I love the dynamic guide hole that makes sure your putting the component in the exact correct spot!
@nadabrainiac5 жыл бұрын
It only repeats the position you told it to go to. So you might put it in the right spot every time or the wrong spot every time. And it does nothing to control the orientation of the part. Extremely limited value and applications, considering the high cost.
@elliotth303 жыл бұрын
With that intro - I thought I was about to start playing Ratchet and Clank on ps2
@ahav3847 жыл бұрын
great job!!
@Deathbyfartz3 жыл бұрын
man this is the coolest toy i seen in a long time :O
@MP-ui5qy2 жыл бұрын
Muito interessante. Nunca tinha visto placas construídas feita a mão.
@WETDOGBR6 ай бұрын
Sabes oq e' aqueles pontos vermelhos entre a pasta de solda?
@nubi93157 жыл бұрын
Did you notice 3:35 wrong direction of IC mounting, it catched my eye.. 100% secure, yes)
@EdwinvandenOetelaar7 жыл бұрын
good catch, you were paying attention. (like someone placing smd should have been doing) ;-)
@fseeletronicos6 жыл бұрын
I did noticed the same. This machine needs to improve and solve this problem.
@Dr.Stein996 жыл бұрын
Or - not make a 100% claim gaurantee that no error will happen in the first 5 seconds of video.
Erich Stein the video did not make any claims that no errors would happen. It stated 100% SECURE PLACEMENT. Nothing more.
@aismtspareparts30735 жыл бұрын
Great operation!
@phatman8083 жыл бұрын
When you wanna build boards like grandpa used to but everything is smt
@feintha3 жыл бұрын
My fear of SMT components increases.
@dineshrewari92164 жыл бұрын
NICELY DEMONSTRATED
@orsolyakomari85787 жыл бұрын
Ilyen az,amikor az ember egyesül az általa megalkotott technológiával.Nagyon szeretnék egyszer ilyen géppel dolgozni...A jól kiválasztott zene a szükséges plussz!Proto termékekhez is egyedi kis darabszámmal gyártott PCB-hez is kiváló.
@kenwood_94743 жыл бұрын
Yes human.. Do my bidding! Assemble my brethren!
@JoJayO4 жыл бұрын
wow sir ur intro impressed me :D
@user-vr9lg2ox3y6 жыл бұрын
очень хорошая машина для создания прототипов или мелких партий готовых устройств
@peoplethesedaysberetarded7 жыл бұрын
Content starts at 0:23.
@aamr98114 жыл бұрын
😂😂
@lapnguyenxuan86326 жыл бұрын
Thank you!
@mounirabdallah60186 жыл бұрын
Thankyou excelent video
@victabeer39603 жыл бұрын
Very cool , I thought I was useless when components stuck to to the tip of my soldering iron .
@bestbuildpc3 жыл бұрын
Amazing. So beautiful!
@EduardoSilva-mq5mq4 жыл бұрын
Bem legal ver essa montagem de componente smd
@RaoulLeDegueu2 ай бұрын
c'est génial 👍
@ECrackers6 жыл бұрын
Awesome!
@__-pg3so3 жыл бұрын
To integrate a general purpose common component placement arm set will be a good investment.
@agstechnicalsupport3 жыл бұрын
Today SMT is is the technology in electronics and if quantities are not very high, this semi-automatic system is promising !
@visicios6 жыл бұрын
Excelent!!!
@RakeshSingh-tz7mh6 жыл бұрын
Nice
@imho22783 жыл бұрын
Beautiful
@andreamodiano4 жыл бұрын
Excellent.
@MarcosSilvaObel5 жыл бұрын
Nice man
@igorovcharov74243 жыл бұрын
Для предсерийной партии вполне хороший инструмент. Правда стоить будет как деталь от самолета. :-))
@zgk_tech81304 жыл бұрын
Amazing please must see this will help you and me both... @ Thanks...
@rupeshvadoliya626 жыл бұрын
Good job
@jahirosolar68403 жыл бұрын
Excellent video @Paul Cooper, do you construct manipulators too?
@user-zr9xr5is3d4 жыл бұрын
Fantastic
@issemxfi Жыл бұрын
great solution for rework and prototype of high value products in high power electronics or medical or military or aerospace sectors.
@spongedebfatpants1308 Жыл бұрын
Wow that probably takes forever.
@mshakil86 жыл бұрын
very nice
@user-eh3bm3ip7e5 жыл бұрын
Главное не чихнуть.
@jonyzhu65314 жыл бұрын
nice!
@Alex-fh2th5 жыл бұрын
Нормальный полуавтомат... вот бы раза в 3 подешевле и можно использовать на небольших производствах.
@stanza27625 жыл бұрын
почему его все называют полуавтомат если все вручную ?
@Alex-fh2th5 жыл бұрын
Потому и полуавтомат , а не автомат что без человека не работает...))
@user-jj9xh9ec1j5 жыл бұрын
WAW OK GOOD YES THANKE YOU THANKS
@kwsa46576 жыл бұрын
nice
@pavanbobade11147 жыл бұрын
grate
@gkviluminacion64015 жыл бұрын
maravilla
@hellopandit95 жыл бұрын
wow nice
@a6dulsalam5115 жыл бұрын
woooow 😮😮😮😮😮
@Rowow7 жыл бұрын
Why though? What advantages does this have over a automated one?
@BMSworldNZ7 жыл бұрын
I'd imagine that this product level would suit those smaller businesses who cannot afford to outlay more than $150,000 on an automated pick and place machine - especially considering that that small business might already have the skilled staff on site, which makes the case for a serious investment in an automated pick and place machine even less tangible.
@Rowow7 жыл бұрын
$150,000? Serious? You can get them for under 10 thousand or build one for a fraction of the cost.
@BMSworldNZ7 жыл бұрын
Well admittedly, $150,000 was an assumed figure - and it's also very difficult to find pricing for an Industrial PnP machine. All the websites want you to sign up to get prices :E
@joeambly68076 жыл бұрын
A "real" business isnt going to DIY a pick and place machine or buy a 20 year old used one. Plus the setup times on many large machines outweighs any time advantage. Hence the niche for this machine.
@Arterexius6 жыл бұрын
Joe Ambly >> Define "real business". Neither SpaceX or Tesla started out buying high end equipment right off the bat. I wouldn't consider either of them not being real businesses
@randrianjafiniarivoandriso66875 жыл бұрын
I like this machine
@blindscience19193 жыл бұрын
I would have loved to hear what you had to say. Since I can't see well enough to read it.
@ecofuelbox7 жыл бұрын
Fantastic tool ! What is the mark and viscosity of solder paste that you are using ?
@Vik_ru7 жыл бұрын
Any can be used..
@Bianchi773 жыл бұрын
Nice video, thanks :), where did you get it from ?
@user-kc6lo6mb7h3 жыл бұрын
Great, and we have SMT whole line equipments, are you interented in it?
@civick2052287livecom4 жыл бұрын
I want one!
@bachumiyamalik74907 жыл бұрын
goods
@rjordans4 жыл бұрын
So, do they also have a version for us are left-handed?
@IvanFedulov3 жыл бұрын
Im also left-handed, but its actually pretty convenient to operate with right hand
@okan18082 жыл бұрын
@@IvanFedulov Do you have one? If yes what are the top 3 disadvantages you would count? Many thanks in advance
@MrAndri26 Жыл бұрын
Hi, for component in the carousel, how do you ensure the pick-and-place probe placed exactly in the middle of the component? it seems the guided hole did not take into account the offset of the position of the component when you pick it.
@kinderwood Жыл бұрын
I was curious about that also. Looking at the placement of the two ICs at 3:21 to 3:32 it looks like the guide pin gets you to the nominal part location but gives you some wiggle room to manually align while placing.
@user-si4tq2eb5p2 жыл бұрын
Это лучшая система ручного монтажа.
@Cr33p227 жыл бұрын
why would you ever want this. Save up a bit more money to buy an automated one
@HDFoxra7 жыл бұрын
idk why anyone would wanna buy it either. Considering realistically..... this machine would have to cost WAY more than a normal PnP machine... considering the extra shit you'd have to build in to allow human control..
@goodwill76436 жыл бұрын
I think next release will have extra option, which will allow you manual, semiautomatic and automatic options.
@darthnegativehunter86596 жыл бұрын
the reason could be the freedom from configuring the machine for a quick prototype, but if the automatic one has a manual option, then... it's pointless
@dovycat63746 жыл бұрын
lol
@djolencebicko95315 жыл бұрын
Because when your P&P examle place qfn qfp or bga wrong (with offset by x y or teta) u can remove component with this manual p&p without destroying solder and than manualy replace or place by P&P..
@w888w4 жыл бұрын
I like this
@emirkayrak3 жыл бұрын
It's like an engineers wet dream
@maxdyupin27356 жыл бұрын
за 15к евро я и руками пособираю без проблем.
@aleksandrgalkin76695 жыл бұрын
NeoDen4 полностью автомат, за 10к$ взяли, а тут каждый компонент вручную выставляешь....
@stanza27625 жыл бұрын
Ну а если одна плата нужна только ? как на автомате ?
@maxdyupin27355 жыл бұрын
прототипы и собираю, ставим шарики 0,35 и все, вплоть до 0201, и правлю после вот таких машинок
@9163634 жыл бұрын
По видео видно как некоторые компоненты криво встали. не вижу сложности сделать полностью автомат, который даже при штучном производстве сделает все точно. Какая разница, если здесь позиционирование все равно идет на автомате. Подобные машинки не сложнее лазерного гровера на ардуино. Ну, или немного сложнее. Вся проблема в грамотном ПО, но и эта технология уже далеко шагнула вперед.
@invisiblealex0074 жыл бұрын
я вообще подумал что первую палату ты руками записываешь движения и перемещения, а дальше робот копирует эту последовательность. Так делают все автоматы и сварочкики))
@AB-zh6lp5 жыл бұрын
I think, this one is also not cheap. Finaly a automated one is much more efficient. Before i use this i can also use just by hand.
@sasa765645 жыл бұрын
Bello
@safataqwa75146 жыл бұрын
Hi respected sir video is very intresting thsnks a lot. Seeing this i m very happy
@vinodpawar61753 жыл бұрын
Super
@TrumKS3 жыл бұрын
intro dữ thiệt
@fhellak88476 жыл бұрын
I need a full automated one.
@Smthelping6 жыл бұрын
we have a full automated
@Smthelping6 жыл бұрын
if you need ,Please contact me: ming@smthelp.com
@pushpendras_kitawat35396 жыл бұрын
juki 2080l and fx-2,and samsung neo ,cp45
@aismtspareparts30735 жыл бұрын
How’s the accuracy
@__HJK__3 жыл бұрын
Если система видит на какой угол нужно повернуть деталь и указывает местоположение, то я не понимаю почему ее не оснастили дополнительными четырьмя двигателями, а на человеке оставили только инспекцию If the system sees to what angle the part needs to be turned and indicates the location, then I do not understand why it was not equipped with additional four motors (moving + rotation), and only an inspection was left on the person
@gxggao30393 жыл бұрын
牛逼😂
@abbasi57573 жыл бұрын
کاش میشد تو ایران هم به این وسایل دسترسی داشت
@NguyenTam-zl2tk3 жыл бұрын
Intro video verywell. Where is link? Help me please!
@KeesHessels6 жыл бұрын
ssoo, what do i exactly gain by using this (not so very cheap) machine ?
@julianreverse3 жыл бұрын
Speed and accuracy.
@williamhuang53292 жыл бұрын
Hanzhen harmonic drive gear , over 30 years experience , strain wave reducer, robot joint ,
@CoquiAudio5 жыл бұрын
you know that tweezers and a big table cost less than that right?
@UrBaNMCPaladinZ4 жыл бұрын
you know a donkey costs less than a helicopter right?
@alexanderfederowicz4 жыл бұрын
At 3:37, it looks like component, "RIVX 55M" has the lower left first two pins soldered together as an accidental short ???? Hope I'm wrong... Honestly I would o with rectangular solder needle dispensers, as they might avoid such tragedies...
@Graham_Wideman Жыл бұрын
If the board is still being placed, then the solder paste has not yet been melted. When it is, the surface tension will easily pull the solder onto the pad. This is pretty standard in SMD soldering, and is part of the reason for the solder mask layer.
@hayel20157 жыл бұрын
😀😀😀
@denrudenko77245 жыл бұрын
and what music track is playing?
@imho22783 жыл бұрын
Kf016901 universal mind...in credits
@ilhancoskun76324 жыл бұрын
hello where can i buy this product ?
@tuantrinh10625 жыл бұрын
amz
@JohnyDays692 жыл бұрын
Just the flipping mechanism killed me from working in an aerospace company... no time for such waste of time... XD
@MirandaEartherCaller4 жыл бұрын
by the time you set that up you could build one by hand easy, if your gonna do volume just get the pnp, does't need to be a fancy one either, get a used one with a few perks and warranties. You could modify that setup and make is faster by using a microscope and a mouse controlling the placement wand instead of this non-sense.
@iceofautumn8906 жыл бұрын
Not to be confused with Full Semi Auto.
@Anonymous-je7qc3 жыл бұрын
Why would you want semi-automatic when you can have full auto for less than $2k (at least, those that sort of work)?
@Graham_Wideman Жыл бұрын
Because this takes a whole lot less setup, allows you to populate the board progressively in any order for troubleshooting purposes, substitute components on the fly, repair a board from which you have removed components, and so on. It's not intended for significant production runs.
@volidol3 жыл бұрын
Все это круто, пока тебе не надо собрать 10 плат номенклатурой в 120 компонентов.
@1337PANDA6 жыл бұрын
Placing of components , that's so frustrating
@anggaradwi7020 Жыл бұрын
I think this isnt meant for mass production,this is for making some prototype sample pcb
@casualuploadsh_gandham66233 жыл бұрын
Sir Any place to work there. I like to learn and do works on PCB.
@marceloguzman45576 жыл бұрын
I liked the tutorial I am smt operator here in Tijuana Mexico can upload videos of commands for universal machine automatic insertion in Spanish. I am interested in greetings from Mexico.
@nickfirst72494 жыл бұрын
Greetings from Kiev!
@ubuntupokemoninc6 жыл бұрын
I bought an old quad for a couple grand, probably cheaper, ants its automatic
@jeetusolanki74 жыл бұрын
How to solder them then palaced
@OfficialyMax3 жыл бұрын
idk why but I want one
@BharatKumarBellamkonda4 жыл бұрын
Flipping station
@alking70077 жыл бұрын
how much?
@editorialtakk6 жыл бұрын
Ramy a its not in your budget keep it up
@shamsheertnrp48806 жыл бұрын
Ramy a f
@kuldeepbhullar59865 жыл бұрын
Good work
@abeditani82934 жыл бұрын
How much it costs approximately ? And where I can order it online
@ProtonOne113 жыл бұрын
you can get a quote at the fritsch website, but make sure you're sitting down before you open theyr email... it's probably around 15k€, soo, better go buy a simple but fully automated SMT placer for 5k€ in asia, do it completely by hand, or actually buy something else that is a bit more reasonably priced...
@kieron8505 Жыл бұрын
3:38 IC is wrong orientation.. Potential flaw?
@happyanimation84783 жыл бұрын
It's price and availability
@beutyfullmoments34254 жыл бұрын
Wat is the price sir plz tell me i want 2 buy this 1