыл бұрын
What's the Biggest Size Nail for Makita? Does anyone know?
@MechanicalMike2 жыл бұрын
@@kishdogg1594 they make a pneumatic framing nailer, but this is currently the largest battery operated nailer that they have. I imagine that will change pretty soon