Beautiful work custom fitting the j trim! Like the attention to detail!
@MrPostFrame Жыл бұрын
Thank you very much!
@tcardinal954 ай бұрын
Best window install with great installation instructions! Thanks!!
@EasyAim14 ай бұрын
Great job. We used Haslet Frames around all of our windows and doors after installation. The frames butt up against the J-channel flanges and give the building a better look than having that steel flanges from the J-channels sticking out.
@eastmanresearch3143 Жыл бұрын
You are a great teacher -
@chrisellis7847 Жыл бұрын
Love this! Its like watch Kyle @ RR Builders!!! top notch work and great attention to detail!!!
@Overpar73 Жыл бұрын
Nice attention to detail as always guys! Everything is looking fantastic!
@MrPostFrame Жыл бұрын
Thanks!
@marshacowan12527 ай бұрын
That looks great!
@aintright3889 Жыл бұрын
Best Video I've seen for a leak free window install. Bravo:) you wouldn't happen to have any video or tips on installing a turbine/whirley bird vent on a 1:12 pitch roof that has PBU panels? Thank you, your a great Teacher.
@Bwatt50008 ай бұрын
I'm not sure how your "beeper" is designed but we cover ours with tape. Keeps in audible but isn't ridiculous when you're close to it. OSHA approved, of course lol
@RebeccaThompson-v8bАй бұрын
Is it important to always put a line of silicone? Between the j and the window?
@jwalt92 ай бұрын
How do you trim the window if the rib on the siding is right next to the window? Do you have a video for that? Great videos ... thank you!
@bradpassow4 ай бұрын
So, how do you trim it out if you have the misfortune of having the window end on a rib? Unfortunately, there was no way to adjust the layout to prevent it from happening because windows had to be centered over sinks. Thanks for the great videos!
@kylebryan13 ай бұрын
im interested to know the same thing. i have two windows that landed on ribs and of course they are leaking!
@justincunningham54573 ай бұрын
I will run my header channel out to the flat and match the overhang on the the other side. Some window details just have to be slightly different. Just the metal world.
@frankabel5064 Жыл бұрын
Very nice video(s). Do you have a video or link that shows how to intall the windows right on top of wainscoting? Also any videos on how to space out the girts for the wainscoting? Thanks
@Box545x397 ай бұрын
Any chance you could explain how you would remedy a rib landing on the side J-channel? This was a great step by step to follow, thanks.
@linovie4 ай бұрын
3ft coverage c to c of rib, have a rib land dead center of the window and you'll come out in a flat
@justinrrizzo3 ай бұрын
Doing this job soon on my covered deck. My windows are all over the place, so I don't think I'll be able to get a flats on either side of all the windows. There is likely to be a rib somewhere next to a window jamb. How do I work with this?
@AppleKid5 ай бұрын
what kind of windows are those?
@jacobcarlson3904 ай бұрын
When barndo building Is it normal practice to not use sheathing on the roof or walls like typical construction??
@MrPostFrame4 ай бұрын
It’s not required because you get shear strength from the metal. However, we now sheath all our roofs for many reasons. If you don’t want sheathing on the roof, like this client we require drip stop on the bottom of the metal.
@aaronz9770 Жыл бұрын
Question. .. how do you do the rake to valley metal tradition on the porch gable? I am scratching my head as I need to Figure out that transition before Monday
@sensequest Жыл бұрын
nice
@MrPostFrame Жыл бұрын
Thanks
@islandtooldepot47723 ай бұрын
great video!!! question... does the metal panels come with the screw holes pre-drilled? if not, what method do you use to get them straight across all yhe panels? TIA
@MrPostFrame3 ай бұрын
We measure the girt locations and pre-punch multiple panels at a time.
@paulmaxwell88513 ай бұрын
I do some VERY careful measuring, then mark out and drill all the holes in a stack of metal panels, five or ten or more at a time. If you make a mistake you've ruined the entire stack. Measure thrice, drill once!
@navtejsidhu8100 Жыл бұрын
Nic bro 👍
@MrPostFrame Жыл бұрын
Thanks!
@michaeljustiniano2958 Жыл бұрын
I’m confused as to why you don’t put that j channel on top of window prior to putting up the sheet metal?
@MrPostFrame Жыл бұрын
It's very difficult to get that metal in there if J-channel is already in place. There is a FJ trim at the top and to get a nice fit that piece of metal needs to be put in prior. Also, helps with getting that J-channel set properly at the top for water proofing purposes.
@t1reed110 ай бұрын
How do you trim out the j channel at the top of a window if the rib is close to the side?
@mkzenthusiasts Жыл бұрын
You do have a sheet metal sheers to snip that annoying beeper
@MrPostFrame Жыл бұрын
Ha...true!
@Geesum446 ай бұрын
I was not clear on those bottom tabs that were bent outward when you go to fit the the side piece to the bottom piece . Does the tab stick on top of the bottom piece between the window and the channel or does it slide inside the track of the bottom piece ?
@paulmaxwell88513 ай бұрын
Install the side j-trim, then bend that tab toward the center of the window, onto the bottom j-trim. NOT between the bottom j-trim and the window.
@jgronewold56 ай бұрын
Great video! Is it alright to use a stapler instead of a nailer to install the j trim? Or did you find that a nailer works better? When doing tin on a shouse have you ever ran the side pieces of J two inches longer than the window so it sticks past both ends 1" and then did the same diagonal cut 1/8" for a more finished look?
@paulmaxwell88513 ай бұрын
Personally, I don't trust staples to hold in the long run. I like screws. I did once try your idea, to get a mitered look. It was a real pain to make it look just right, and I'll never do it that way again. Just my two cents worth!
@jgronewold52 ай бұрын
@@paulmaxwell8851 Thanks for the advice! Appreciate your response.
@JamesS-vi5pv Жыл бұрын
How did you set the windows to have that over hang before the j trim. Was it a box frame ? Did you have all the nail flanges on the windows too. Thanks
@MrPostFrame Жыл бұрын
We have multiple videos on how we install our windows. The windows do have nail flanges. kzfaq.info/get/bejne/qdRmn6id2sqneps.html Window Playlist - kzfaq.info/sun/PL3QM32YjSVn3clsLAcMvCjaGfawG15Uns
@joha7484 Жыл бұрын
❤❤❤
@MrPostFrame Жыл бұрын
Thanks!
@milesboyer4657 Жыл бұрын
my windows do not have the j-trim filled in like the windows in the video, do i need to buy something to fill that void before installing the trim?
@MrPostFrame Жыл бұрын
No you can put your jtrim right up against the window and it will be just fine.
@briansdumbchannelderpy6986 Жыл бұрын
Like the Windsor windows?
@MrPostFrame Жыл бұрын
So far yes and they’re a good price point
@howlereves3281 Жыл бұрын
Always a video of wet-stabbing concrete, not an ideal practice 😼