fwestenberg thank you very much for creating the integration and you Mark, for the very helpful video with which I was able to integrate the cam very easily!
@RichSimpson3 жыл бұрын
I tried the integration again after watching the video. Seems good. If you want the sub stream rather than main, you can set that in the configure section within the integration. I had to leave a " / " in the thumbnail section to let it save the config (blank as default isn't accepted). Now I can have 8 cams on the screen and they load quickly. I am not sure if you can add the same cams for their HD main stream, I guess so and so I could have 16 cams (but only really 8) added so I have the sub and main together. Will have a play around and see. Then have the live stream of the picture glance = sub, press it to go to main stream... just thinking as I type! The motion sensors seem a bit flakey, sometimes always on, other times always off.
@RichSimpson3 жыл бұрын
You cannot add the same camera twice, so other option is to setup the cam in config/yaml as a generic camera using the right url. then use that as the high quality stream.
@JUNK4UCREW3 жыл бұрын
Hey Mark, I havent watched the video yet as catching up with al your older stuff but a lot of people including myself are using "Blueiris" as their CCTV. Not sure if you have used this but it would be great to see this intergreated with HA.
@MarkWattTech3 жыл бұрын
Hey Craig. I do plan on playing around with and covering Blue Iris :)
@blamp56663 жыл бұрын
Mark thank you, thank you for all your videos. I have finally made it around to my REO link cameras (RLC-529). I have the integration all set up in my home assistant, however, it is not finding my camera when I put in the IP Address, username, and password. I receive an error message "Failed to connect with the camera". The camera is on the network and running perfectly in the reolink app......any ideas??? Thank you in advance!
@ZacHarvey3 жыл бұрын
I get the same. Did you figure it out?
@lucb22336 ай бұрын
Thanks for the video. But what about ptz button. I have a trouble with that , sorry for my English ;-) but when I use move right entity the camera goes to the far right or left and so on...
@christofpalmers9953 Жыл бұрын
Hello Mark, Very interesting video, but already 1 year old, and the new Reolink HA integration being improved a lot, I was wondering if you still need the HACS integration, I guess not ? And if the Reolink E1 Zoom support person detection instead of only motion detection ? Thank you in advance !
@MarkWattTech Жыл бұрын
Hey Christof. I would go straight for the new integration that is available without HACS. It’s been getting great support the last few releases and is very reliable :) The E1 Zoom does support person detection but in my experience it isn’t super quick to respond.
@jamegrabham99923 жыл бұрын
Hi Mark...Great video...thank you...Most of my cameras are Reolink, and I used the same integration (from Hacs) that you show...I have noticed that the HACS is continually updating every several weeks... could you maybe go thru some automation with motion, etc...???and is there somewhere that can trigger "record" (to a NAS) when motion detected??? I am also working on having the cameras go "idle" when we are home, but go to "ready" (with notifications) when we leave the house with the presence detection...this is still a work in process...:( Any help sure would be appreciated...thanks again.
@MarkWattTech3 жыл бұрын
Hey Jame. Yeah more recently it has gotten a few updates (Which is good :D). I do plan on covering automations with motion, PTZ and recording stuff, and also a privacy mode. I don't have an ETA when this will be. But it's storyboarded and just needs to be recorded. Keep your eyes peeled :) Check out my Facebook group as I will be holding a poll there on some of the videos I have planned for people to vote on.
@jamegrabham99923 жыл бұрын
@@MarkWattTech Will do...please keep up the good work...:)
@lpkitson2 жыл бұрын
Hi, great and informative video. Just wondering if y want to add more than 1 reolink camera, how is that done? I have added 1 camera ok but when I click on the integration I cants get to the card that allows you to input the lP and login details of the 2nd camera. Thanks in advance
@MarkWattTech2 жыл бұрын
Choose the add integration button again, select Reolink and it will prompt you for the second cameras details :)
@MatterSec3 жыл бұрын
I've added the custom addon into HACS and rebooted. But no luck on it showing up under main integrations :( any ideas? cheers
@MarkWattTech3 жыл бұрын
Try clear your browser cache and it should appear :)
@StringerBell3 жыл бұрын
Hey there, can you "arm" the camera when you leave home, so it can notify you if something happens? Also does the 10 seconds delay apply to that case or only when viewing the stream?
@MarkWattTech3 жыл бұрын
Heya :) With the Reolink integration there's no "Arm Mode". But what you can do instead is toggle on and off the various features that an arm mode would actually do (e.g. turn on recording, motion sensor etc.). The delay is just for the stream. Everything else is pretty instantaneous.
@StringerBell3 жыл бұрын
@@MarkWattTech Thank you, Mark! Is there possibility to trigger automation based on SOUND detection from the camera?
@mathieugoy22363 жыл бұрын
Hi, thanks for the video. I have the E1 Zoom as well and made the same integration. Do you know if there is any way to get the PTZ control in HA?
@MarkWattTech3 жыл бұрын
Hey Mathieu. You can use the PTZ functions yes. Check out the reolink_dev.ptz_control service. Cheers
@mathieugoy22363 жыл бұрын
@@MarkWattTech Brilliant, I'll have a look on it. Keep on with the good work
@MarkWattTech3 жыл бұрын
@@mathieugoy2236 you will need to use the reolink desktop app to set positions. You can then say turn to position 1 etc and the camera will move to that predefined spot. Works really well. If not you will have to say left etc and then stop. Or it will just keep moving in that direction.
@drreality13 жыл бұрын
Thanks Mark I find that after a day or more, the live view get delayed by hours , meaning it starts viewing broadcast hours old, have you had such a problem ?
@MarkWattTech3 жыл бұрын
I haven’t had this issue no. Are you using the “preload” feature in HA? I found this has happened on other cameras when I have used that feature. If you go into the Reolink camera and use the reload option do the cameras re sync? Check your logs to see if there is anything causing such a big delay on your streams. Cheers
@drreality13 жыл бұрын
@@MarkWattTech thank you so much, it’s probably the preload then
@StringerBell3 жыл бұрын
Hey can you trigger automation based on sound detection from Reolink?
@MarkWattTech3 жыл бұрын
I don't think you can.
@ortigonover3 жыл бұрын
Hola Mark! AFAIK you can add any onvif camera to HA just adding the RTSP address into de configuration.yaml and this works great to take snapshots and get some notifications. Till now I trigger the automation with a PIR sensor. What you show here for the Reolinks it's somehow exportable to any other onvif camera? ( I mean to use them as well as motion sensor) Thanks in advance! Cheers!!
@MarkWattTech3 жыл бұрын
You can add then directly via rtsp yes. But you cant use the sensors or ptz controls. This integration is specifically for Reolink cameras. Hope that answers your question?
@ortigonover3 жыл бұрын
@@MarkWattTech it does! Tanks!
@MarkWattTech3 жыл бұрын
@@ortigonover the Ptz controls for this camera work well. You can also define set positions and then just call a script etc and have the camera move to that spot.
@ortigonover3 жыл бұрын
@@MarkWattTech +1 for reolink!
@ortigonover3 жыл бұрын
Hi again Mark! Do you plan to show us something more deep with the cameras like AI to identify people ringing the bell with frigate or similar? Would be great!! Thanks a lot !!
@hristohristov52462 жыл бұрын
Hello Mark. I bought an E1 Zoom. Please tell me how to activate motion detection😩. I followed your steps from the video. Everything is exactly as you show it but the sensor does not detect any movement. Do I need to add anything extra to config.yaml?Do I need to make any settings through the web interface or through the Reolink mobile application? The sensor works perfectly on the mobile application but does not work in HA....
@MarkWattTech2 жыл бұрын
You shouldn’t have to and they should just work. Have you tried rebooting HA since adding the reolink integration?
@hristohristov52462 жыл бұрын
@@MarkWattTech I understand. I tried the camera with onvif and motioneye just the sensor does not work. I will just reinstall HA,maybe I messed things up somewhere. I've been learning to work with HA recently.. there is no point in shooting in directions. Thank you for the quick response :))))
@MarkWattTech2 жыл бұрын
@@hristohristov5246 The sensor will only appear and work with the HACS integration. Just make sure you are using the latest version of the integration, HA and Camera firmware.
@EricOnYouTube2 жыл бұрын
Any updates to this?
@jonathanp80123 жыл бұрын
Hey Mark, love the videos. I've run into an issue though. I get all the way to installing the integration but it doesn't seem to pick up my specific camera. It successfully adds the integration but no entities or services, even though it was named the same name as my camera is called within Reolink. Any ideas?
@jonathanp80123 жыл бұрын
Sorry, no device not no service
@MarkWattTech3 жыл бұрын
Hey Jonathan. So when your adding the camera its adding with no entities? Which camera are you using?
@jonathanp80123 жыл бұрын
@@MarkWattTech it's a rlc 420 poe camera. Yes nothing gets added although it says successful
@MarkWattTech3 жыл бұрын
Hi Jonathan. Did you have any luck with this?
@jonathanp80123 жыл бұрын
@@MarkWattTech No, Mark, still having issues. I tried uninstalling everything and doing it again, plus upgrading firmware on the camera and still no luck. The integration adds ok, it just has no devices or entities yet it names itself the same name I have for the one and only camera I have.
@necrobot22622 жыл бұрын
I have a Reolink E1 Zoom and a Google Nest Hub display. I created an automation that shows the camera feed on the display when motion is detected, but the video shows with a delay of 28~30 seconds. I tried with both the ONVIF and the Reolink-Dev integrations, both have the same delay. Such a long delay makes this completely useless. If I use MJPEG, the image shows up in 1 second. But it shows just a single screenshot, it isn't updated. I've been on this for a full week now, tried everything (also ffmpeg and WebRTC), nothing works. Becomming desperate here.... 😢 How can I get a live video feed from the Reolink on the Google Nest Hub display with an acceptable delay (max. 3 or 4 seconds). Even an MJPEG that would update maybe once a second would be OK. I prefer not to go the BlueIris/MotionEye/iSpy/NVR route though. I'd like to do this inside HA natively.
@MarkWattTech2 жыл бұрын
What's your automation doing? Are you casting the camera feed directly?
@necrobot22622 жыл бұрын
@@MarkWattTech I have it working now, after weeks of experimenting. But I was not able to get it working inside Home Assistant alone. Ultimately I had to resort to Agent DVR and get the video feed from there. Now it responds very fast and the delay is only about 1 second. Perfect for what I wanted. But I had to create another Windows VM just for running Agent DVR. Ah well... I'm happy it works now :)
@AlexBoltonKing2 жыл бұрын
Gutted I can't use this with my normal E1 :(
@neil79023 жыл бұрын
No E1 pro. Oh well 😔
@MarkWattTech3 жыл бұрын
I think you can still add the E1 Pro via RTSP. You wont get the motion sensor access etc or PTZ, but at least you will have the feed